1、STDSITU-T RECMN T-433 AMD 1-ENGL 1995 48b2591 Ob3b754 O32 = INTERNATIONAL TELECOMMUNICATION UNION ITU=T TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU Amendment 1 T.433 (08/95) TERMINALS FOR TELEMATIC SERVICES DOCUMENT TRANSFER, ACCESS AND MANIPULATION (DTAM) - SERVICES AND PROTOCOLS - PROTOCOL SPE
2、CIFICATION AMENDMENT I: REVISIONS OF T.433 TO SUPPORT G4 COLOUR AND FILE TRANSFER Amendment I to IT U -T Recommend at ion T .43 3 (Previously “CCITT Recommendation“) Recommendation T.433 / Amd.1 (08/95) I STD-ITU-T RECMN T.433 AMD 1-ENGL 1995 48b259L Ob3b755 T79 FOREWORD The ITU-T (Telecommunication
3、 Standardization Sector) is a permanent organ of the International Telecommunication Union (ITU). The ITU-T is responsible for studying technical, operating and tariff questions and issuing Recommendations on them with a view to standardizing telecommunications on a worldwide basis. The World Teleco
4、mmunication Standardization Conference (WTSC), which meets every four years, establishes the topics for study by the ITU-T Study Groups which, in their turn, produce Recommendations on these topics. The approval of Recommendations by the Members of the ITU-T is covered by the procedure laid down in
5、WTSC Resolution No. 1 (Helsinki, March 1-12, 1993). Amendment 1 to ITU-T Recommendation T.433, was prepared by ITU-T Study Group 8 (1993-1996) and was approved under the WTSC Resolution No. 1 procedure on the 1 lth of August 1995. NOTE In this Recommendation, the expression “Administration” is used
6、for conciseness to indicate both a telecommunication administration and a recognized operating agency. O ITU 1995 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permis
7、sion in writing from the ITU. II Recommendation T.433 / Amd.1 (08/95) CONTENTS 1 Introduction . 2 Modification of Recommendation T.433 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.1 1 2.12 8.2 The second paragraph of 5.3.2 in Recommendation T.433 should be replaced by the following new paragraph . The
8、 following new subclause should be added after 6.2.4.3.1.5 in Recommendation T.433 . The following new subclause should replace 6.2.4.3.2 in Recommendation T.433 . The following new subclause should be added after 6.5.4.1 . 1 . 5 in Recommendation T.433 . The following new subclauses should replace
9、6.5.4.1.2 in Recommendation T.433 The following new paragraph should be inserted after the title 6.6.3.2 in Recommendation T.433 . Figure 3 should be replaced with following new figure . Inseri new subclause 6.2.4.3.3 Subclause 7.3.5.2 in Recommendation T.433 should be replaced by the following new
10、subclause . Modules to be imported in DTAM APDU defined in 8.1 should be replaced by the following new modules . Abstract syntax definition of Applicationlapabilities used in DTAM normal mode should be replaced by the following new definition Subclause 8.2 should be replaced by the following new sub
11、clause Abstract syntax definition of APDUs for use of the session service in Transparent Mode . Page 1 1 1 1 2 2 2 2 2 3 3 4 4 4 4 Recommendation T.433 / Amd.1 (08195) iii STD-ITU-T RECMN T.Li33 AMD 1-ENGL 1495 D 48b2591 Ub3b757 841 9 SUMMARY Recommendation T.433 currently defines the document bulk
12、transfer of Group 4 Telefax documents as the DTAM transparent mode and of arbitrary documents and binary files in the DTAM normal mode. Amendment 1 provides for the transfer of binary files (based upon Recommendation T.434), and other formats, such as DTM, JPEG, EDIFACT and also Colour facsimile doc
