1、 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 Navistar Inc. DECEMBER 2016 Page 1 of 5 NAVISTAR, INC. Material, Parts, and Process Specifications (
2、MPAPS) NUMBER: MPAPS F-7099 Former Designation: TMS-7099 TITLE: Fastener Tape Systems CURRENT REV No.: 1612 DATE: Dec. 2016 WRITTEN/EDITED BY: A. Hasan APPROVED BY: R. Goluch SUPERSEDES: Rev. 0912 Dec. 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may
3、involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. 1.
4、0 APPLICATION This specification covers synthetic fastener tapes or pads used for truck cab interiors. Various styles of fastener systems are available and attachment may be achieved by sewing, mechanically, or by adhesive coatings. 2.0 SCOPE This specification covers the general requirements for co
5、lor, roll length where applicable, adhesive backing if required, and colorfastness. Also included are the individual characteristics for one style (I) of tape. Other styles may be added to this specification if required. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product suppl
6、ied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in thi
7、s specification. Quality System Standard ISO 9001 or TS-16949 AATCC TM 8 CFR Title 29, Section 1910 ASTM D 1682 NAVISTAR Supplier Packing and Shipping Std. D-13 NAVISTAR Eng. Design Std. A-16 NAVISTAR MPAPS B-50 NAVISTAR MPAPS P-9543 4.0 GENERAL REQUIREMENTS The following general requirements apply
8、to all styles of tape supplied to this specification. 4.1 Individual Characteristics 4.1.1 Style I Woven hook and pile fastener tapes (Formerly TMS-7099 Grade A or B Style 1) NUMBER: MPAPS F-7099 TITLE: Fastener Tape Systems REVISION: 1612 This document is restricted and may not be sent outside Navi
9、star Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 Navistar Inc. DECEMBER 2016 Page 2 of 5 4.2 Construction Consists of a nylon hook tape and a nylon pile tape, each with a nylon ground. Two hook tapes are availa
10、ble (Grade A and B) with varying hook size and number of hooks per unit of area. GRADE A GRADE B Monofilament size (hook) 6.5 mil 8.0 mil Hooks per cm (in), min 55 (350) 27 (175) 4.3 Description Color, texture and finish of production material supplied must match master samples of the pre-production
11、 material originally approved and on file in the Master Fabric Book in the Navistar Industrial Design Department. 4.4 Roll Length (where applicable) Materials shall be supplied in 22, 45, or 90 m (25, 50, or 100 yd) rolls unless otherwise agreed upon by the supplier and using Navistar facility. 4.5
12、Adhesive Backing Adhesive backing, if required, shall be suitable for the intended application, providing adhesion to the substrate which exceeds the disengagement force of the fastener system. 4.6 Colorfastness: AATCC Test Method 8 Crocking test, performed both wet and dry, shall show no applicable
13、 staining of the contact fabric and have a minimum AATCC rating of four (4) when compared with the AATCC Color Transference Evaluation Chart. 4.7 Property And Performance Requirements 4.7.1 Tensile (Breaking) Strength: ASTM D 1682 The tensile strength of the individual tapes shall be as indicated in
14、 Table I below: TENSILE STRENGTH, kNlbf( )MINIMUM WIDTH, mm (in) 50(2) 38 (1-1/2) 25(1) 18(3/4) 16(5/8) Grade A Hook Tape 096215.( )064145.( )051115.( )03885.( )03680.( )Grade B Hook Tape 096215.( )170(76.0056125.( )044100.( )03680.( )Pile Tape 096215.( )067150.( )044100.( )02965.( )02760.( )4.7.2 T
15、he following tests shall be performed on tape assemblies using the standard pile tape in combination with the two grades of hook tape. NUMBER: MPAPS F-7099 TITLE: Fastener Tape Systems REVISION: 1612 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permissi
16、on from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 Navistar Inc. DECEMBER 2016 Page 3 of 5 4.7.2.1 Shear Strength (Lap Shear) Using an overlap of 76 mm (3 in), the shear strength shall be as follows: 4.7.2.1.1 Grade A Hook - 35 kPa (5 lbf/in) minimum 4
17、.7.2.1.2 Grade B Hook - 41 kPa (6 lbf/in) minimum 4.7.2.1.3 Rate of loading shall be 30 cm (12 in) per minute. 4.7.2.2 Lengthwise Peel Strength 4.7.2.2.1 Grade A Hook - 13 N/100 mm (0.75 lbf/in) width, minimum 4.7.2.2.2 Grade B Hook - 7 N/100 mm (0.40 lbf/in) width, minimum 4.7.2.2.3 Rate of loading
