欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    INTERN CEMS D-18-2009 Gasketing Materials Includes Appendix《衬垫材料 包含附录》.pdf

    • 资源ID:785857       资源大小:239.98KB        全文页数:14页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    INTERN CEMS D-18-2009 Gasketing Materials Includes Appendix《衬垫材料 包含附录》.pdf

    1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 1 of 9 NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECIFI

    2、CATION) NUMBER: CEMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE: April 2009 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: December 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve ha

    3、zardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notic

    4、e: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. 1.0 SCOPE This specification covers requirements for nonmetallic, non-asbestos gasketing materials used in products manufactured by the Company. Rub

    5、ber gasket materials are also specified in Engine Material Specification (EMS) D15-5010. 2.0 INTRODUCTION Materials covered by this specification are intended for use with coolants, fuel, lubricating oil, hydraulic fluid, brake fluid, refrigerants and air. 2.1 Restricted Chemical Substances Effectiv

    6、e January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 CONTENTS PAGE REFERENCE DOCUMENTS 1 CLASSIFICATION AND GRADE DESIGNATION 2 GENERAL REQUIREMENTS 2 QUALITY 6 METHODS OF TEST 8 SOURCE APPROVAL AND QU

    7、ALITY CONTROL 9 DESIGNATON ON DRAWINGS AND PURCHASE ORDERS 9 PACKING AND SHIPPING 9 APPENDIX Green Sheets CEMS D-18s APPROVED SOURCES (Restricted Issue) Orange Sheet 4.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following specificati

    8、ons, standards, and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 Engine Material Specification D15-5010 NAVISTAR Manufacturing Standard MS-D-13 Engine Material Specification D15-5011 NAVISTAR Engineering Design Standard A-16 Engine Material Specifica

    9、tion D18-5008 CFR Title 29, Part 1910 ASTM F104 NAVISTAR CEMS B-50 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE:

    10、 April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 2 of 9 5.0 CLASSIFICATION AND CONSTRUCTION Gaskets are

    11、 classified by grade as shown in Table 1 below. The last digit of the grade indicates the recommended upper temperature limits (Example 203 = 300F150C, 206 = 600F315C). Many factors influence a materials temperature resistance in an application. Engine Material Specification D18-5007 converts direct

    12、ly to this specification. Table 1 - Grade Classification GRADE OBSOLETE NAVISTAR GRADE MATERIAL DESCRIPTION RECOMMENDED UPPER TEMPERATURE LIMIT C F 102 10 Cork and Rubber 100 212 (1) 11 Rubber 100 212 122 12 or 10 Cork and Rubber 100 212 203 20 Non-metallic, non-asbestos 150 302 206 20 Non-metallic,

    13、 non-asbestos 315 600 303 30 Non-metallic, non-asbestos 150 302 306 30 Non-metallic, non-asbestos 315 600 406 40 Non-metallic, non-asbestos 315 600 413 41 Non-metallic, non-asbestos 150 302 416 41 Non-metallic, non-asbestos 315 600 (1) Contact Materials Engineering for appropriate replacement produc

    14、t. 6.0 GENERAL REQUIREMENTS The requirements are based on sheets of material and/or sheets coated with specific release coatings. Product supplied will meet requirements for the grade specified as shown in Table 2. 6.1 Lamination Lamination is permitted only when the process has the approval of Mate

    15、rials Engineering and only for combining two thicknesses to produce a sheet greater than the unlaminated thickness. Approval of the lamination process is based on the combined sheet meeting all of the following requirements: 6.1.1 Must have same physical strength characteristics as the single thickn

    16、ess sheet. 6.1.2 Must have the same fluid resistance as single thickness sheet. 6.1.3 Must have same aging characteristics as single thickness sheet. 6.1.4 Must not delaminate at the bond line. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo rep

    17、roduction or networking permitted without license from IHS-,-,-NUMBER: CEMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE: April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are require

    18、d to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 3 of 9 Table 2 - Gasket Properties GRADE 102 122 133 203 203 Supplier Code 3 1 1 Material Code E B B Gasket Thickness mm(in.) 1.6(.062) .25(.010) .79(.031) (1) Compressibility, % 30-55 30-50 40-60 15-25 14-24 (1) Recovery, % mi