13、uments in the DTAM transparent mode. This amendment mainly concentrates on the amendments for the association establishment, where the relevant formats need to be recognized, and on the transfer phase, where segmenting must be extended to information that is not structured page by page. iv Recommend
14、ation T.433 / Amd.1 (08/95) STD-ITU-T RECMN T-433 AMD 1-ENGL 1975 D 48b2591 Ob3h758 788 Amendment 1 to Recommendation T.433 REVISIONS OF T.433 TO SUPPORT G4 COLOUR AND FILE TRANSFER (Geneva, 1995) 1 Introduction This contribution contains the revision of existing Recommendations T.433 in order to su
15、pport colour and file transfer extension for G4 facsimile application. 2 Modification of Recommendation T.433 2.1 The second paragraph of 5.3.2 in Recommendation T.433 should be replaced by the following new paragraph 5.3.2 Functions of DTAM service-provider 2) DTAM capability The DTAM capability is
16、 defined by sets of parameters in order to specify the communication features: ODA application capabilities a) document application profile; b) operational application profile; c) non-basic document characteristics; d) non-basic structural characteristics; and e) additional document characteristics,
17、 etc. File transfer capabilities a) BFT capabilities; b) Transparent Data Capabilities; c) DTM capabilities; d) EDIFACT capabilities. Private capabilities 2.2 6.2.4.3.1.6 Additional document characteristics The value of this parameter is any combination of additional document Characteristics defined
18、 in Recommendation T.414. The following new subclause should be added after 6.2.4.3.1.5 in Recommendation T.433 Recommendation T.433 / Amd.1 (08/95) 1 STD-ITU-T RECMN T.433 AID 1-ENGL 1775 D 48b2571 Ob3b757 bL4 a 2.3 The following new subclause should replace 6.2.4.3.2 in Recommendation T.433 6.2.4.
19、3.2 File transfer capabilities This parameter specifies file transfer capabilities which are available to the sender of this parameter as receiving capabilities. The parameter is present in both, the Transparent Mode and Normal Mode. - BFT (Binary File Transfer) capabilities This value indicates the
20、 capability to receive files encoded to the specification of Recommendation T.434. - Transparent data capabilities This value indicates that the sender is ready to accept (when acting as a receiver) data that are transferred completely transparently. DTM (Document Transfer Mode) capabilities This va
21、lue indicates the capability to receive BFT files (defined in Recommendation T.434) encoded to the DTM encoding rules defined in Recommendation T.563. EDIFACT (electronic data exchange) capabilities This value indicates the capability to receive files encoded to the EDIFACT formats defined in ISOIIE
22、C 9735. - - 2.4 Insert new subclause 6.2.4.3.3 6.2.4.3.3 Private capabilities This parameter indicates capabilities for private values. DTAM-PM does not care the contents of this parameter. This parameter is only present in the Transparent Mode. 2.5 6.5.4.1.1.6 Additional document characteristics Th
23、e value of this parameter is any combination of additional document characteristics defined in Recommendation T.414. The following new subclause should be added after 6.5.4.1.1.5 in Recommendation T.433 2.6 The following new subclauses should replace 6.5.4.1.2 in Recommendation T.433 6.5.4.1.2 File
