欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    NAVISTAR MPAPS DT-4-2016 Impact Test For Plastics.pdf

    • 资源ID:962926       资源大小:104.25KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    NAVISTAR MPAPS DT-4-2016 Impact Test For Plastics.pdf

    1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 1 of 2 NAVISTAR, INC. Material, Parts, and Process Specifications

    2、(MPAPS) NUMBER: MPAPS DT-4 Former Designation: CEMS DT-4 (example) TITLE: Impact Test For Plastics CURRENT REV No.: 1606 DATE: June 2016 WRITTEN/EDITED BY: W. Cook APPROVED BY: R. Goluch SUPERSEDES: April 2010 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification m

    3、ay involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use.

    4、 1.0 SCOPE This is a method to determine the 50% failure level (FL50), in the impact test, for thermoplastic test panels or production parts. 2.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following specifications and standards are re

    5、ferenced in this specification: ASTM D 5420 3.0 APPARATUS 3.1 Impact tester per ASTM D 5420 except male punch (indenter) will be 0.625 inch (15.88 min) diameter and the female die (support ring) will be 2.0 inch (50 mm) OD and 1.250 inch (31.75 mm) ID. 3.2 Micrometer, 0 to 1 inch (0 to 25 mm). 3.3 I

    6、mpact weights: 0.5, 1.0, 2.0, 4.0 and 6.0 lb (0.23, 0.45, 0.91, 1.81 and 2.72 kg). 4.0 TEST SPECIMENS Test specimens will be at least 2.0 inches (50 millimeters) square. On larger specimens, impact sites to be at least 2.0 inches between centers. 5.0 PROCEDURE 5.1 Visually inspect test specimens. Di

    7、scard any that exhibit cracks, crazes, etc., which may affect strength. 5.2 Locate and mark the impact sites on the test specimens. Measure the thickness at each site and record to the nearest 0.001 inch (0.025 mm). Specimen thickness at each site must agree within 2% for valid comparison of impact

    8、data. 5.3 Maintain apparatus and specimens at test temperature for no less than 16 hours prior to testing. 5.4 Install the 0.5 lb. (0.23 kg) impact weight and impact foot slightly and place a test specimen on the tester anvil, with the steel ring removed. Lower the foot to impact site and make certa

    9、in that the specimen rests flat on the anvil. 5.5 Lift the weight the full 40 inches (1.02 meters) and release. 5.6 Inspect the specimen for failure. 5.7 Failure is defined as cracks, splits or breaks which appear as a result of the impact on the surface of the test specimen. Usually, cracking occur

    10、s on the surface opposite the impact surface. NUMBER: MPAPS DT-4 TITLE: Impact Test for Plastics CURRENT ISSUE DATE: JUNE 2016 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume

    11、all patent liability. 2016 by Navistar, Inc. JUNE 2016 Page 2 of 2 5.8 If no failure is noted, repeat Steps 4 and 5 using a new specimen each time with successively larger weights until a failure is noted. 5.9 If a failure is noted, proceed to 5.10; however, if no failure is noted at 40 inches with

    12、the 6.0-lb. weight, then test nine additional specimens at this level and report the percent that pass. 5.10 When a failure is noted at a 40-inch level, using the same weight, reduce the height by 50% and test another specimen. Continue retesting, halving the height each time, until a pass is noted.

    13、 5.11 When a pass is noted, impact each successive specimen from a height midway between the last fail and last pass levels until these points are about 6 inches (152 mm) apart. 5.12 Starting at a point midway between the last two levels (5.9) continue testing, raising the impact height 1 inch (25 m

    14、m) each time a specimen passes and lowering it 1 inch each time a specimen fails. Use a minimum of 15 test specimens. 6.0 CALCULATIONS Calculate the FL50 using the following equation: FL50=SNW N = the number of specimens that failed or passed in 5.12 (whichever is smaller). S = the sum of the impact

    15、 heights for the specimens that comprise “N”. W = the impact weight used in Step 12. 7.0 REPORT 7.1 The final impact weight used 7.2 The thickness of the specimens tested 7.3 The FL50 or the % pass from 5.7. REVISION HISTORY Revision Level Change Approved by Date Approved 1606 Converted to MPAPS R. Goluch 5/24/2016


    注意事项

    本文(NAVISTAR MPAPS DT-4-2016 Impact Test For Plastics.pdf)为本站会员(twoload295)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开