    19、n. 75 75 15 30 30 (1) Density, kg/m3 (lb/ft3), min. 497(31) 513(32) 609(38) 1280(80) 1250(78) (1) Tensile Strength, MPa (psi), min. .96(140) 1.4(200) 1.5(220) 6.9(1000) 6.9(1000) (2) Creep Relaxation, % max. - - - 15 30 Immersion Change in Volume, % (1) ASTM Fuel A -2 to +15 -2 to +10 - 0 to +15 0 t

    20、o +15 (2) ASTM #1 Oil 10 10 - 0 to +10 0 to +10 (1) ASTM #3 Oil (IRM903) 0 to +45 0 to +30 0 to +45 0 to +15 0 to +15 (2) Distilled Water (by weight) max. - - 40 0 to +25 0 to +25 Distilled Water/ Ethylene Glycol (1:1 By Volume) - - - 0 to +30 0 to +30 (2) Sealability, ml/h, max. - - - - - (2) Flexi

    21、bility - No cracks, breaks or separations Pass Pass Pass Pass Pass (2) Adhesion - - - - - (2) Dimensional Stability - - - - - (2) Crush Extrusion - - - - - Comments To be used with EMS D15-5011 To be used with EMS D15-5011 (1) Properties to be used for batch certification. (2) Properties to be used

    22、for periodic re-certification (annually or better). 6.2 Release Coatings 6.2.1 Material supplied to this specification may require a release coating in order to meet the adhesion requirement. 6.2.2 The release coating must not cause corrosion on flanges. 6.3 Mechanical and Physical Properties See th

    23、e appropriate table for each grade. Material supplied to this specification may require a release coating in order to meet the adhesion requirement. Some properties are designated as typical values. Material will not be rejected on typical properties. The NAVISTAR receiving plants quality department

    24、 will request the supplier to furnish data on typical properties within one year of furnishing material. Data is to be forwarded to Materials Engineering for incorporation into this specification. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo

    25、reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE: April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are requ

    26、ired to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 4 of 9 Table 2 - Gasket Properties - Continued GRADE 203 203 203 203 203 203 Supplier Code 1 1 2 2 2 2 Material Code A F A A A A Gasket Thickness mm(in.) .79(.031) .38(.015) .41(.016) .79(.031) 1.2(.047) 1.6(.062) (1) Compre

    27、ssibility, % 15-25 10-20 (3) 15-25 15-25 15-25 15-25 (1) Recovery, % min. 35 30 35 35 35 35 (1) Density, kg/m3(lb/ft3), min. 1300(81) 1120(70) 1200(75) 1200(75) 1200(75) 1200(75) Tensile Strength, MPa(psi), min. 6.9(1000) 5.2 (750) 9.6(1400) 9.6(1400) 9.6(1400) 9.6(1400) (2) Creep Relaxation, % max.

    28、 30 16 20 35 40 50 Immersion Change in Thickness, % (2) ASTM Fuel B 0 to +15 0 to +10 0 to +15 0 to +15 0 to +15 0 to +15 (2) ASTM #1 Oil 0 to +10 0 to +10 1.0* 1.0* 1.0* 1.0* (1) ASTM #3 Oil (IRM903) 0 to +15 0 to +10 0 to +15 0 to +15 0 to +15 0 to +15 (2) Distilled Water 0 to +15 0 to +15 +7.3* +

    29、7.3* +7.3* +7.3* Distilled Water/ Ethylene Glycol(1:1 By Volume) 0 to +15 0 to +15 +7.7* +7.7* +7.7* +7.7* (2) Sealability, ml/h, max. - - - - - - (2)Flexibility - No cracks, breaks, or separations or Separations Pass Pass Pass Pass Pass Pass (2) Adhesion Pass - Pass Pass Pass Pass (2) Dimensional S

    30、tability - - - - - - (2) Crush Extrusion - - - - - - Comments To Be Used with Grade 1 EMS D18-5008 *Typical Results *Typical Results *Typical Results *Typical Results (1) Properties to be used for batch certification. (2) Properties to be used for periodic re-certification (annually or better). (3)

    31、17 MPa (2500 psi) 6.4 Dimensional Tolerances Material supplied to this specification shall meet the following thickness tolerances unless otherwise specified on the drawing. NOMINAL THICKNESS mm(inches) TOLERANCE mm(inches) .25(.010) +.025/-.025(+.001/-.001) .38(.015) +.05/-.05(+.002/-.002) .51(.020