24、transfer capabilities This parameter specifies file transfer capabilities which are available to the sender of this parameter as receiving capabilities. The parameter may be present in the Transparent Mode and Normal Mode. 6.5.4.1.3 Private capabilities See 6.2.4.3.3. 2.7 The following procedure is
25、applied to the transfer of G4 facsimile documents (according to Recommendation T.503) and to the transfer of files. The interchange data elements are to be interpreted in relationship with the T.503 document structure. In the case of file transfer, segmenting of the file will be carried out accordin
26、g to the length of the segment and the transfer procedure has to be applied accordingly to the segments of files as specified below for the interchange data elements. The following new paragraph should be inserted after the title 6.6.3.2 in Recommendation T.433 2 Recommendation T.433 I Amd.1 (08/95)
27、 STD-ITU-T RECMN T-Li33 AND 1-ENGL 1995 LiBb2591 Ob3b7bO 33b a 2.8 Subclause 7.3.5.2 in Recommendation T.433 should be replaced by the following new subclause 7.3.5.2 Use of S-DATA request and indication primitive parameters The document information is divided into segments such that the segment bou
28、ndaries coincide with the minor synchronization points. Each segment consists of an integral number of interchange data elements, or in the case of file transfer, consists of the data which is subdivided into the segment of size indicated by the user. The interchange data elements of each segment ar
29、e encoded using the Basic Encoding Rules defined in Recommendation X.209. The encoded interchange data elements of each segment are concatenated, forming an encoded segment. 2.9 Figure 3 should be replaced with following new figure S-ACTIVITY-START-user-data := CHOICE ( 4 IMPLICT DocumentCharacteris
30、tics DocumentCharacteristics := SET documentAppiicationProfile := CHOICE O IMPLICIT OCTET STRING, - 01 H Non-DocumentApplicationProjle - 02 H DocumentApplicationProfile T. 503 - 03 H DocumentApplicationProjZe T.501 - Other values are assigned by Recommendation T 563 141 IMPLICIT SET OF OBJECT IDENTI
31、FIER ), 1 J IMPLICIT OCTET STRING OPTIONAL, - 00 H means FDA documentArchitectureClass nonBasicDocumentCharacteristics 121 IMPLICIT NonBasicDocumentCharacteristics nonBasicStructuralC haracteristics 131 IMPLICIT NonBasicStructuralCharacteristics fileTransferCapabiiities 101 IMPLICIT FileTransferCapa
32、bilities OPTIONAL, OPTIONAL, OPTIONAL ) NonBasicDocumentCharacteristics := SET commentsCharacterSets pageDimensions ZJ IMPLICIT SET OF Dimension-Pair OPTIONAL, ra-gr-coding-attributes OPTIONAL, 1 I IMPLICIT OCTET STRING OPTIONAL, - string of escape sequences 131 IMPLICIT SET OF Ra-Gr-Coding-Attribut
33、e - Ra-Gr-Coding-Atribute is defined in - Recommendation T.415 Ra-Gr-Presentation-Features OPTIONAL - Ra-Gr-Presentation-Features is de$ned in - Recommendation T.415 ra-gr-presentation-features 141 IMPLICIT SET OF NonBasicStructuralCharacteristics := SET numberOfObjectPerPage 101 IMPLICIT INTEGER OP
34、TIONAL FIGURE 3n.433 User data in S-ACTIVITY-START/RESUME Recommendation T.433 / Amd.1 (08/95) 3 STD-ITU-T RECMN T-433 AMD 1-ENGL 1995 Lib2571 Ub3b7bL 272 2.10 Modules to be imported in DTAM APDU defined in 8.1 should be replaced by the following new modules IMPORTS DocumentProfileDescriptor, Layout
35、ClassDescriptor, Textunit, LogicalClassDescriptor, LogicalObjectDescriptor, LayoutStyleDescriptor, DocumentApplicationProfile, NonBasicDocCharacteristics, NonBasicStrucCharacteristics, AdditionalDocCharacteristics - ODA - FROM Interchange-Data-Elements( joint-iso-ccitt 8 1 5 5 2.11 Abstract syntax d
