欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    INTERN TMS 6930-2009 Glass Assembly Adhesive《玻璃总成粘合剂》.pdf

    • 资源ID:786134       资源大小:171.14KB        全文页数:7页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    INTERN TMS 6930-2009 Glass Assembly Adhesive《玻璃总成粘合剂》.pdf

    1、This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 1 of 7 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS

    2、-6930 srr TITLE: Glass Assembly Adhesive CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE DATED: August 2002 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve haza

    3、rdous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice:

    4、 Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 30-1 Keywords: Glass Bonding, Adhesives, Adhesive systems 1.0 APPLICATION This specification covers glass assembly adhesive systems us

    5、ed primarily for bonding laminated or tempered glass to metal or plastic components in the construction of trucks and tractors. Components include such items as: studs, latches, hinges, and sashes, etc. 2.0 SCOPE This specification covers the material properties, performance requirements, production

    6、 quality and process control, suppliers responsibility, source approval and quality control, general information, and sources for approved adhesive systems. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with t

    7、he requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards applies. The following specifications, standards, and regulations are referenced herein. Quality System Standard ISO 9001 or TS-16949 NAVISTAR TMS-9522 CFR

    8、 Title 29, Section 1910 NAVISTAR TMS-9543 NAVISTAR Manufacturing Std. MS-D-13 SAE J243 NAVISTAR Eng. Design Std. A-16 SAE J1523 NAVISTAR CEMS B-50 ASTM D 1002 NAVISTAR CEMS C-10 ASTM D 3163 NAVISTAR CEMS G-5 ASTM B 117 NAVISTAR CEMS GT-7E 4.0 GENERAL REQUIREMENTS Adhesive materials supplied to this

    9、specification shall bond the intended substrates to produce a permanent and structural bond. The general properties of as-received materials in the uncured state are listed in Table 5. It is the responsibility of the adhesive supplier to insure compatibility of the new Copyright Navistar Internation

    10、al Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permiss

    11、ion from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 2 of 7 adhesive materials with the Assembly Plants product materials and processes and obtain approval from the Production Process Manager of the Assembly Plant for th

    12、e use of new adhesive materials. 4.1 General Properties All properties shall be reported on submitted test reports and specific material properties will be included in Table 4. Performance requirements are listed in Section 4.3. 4.1.1 Uncured Properties Requirements for specific uncured properties a

    13、re to be agreed upon between the material supplier, equipment supplier and the applicator. Uncured properties shown herein are provided for reference only. 4.2 Sample Preparation A minimum of five samples shall be prepared for each condition tested. Prepare samples per SAE J1523 except as indicated.

    14、 See Figure 1. The surface condition tested shall be representative of production conditions and fully described in the test report. The bond line shall be between .5 and 1 mm (.020 and .040 inches) with an overlap of 12.5 mm (.5 inch) unless otherwise directed. The cure conditions* shall be describ

    15、ed fully in the test report and should closely match the production cure conditions. These cure conditions will be listed on the attached tables and shall be reproducible for future testing. * Times and temperatures should represent actual bond line conditions. 4.3 Property And Performance Requireme

    16、nts 4.3.1 Lap Shear Strength 4.3.1.1 Method: Prepare samples as directed in 4.2 Sample Preparation. Test per ASTM D 3163 or ASTM D 1002, as appropriate. Tensile machine jaw separation rate shall be 13 mm (.5 in) per minute. Test overlap shear at the indicated specified temperatures (see Table 1) aft

    17、er holding at temperature for 30 minutes. Report the average failure loads of the five tests. 4.3.1.2 Required: See Table 1 for required values. TABLE 1: BOND STRENGTH (1) Lap Shear (1) Material: Glass to Metal Condition MPa psi minimum (1) 25 2C * 2.1 305 (2) -40 2C * 2.1 305 120 2C * 1.5 218 (2) H

    18、eat Age 2.1 305 Water Immersion 2.1 305 (2) 500 hr Humidity 2.1 305 1000 hr Humidity 2.1 305 Cyclic Aging 2.1 305 (2) *Test at these conditions. (1) Samples will be pulled at the rate as specified in 4.3.1 Lap Shear Strength until failure. Report the failure mode for each test. (2) Screening tests.

    19、Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc.

    20、 or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 3 of 7 4.3.1.3 Humidity 4.3.1.3.1 Method: Test per CEMS GT-7E on coupons prepared in 4.2 Sample Preparation for length of time (see Table

    21、 1) and then perform shear test upon removal from humidity. Shear strength test for 500 hours. 4.3.1.3.2 Required: See Table 1. 4.3.1.4 Water Immersion 4.3.1.4.1 Method: Prepare coupons per Section 4.2 Sample Preparation. Immerse coupons in distilled water at 25C 2C (77F 3.6F) for 500 hours. Perform

    22、 shear strength test as soon as samples are removed from immersion. 4.3.1.4.2 Required: See Table 1. OVERLAP SHEAR TEST SAMPLE 4.3.1.5 Heat Aging 4.3.1.5.1 Method: Prepare samples for lap shear as directed in 4.2 Sample Preparation. Heat age in a recirculating air oven for 500 hours at 90 2C (194 3.