18、 shall be 30 cm (12 in) per minute. 4.7.3.3 Latching Strength Samples of the hook and pile tapes shall be affixed by adhesive to metal plates to form a sandwich consisting of the two plates with the tapes in contact with each other. The latching strength (force per unit area of tape contact) shall b
19、e determined by pulling in a direction perpendicular to the metal plates. 4.7.3.3.1 Grade A Hook - 35 kPa (5 psi) minimum 4.7.3.3.2 Grade B Hook - 28 kPa (4 psi) minimum 5.0 QUALIFICATION Material and processes submitted for approval to this specification shall include the following: 5.1 A detailed,
20、 signed test report documenting testing to this specification per MPAPS P-9543. 5.2 Test coupons or photographs showing failure modes for each test. 5.3 The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test specimens. 5.4 Qu
21、estions regarding qualification requirements, reports and test materials may be directed to: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN 6.0 QUALITY All product supplied shall be clean and free from dirt, oils, sharp edges, or
22、 defects harmful to product performance. 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIA
23、G PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. NUMBER: MPAPS F-7099 TITLE: Fastener Tape S
24、ystems REVISION: 1612 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 Navistar Inc. DECEMBER 2016 Page 4 of 5 7.2 Approval Parts supplied against con
25、tracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, co
26、nstruction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center, and Navistar Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification
27、, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall either perform and/or report results of tests on specific lots of parts produced using
28、 ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using Navistar p
29、lant may determine testing and reporting requirements on specific products. 8.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall be in accordance with NAVISTAR Supplier Packing and Shipping Standard D-13. 9.0 DESIGNATION ON DRAWINGS Shall include the color, width, styl
30、e and grade (where applicable), and the adhesive coating system (where required). Examples: 1) Style I, Grade A, per MPAPS F-7099 Color Width 2) Style I, Grade B, per MPAPS F-7099 with pressure sensitive adhesive backing Color Width NOTE: 1. All drawings referencing TMS-7099A are equivalent to Style
31、 I (Grade A or B as indicated). 2. The adhesive backing system shall be selected to meet the requirements of the intended application. NUMBER: MPAPS F-7099 TITLE: Fastener Tape Systems REVISION: 1612 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permissi
32、on from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 Navistar Inc. DECEMBER 2016 Page 5 of 5 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of t
33、his specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 11.0 APPROVED SOURCES (
34、Style I) (Formerly TMS-7099A) Grade A Hook Tape Loop Tape 3M Company SJ-3400 SJ-3401 Velcro USA, Inc. #65 #1000 Grade B Hook Tape Loop Tape 3M Company SJ-3402 SJ-3401 Velcro USA, Inc. #80 #1000 A.0 GENERAL INFORMATION (Not a Requirement of the Specification) As indicated in the Application section,
35、many styles of fastening systems are available, including variations in the attachment and/or the material (yarn). A.1 The methods of attachment of these fasteners are numerous, including sewing, use of pressure sensitive adhesives, solvent activated adhesives, heat activated adhesives, or by mechan
36、ical means. Selection of the particular attachment system is dependent upon the design or application, the substrate, and the intended means of application of the parts being attached. A.2 Since the adhesive systems vary considerably in their applicability to varying situations, it is extremely impo
37、rtant that they be selected with care, and the use of parts already in the system in other applications be done only after careful consideration of the adhesive package. Definition of the particular adhesive system shall be included with the drawing covering each individual application. REVISION HISTORY Revision Level Change Approved by Date Approved 1612 Converted to MPAPS R. Goluch 12/6/2016