36、efinition of ApplicationCapabilities used in DTAM normal mode should be replaced by the following new definition ApplicationCapa bilities := CHOICE oDAApplicationCapabilities O IMPLICIT SET oDADocumentApplicationProfile O IMPLICIT OBJECT IDENTIFIER, nonBasicODADocumentCharacteristics i NonBasicDocCh
37、aracteristics OPTIONAL, nonBasicODAStructuraICharacteristics 121 NonBasicStrucCharacteristics OPTIONAL, operationalApplicationProfile 131 IMPLICIT SET OF OBJECT IDENTIFIER OPTIONAL additionalDocCharacteristics 4 IMPLICIT AdditionalDocCharacteristics OPTIONAL, i IMPLICIT INTEGER ( I fileTransferCapa
38、bilities bftcapabilities (O), dtmcapabilities (2), edilapabilities (3) transparentDataCapabilities (i), 1 1 2.12 Subclause 8.2 should be replaced by the following new subclause 8.2 This abstract syntax is described by the notation of ASN.1 defined in the Recommendation X.208. Abstract syntax definit
39、ion of APDUs for use of the session service in Transparent Mode I D-INITIATE-REQ := CHOICE 141 IMPLICIT ApplicationCapabilitics ApplicationCapa bilities := SET documentApplicationProfileT73 O IMPLICIT OCTET STRING OPTIONAL, - 01 H Non-DocumentApplicationProfile - 02 H DocumentApplicationProjle T.503
40、 - 03H DocumentAppiicationProfile T.501 - Other values are assigned by Recommendation T.563 documentArchitectureClass i IMPLICIT OCTET STRING OPTIONAL ) - 00“ means FDA 121 D-INITIATE-RES := CIIOICE ( 41 IMPLICIT ApplicationCapabilitics 1 ApplicationCapabilities := SET documentApplicationProfileT73
41、O IMPLICIT OCTET STRING OPTIONAL, - O1 H Non-DocumentApplicationProfiie - 02 H DocumentAppiicationProfile T.503 - 03 H DocumentApplicationProfile T.501 - Other values are assigned by Recommendation T. 563 documentArchitectureClass il LMPLICIT OCTET STRING OPTIONAL - 00H means FDA 4 Recommendation T.
42、433 / Amd.1 (08/95) STD-ITU-T RECMN Te433 AND 1-ENGL 1975 = LIb257L Ob3b7b2 LO7 H (31 D-CAPABILITY-REQ := CHOICE ( (41 IMPLICIT ApplicationCapabilities ApplicationCapabilities := SET ( documentApplicationProfileT73 documentArchitectureClass nonBasicDocCharacteristics nonBasicStrucCharacteristics add
43、itionaIDocCharacteristics fileTransferCapabilities privateCapabilities O IMPLICIT OCTET STRING OPTIONAL, i IMPLICIT OCTET STRING OPTIONAL, (21 IMPLICIT NonBasicDocCharacteristics OPTIONAL, 3 IMPLICIT NonBasicStrucCharacteristics OPTIONAL, 9 IMPLICIT AdditionalDocCharacteristics OPTIONAL, lo IMPLICIT
44、 SET OF FileTransferCapabilities OPTIONAL, li IMPLICIT OCTET STRING OPTIONAL - “NonBasicDocCharacteristics “, “NonBasicStrucCharacteristics “ and - “AdditionalDocCharacteristics“ are imported from Recommendation T. 41 5 141 D-CAPABILITY-RES := CHOICE ( 141 IMPLICIT ApplicationCapabilities Applicatio
45、nCapabilities := SET ( documentApplicationProfileT73 documentArchitectureClass nonBasicDocC haracteristics nonBasicStrucCharacteristics additionalDocCharacteristics fileTransferCapa bilities privateCapabilities FileTransferCapabilities := INTEGER O IMPLICIT OCTET STRING OPTIONAL, i IMPLICIT OCTET ST
46、RING OPTIONAL, 121 IMPLICIT NonBasicDocCharacteristics OPTIONAL, (31 IMPLICIT NonBasicStrucCharacteristics OPTIONAL, 9 IMPLICIT AdditionalDocCharacteristics OPTIONAL, 101 IMPLICIT SET OF FileTransferCapabilities OPTIONAL, bftlapabilities (O), transparentDataCapability (119 dtmCapabilities (219 ediCapabilites (3) 1 1 i IMPLICIT OCTET STRING OPTIONAL Recommendation T.433 I Amd.1 (08/95) 5