    23、6F). Perform shear test, as indicated in Section 4.3.1.1, upon removal from heat aging. 4.3.1.5.2 Required: See Table 1. 4.3.1.6 Cyclic Aging 4.3.1.6.1 Method: Prepare samples for lap shear as directed in 4.2 Sample Preparation. Test overlap shear after the 6-week environmental conditioning period l

    24、isted below, allowing samples to return to ambient room temperature for 24 hours prior to testing. The 6-week cyclic aging shall be as follows: 4.3.1.6.1.1 16 hours humidity 4.3.1.6.1.2 2 hours -30 2C (-22 3.6F) 4.3.1.6.1.3 2 hours at ambient conditions 4.3.1.6.1.4 2 hours 70 2C (158 3.6F) 4.3.1.6.1

    25、.5 2 hours salt spray per ASTM B 117 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and

    26、may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 4 of 7 4.3.1.6.1.6 Repeat 24 hour cycle until 6-week period has elapsed - cycle may be interrupted f

    27、or weekends and holidays, in which case leave the samples in humidity for that period. 4.3.1.6.2 Required: See Table 1. 4.3.2 Functional Cycle Testing (if specified) 4.3.2.1 Method: Subject production intent samples to functional cycle testing as specified in engineering validation plan. All testing

    28、 shall be completed on actual modules or holding fixtures made to simulate modules. 4.3.2.2 Required: Upon completion of all testing, there shall be no evidence of any structural or adhesive failure. TABLE 2: SUBSTRATES ITEM DESCRIPTION SPECIFICATION DESCRIPTION 1 E-coat CEMS G-5 Part V Grade -56 Ca

    29、thodic E-coat BASF U32 2a Laminated Glass TMS-9522 Windshield, drop glass 2b Tempered Glass TMS-9522 Side, back and drop glass 3 Anodized 6063-T6 Aluminum CEMS C-10 Cab TABLE 3: CURE CYCLES ITEM DESCRIPTION CYCLE A1 Ambient Cure Follow and report manufacturers recommended practice. TABLE 4: MATERIAL

    30、S AND GENERAL PROPERTIES ID SUPPLIER/ MATERIAL CODE VISCOSITY Kcps OPEN TIME* 23 C Minutes COLOR A1 Dow Automotive Urethane BETAMATE 73100 10-30 4-6 Dark gray BETAMATE 73005 10-30 Light tan *Note Open Time refers to the interval of time between the spreading of the adhesive on the adherent and the c

    31、ompletion of the assembly of the parts for bonding. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is

    32、restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 5 of 7 TABLE 5: APPROVED MATERIAL (1), SUBSTRATE AND CURE CYCLE MATERIAL SYSTEM(S) (s

    33、ee Table 4) SUBSTRATE(S) (see Table 2) CURE CYCLE(S) (see Table 3) QUALIFIED SHEAR STRENGTH (see Table 1) MPa psi APPROVAL LEVEL/ REPORT NUMBER (2) COMMENTS A1 2b, 3 A1 2.1 (305) A (1)Only material and substrate combinations listed in this table are considered “Approved.” New material combinations m

    34、ay be approved by letter or report until specification updates are made. (2) Approval levels are as follows: Navistar Report number Full approval as documented in the Navistar report. A Grandfathered approval. Current production applications are required to submit test reports to this specification

    35、to maintain approvals. B Approved for prototypes and pre-production applications. 5.0 QUALIFICATION Material and processes submitted for approval to this specification shall include the following: 5.2.1 A detailed, signed test report documenting testing to this specification prepared per TMS-9543. 5

    36、.2.2 Test coupons or photographs showing failure modes for each test 5.2.3 The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test coupons. 5.2.4 Adhesive, substrate and any chemicals used for bonding. Note: Questions regardin

    37、g qualification requirements, reports and test materials shall be directed to: Manager of Non-Metallic Materials Materials Engineering and Technology Development Truck Development and Technology Center PO Box 1109 Fort Wayne, IN 46801 MaterialsE 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier R

    38、equirements All suppliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers mu

    39、st maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitte

    40、d without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar

    41、 Inc. DECEMBER 2009 Page 6 of 7 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In t

    42、he event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center, and Navistar Purchasing and Supplier Development of the proposed change(s). Tes

    43、t data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform

    44、and/or report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant

    45、metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing and identification shall be in accordance with Manufacturing Std. MS-D-13. 8.0 DESIGNATION ON D

    46、RAWINGS The drawing designation may be written in a general or specific manner depending on the requirements of the situation. The specification for a bonded assembly may be written as: Bond per TMS-6930 9.0 TECHNICAL INFORMATION For further information related to the technical content of this speci

    47、fication, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80

    48、112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 10.0 APPROVED SOURCES Dow Automotive Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6930 TITLE Glass Assembly Adhesive REVISION: 0912 This document is restricted and may not be se


    注意事项

    本文(INTERN TMS 6930-2009 Glass Assembly Adhesive《玻璃总成粘合剂》.pdf)为本站会员(tireattitude366)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开