1、*USACE / NAVFAC / AFCESA / NASA UFGS-12 34 00 (May 2010)-Preparing Activity: NASA SupersedingUFGS-12 34 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2010*SECTION TABLE OF CONTENTSDIVISION 12 - FURNISHINGSSECTION 12 34 00MANUFACTURED PLASTIC CA
2、SEWORK05/10PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 DESIGN1.4 QUALITY ASSURANCE1.5 DELIVERY, STORAGE, AND HANDLINGPART 2 PRODUCTS2.1 SYSTEM DESCRIPTION2.2 MATERIALS2.3 MISCELLANEOUS CABINETS2.3.1 Combination Sink-and-Base Cabinet2.3.2 Special Purpose Cabinets2.4 ACCESSORIES AND HARDWARE2.5 CABI
3、NETS2.6 FINISH2.6.1 Cabinet Finish2.6.2 Backer Sheets2.7 COLOR, TEXTURE, AND PATTERNPART 3 EXECUTION3.1 INSTALLATION3.2 CLEANING3.3 INSPECTION- End of Section Table of Contents -SECTION 12 34 00 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*
4、USACE / NAVFAC / AFCESA / NASA UFGS-12 34 00 (May 2010)-Preparing Activity: NASA SupersedingUFGS-12 34 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2010*SECTION 12 34 00MANUFACTURED PLASTIC CASEWORK05/10*NOTE: This guide specification covers t
5、he requirements for manufactured plastic casework.Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective pr
6、oject, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Rec
7、ommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in thi
8、s paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the
9、 issue dates.SECTION 12 34 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish pr
10、int process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.ASME INTERNATIONAL (ASME)ASME B18.6.1 (1981; R 2008) Wood Screws (Inch Series)ASTM INTERNATIONAL (ASTM)ASTM A 167 (199
11、9; R 2009) Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripASTM A 325 (2009) Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthASTM A 325M (2009a) Standard Specification for Structural Bolts, Ste
12、el, Heat Treated, 830 MPa Minimum Tensile Strength (Metric)ASTM C 1036 (2006) Standard Specification for Flat GlassASTM D 4000 (2009b) Standard Classification System for Specifying Plastic MaterialsASTM D 4689 (1999; R 2005) Standard Specification for Adhesive, Casein-TypeASTM D 4690 (1999; R 2005)
13、Standard Specification for Urea Formaldehyde Resin AdhesivesASTM F 594 (2008) Standard Specification for Stainless Steel NutsASTM F 836M (2002) Standard Specification for Style 1 Stainless Steel Metric NutsBUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)ANSI/BHMA A156.9 (2003) Cabinet HardwareKITC
14、HEN CABINET MANUFACTURERS ASSOCIATION (KCMA)KCMA A161.1 (2000) Performance Nail, Expansion; and Nail, Drive Screw (Devices, Anchoring, Masonry)FS TT-C-490 (1990; Am 2) Cleaning Methods for Ferrous Surfaces and Pretreatments for Organic CoatingsFS TT-C-520 (Rev B; Am 1) Coating Compound, Bituminous,
15、Solvent Type, Underbody (for Motor Vehicles)FS TT-E-491 (Rev C) Enamel; Gloss, Synthetic (for Metal and Wood Furniture)FS TT-F-336 (Rev E) Filler, Wood, PasteFS WW-P-541 (1990e; Am 1) Plumbing Fixtures1.2 SUBMITTALS*NOTE: Review Submittal Description (SD) definitions in Section 01 33 00 SUBMITTAL PR
16、OCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked
17、with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army project
18、s, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for SECTION 12 34 00 Page 4Provided by IHSNot for ResaleNo reproduction or network
19、ing permitted without license from IHS-,-,-Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force
20、, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval
21、.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsFabrication Drawings; G; G, _Installation Drawings;
22、G; G, _SD-03 Product DataCatalog Data; G; G, _SD-04 SamplesCasework Samples; G; G, _Accessories and Hardware; G; G, _Manufacturers Standard Color Charts; G; G, _SD-07 CertificatesCertificates of Conformance; G; G, _SD-08 Manufacturers InstructionsManufacturers Instructions; G; G, _1.3 DESIGNFurnish
23、plastic laminate cabinets, factory-fabricated and finished in the manufacturers standard sizes and finishes of the type, design, and configuration indicated. Construct cabinets as specified and meet the requirements of KCMA A161.1. Submit fabrication drawings for review and approval prior to commenc
24、ement of fabrication. Provide wall and base cabinet assemblies consisting of individual units joined into continuous sections. Accomplish fastenings to permit removal and replacement of individual units without affecting the remainder of the installation. Provide counters with watertight sink rim wh
25、en indicated. Provide removable drawers equipped with position stops to avoid accidental complete withdrawals. Fix or adjust shelves as indicated.SECTION 12 34 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1.4 QUALITY ASSURANCESubmit certi
26、ficates of conformance for the following items showing conformance with the referenced standards contained in this section:a. Corrosion-resistant steelb. Glassc. Adhesivesd. Filler materiale. Fastenersf. Service fixturesg. Accessories and hardware1.5 DELIVERY, STORAGE, AND HANDLINGDeliver, handle, a
27、nd store cabinets in a manner that will prevent damage or deformity. Provide temporary skids under units weighing more than _ kilogram pounds.PART 2 PRODUCTS2.1 SYSTEM DESCRIPTIONSubmit manufacturers catalog data for the following items:a. Cabinetsb. Glassc. Adhesivesd. Filler materiale. Fastenersf.
