欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    NAVISTAR MPAPS L-6606-2016 TITLE Insulation Floor Mat Dash & Carpet (E-5 Type).pdf

    • 资源ID:963063       资源大小:130KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    NAVISTAR MPAPS L-6606-2016 TITLE Insulation Floor Mat Dash & Carpet (E-5 Type).pdf

    1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. OCTOBER 2016 Page 1 of 5 NAVISTAR, INC. Material, Parts, and Process Specification

    2、s (MPAPS) NUMBER: MPAPS L-6606 Former Designation: TMS-6606 TITLE: Insulation, Floor Mat, Dash AMD: 35 kPa (5 psi) minimum. 4.3.2.2 Type IB 4.3.2.2.1 METHOD: ASTM D412 4.3.2.2.2 REQUIRED: 40 psi minimum 4.3.3 Splitting Resistance (Types IA and II only) 4.3.3.1 METHOD: ASTM D 461, Sample 5 x 15 cm (2

    3、 x 6 in). 4.3.3.2 REQUIRED: 4.45 N (1.0 lbf) minimum average, Peak of four samples, in both directions (AMD and WMD). 4.3.4 Air Flow Resistance (Types IA and II only) 4.3.4.1 METHOD: Using a 30 x 30 cm (12 x 12 in) sample, direct a stream of air towards the center portion at an angle of 45, using 62

    4、0-690 kPa (90-100 psi) air. The air nozzle shall have an opening of 2.16-2.41 mm (.085-.090 in) and shall be held 10 cm (4 in) above the surface for a min of 20 seconds. 4.3.4.2 REQUIRED: No visible delamination or separation when tested in two directions 180 apart. NUMBER: MPAPS L-6606 TITLE: Insul

    5、ation, Floor Mat, Dash Recovery: 70% minimum 4.3.5.2 Type IB 4.3.5.2.1 METHOD: ASTM D1056 4.3.5.2.2 REQUIRED: Compression: 50% maximum; Recovery 25% maximum 4.3.6 Mildew Resistance (Types IA and II only) 4.3.6.1 METHOD: AATCC-30, Section II. 4.3.6.2 REQUIRED: No objectionable odor immediately after

    6、test. 4.3.7 Flammability Requirement Material and parts supplied to this specification shall conform to and be certified by the supplier to meet the requirements of (CFR 49, Part 571.302) Federal Motor Vehicle Safety Standard #302 - Flammability of Interior Materials, and the requirements of MPAPS P

    7、-9544. 4.3.8 Sound Absorption Properties 4.3.8.1 METHOD: Test in accordance with ASTM C 384 (ASTM E 1050 is considered equivalent). 4.3.8.2 REQUIRED: Shall meet the indicated minimum requirements for absorption coefficients for each type as indicated below. 4.3.8.2.1 Type IA and IB: No specific acou

    8、stic absorption requirements 4.3.8.2.2 Type II: Normal-incidence absorption shall be measured at: 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, and 4000 Hz. The normal-incidence absorption coefficient at any one frequency shall not be less than 0.20 and the average of the normal incidence absor

    9、ption coefficients shall not be less than 0.70. 5.0 QUALITY This material shall have necessary flexibility to meet contour requirements without separation, and be free from residual asphalt and other contaminants which may cause the padding to stain trim cover materials. 6.0 QUALIFICATION Engineerin

    10、g qualification of sources is required in advance of production shipments. Samples shall be accompanied by test data certifying that all requirements of the specification have been met. Suppliers shall submit samples for approval of finish, luster, color and appearance to the Navistar Industrial Des

    11、ign Group. Upon approval, styling master samples denoting the minimum level of acceptable appearance quality shall be developed and retained by the supplier and the quality department of each using NAVISTAR facility. NUMBER: MPAPS L-6606 TITLE: Insulation, Floor Mat, Dash thickness 25mm NOTE: Existi

    12、ng drawings without any specific Type designation shall meet Type IA requirements. Type IA was previously noted as Type I. 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specificatio

    13、n by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ A.0 GENERAL INFORMATION APPROVED SOURCES Burkart Henderson, North Carolina Product: E-5 Janesville Products Norwalk, Ohio Product: Maratex Blachford Incorporated West Chicago, IL Product: Conasorb VSC3 REVISION HISTORY Revision Level Change Approved by Date Approved 1610 Converted to MPAPS R. Goluch 10/6/2016


    注意事项

    本文(NAVISTAR MPAPS L-6606-2016 TITLE Insulation Floor Mat Dash & Carpet (E-5 Type).pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开