28、 Service fixturesg. Accessories and hardwareh. Plastic laminatei. Steel sinksj. CountertopsSubmit manufacturers standard color charts for plastic cabinets showing the manufacturers recommended color and finish selections.Submit casework samples in accordance with ASTM D 4000, and include accessories
29、 and hardware, one each. Submit manufacturers instructions for plastic cabinet systems including special provisions required to install equipment components and system SECTION 12 34 00 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-packages, a
30、nd any special notices detailing impedances, hazards and safety precautions. Provide the manufacturers cabinets with the standard sizes, type, and design indicated. Both wall and base cabinet assemblies will consist of individual units joined into continuous sections as indicated. Accomplish fasteni
31、ngs to permit removal and replacement of individual units without affecting the remainder of the installation.2.2 MATERIALS*NOTE: Delete any of the following materials that are not applicable.* Provide Corrosion-Resistant steel conforming to ASTM A 167, Type 302 304 316 Finish 4.Provide glass confor
32、ming to ASTM C 1036, Type I, Class 1, Quality q3, 6 millimeter 1/4 inch thick, for unframed sliding glass doors; and other glass conforming to ASTM C 1036, Type II, Class 1, Quality q8, 5 millimeter7/32 inch thick.Provide thermosetting urea-resin Type II adhesives for application of plastic laminate
33、 conforming to ASTM D 4690 as recommended by the manufacturer of the laminate. Provide adhesive for wood members conforming to ASTM D 4689.Provide filler material conforming to FS TT-F-336.*NOTE: Review NEMA LD 3 and insert style, type, grade, class, and finish as required.*Provide plastic laminate
34、that conforms to NEMA LD 3, Style _, Type _, Grade _, Class _, Finish _.Provide accessories and hardware conforming to the following requirements, as applicable:Extension drawer slides: ANSI/BHMA A156.9, Type B85071Semiconcealed hinges: ANSI/BHMA A156.9, Type B81201, 40 millimeter 1-1/2 inchesFull s
35、urface hinges: ANSI/BHMA A156.9, Type B81131, 40 millimeter 1-1/2 inchesKnob pulls: ANSI/BHMA A156.9, Type B12132 25 millimeter 1-inch diameterBar type pulls: ANSI/BHMA A156.9, Type B12012 100 millimeter 4-inch overall lengthLocks, keying, and keys: As directedCatches: Magnetic, 22 newton 5-pound pu
36、llSECTION 12 34 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Sliding door set:Nylon glides_Provide fasteners conforming to the following:Screws: ASME B18.6.1, Group, Type and Class as applicableAnchoring Devices: FS FF-S-325, Group, Type,
37、 and Class as applicableToggle bolts: FS FF-B-588, Type I, Class A, Style 2Nuts: ASTM F 836M ASTM F 594, corrosion-resistant steelBolts: ASTM A 325M ASTM A 325, heavy, hexagon head bolts corrosion-resistant steel*NOTE: Sink for inset-type installation is as specified in Section 22 00 00 PLUMBING, GE
38、NERAL PURPOSE.* Integral Corrosion-resistant steel sinks: 1.3 millimeter 18-gage corrosion-resistant steel, integral with corrosion-resistant steel countertop 1.3 millimeter 18-gage corrosion-resistant steel, nonintegral, self-rimming Drain holes in center of bowlUnderside coated with 3 millimeter 1
39、/8-inch thick sound deadenerDie-form, seamless, raised edges at front and endsCove corners to 13 millimeter 1/2-inch radiusEquip with strainers and tail piecesProvide Sound deadening conforming to FS TT-C-520.Provide service fixtures conforming to the following requirements:Provide fixtures in accor
40、dance with the water conservation policy as stated in the Standard Plumbing Codes, Appendix J.Faucets: Splashback mounted, cast brass, chrome plated, FS WW-P-541Faucets: Deck mounted, cast brass, chrome plated, FS WW-P-541Gas, air, and vacuum, distilled water, steam, and de-ionized water cocks: Cast
41、 brass, chrome plated, ground key typeDrains, strainers, and taps: Brass, chrome plated, FS WW-P-541SECTION 12 34 00 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Index buttons: Plastic, color codes in accordance with SEFA 7Special items: Nip
42、ples and locknuts with each fixture will be as directed.*NOTE: Delete any of the following types that are not applicable.Type I, zinc phosphateType II, iron phosphateType III, organic-paint, varnish, lacquer* Metal pretreatment coatings: FS TT-C-490, Type I Metal pretreatment coatings: FS TT-C-490,
43、Type II Metal pretreatment coatings: FS TT-C-490, Type III Enamel: FS TT-E-491, Class 22.3 MISCELLANEOUS CABINETS*NOTE: Delete inapplicable paragraphs, or state appropriate options.*2.3.1 Combination Sink-and-Base CabinetProvide sink with matching drainboards, made of corrosion-resistant steel porcelain-enamel steelplastic laminatesolid surfacefiberglass composites; equipped with a chromium-plated swinging-spout faucet, chromi