    32、) +.05/-.05(+.002/-.002) .79(.031) +.13/-.13(+.005/-.005) 1.2(.047) +.13/-.13(+.005/-.005) 1.6(.062) +.2/-.2(+.008/-.008) Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: C

    33、EMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE: April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page

    34、 5 of 9 Table 2 - Gasket Properties - Continued GRADE 203 203 206 303 303 303 Supplier Code 3 6 3 1 1 1 Material Code A A H D D D Gasket Thickness mm(in.) .79(.031) .79(.031) .79(.031) .38(.015) .51(.020) .79(.031) (1) Compressibility, % 15-30 15-25 15-30 7-17 7-17 7-17 (1) Recovery, % min. 35 35 25

    35、 40 40 40 (1) Density, kg/m3(lb/ft3), min. 1200(75) 1200(75) 1280(80) 1400(88) 1400(88) 1400(88) Tensile Strength, MPa(psi), min. 11(1600) 12(1800) 1.0(1500) 13.8(2000) 13.8(2000) 13.8(2000) (2) Creep Relaxation, % max. 40 35 45 25 30 35 Immersion Change in Thickness, % (2) ASTM Fuel B 0 to +10 0 to

    36、 +15 0 to +20 0 to +15 0 to +15 0 to +15 (2) ASTM #1 Oil 0 to +5 0 to +15 0 to +10 0 to +10 0 to +10 (1) ASTM #3 Oil (IRM903) 0 to +15 0 to +10 0 to +20 0 to +13 0 to +13 0 to +13 (2) Distilled Water 0 to +20 0 to +20 0 to +10 0 to +25 0 to +25 0 to +25 Distilled Water/Ethylene Glycol (1:1 By Volume

    37、) 0 to +30 10 to +20 0 to +35 0 to +30 0 to +30 0 to +30 (2) Sealability, ml/h, max. - - - - - - (2) Flexibility - No cracks, breaks or Separations Pass Pass Pass Pass Pass Pass (2) Adhesion Pass Pass Pass (100) - - - (2) Dimensional Stability - - - - - - (2) Crush Extrusion - - - - - - Comments To

    38、be used with EMS D18-5011 To be used with EMS D18-5011 To be used with Grade 2 EMS D18-5008 (1) Properties to be used for batch certification. (2) Properties to be used for periodic re-certification (annually or better). 6.5 Lot Definition Properties are to be used for qualification of material as w

    39、ell as for certification of each batch of incoming material. A batch is defined as all parts made from material formulated at one time. Shipping containers are to show batch numbers. Batches shall not be mixed in any one box, but a lot may contain more than one batch. 7.0 QUALITY All material and wo

    40、rkmanship shall be in accordance with good commercial practice and the resulting product shall be free from defects detrimental to fabrication or use. Suppliers shall furnish infrared spectra for the sheet material used in the manufacture of qualification samples. Copyright Navistar International Co

    41、rporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS D-18 TITLE: Gasketing Materials CURRENT ISSUE DATE: April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced witho

    42、ut permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 6 of 9 Table 2 - Gasket Properties - Continued GRADE 306 306 306 306 306 Supplier Code 1 1 1 4 7 Material Code E E E J K Gasket Thickness mm(in.) .38(.015)

    43、.51(.02) .79(.031) .79(.031) .79(.031) (1) Compressibility, % 7-17 7-17 7-17 7-17 8-20 (1) Recovery, % min. 50 50 50 50 40 (1) Density, kg/m3(lb/ft3), min. 1460(91) 1460(91) 1460(91)(1) 1520(95) 1390(87) Tensile Strength, MPa(psi), min. 17(2500) 17(2500) 17(2500) 14(2000) 16(2300) (2) Creep Relaxati

    44、on, % max. 18 22 25 25 25 Immersion Change in Thickness, % 0 to +15 0 to +15 0 to +15 0 to +10 0 to +10 (2) ASTM Fuel B 0 to +10 0 to +10 0 to +10 0 to +5 0 to +10 (2) ASTM #1 Oil (1) ASTM #3 Oil (IRM903) 0 to +15 0 to +15 0 to +15 0 to +15 0 to +10 (2) Distilled Water 0 to +10 0 to +10 0 to +10 0 t

    45、o +10 0 to +10 Distilled Water/ Ethylene Glycol (1:1 By Volume) 0 to +15 0 to +15 0 to +15 0 to +15 0 to +10 (2) Sealability, ml/h, max. - - - - - (2) Flexibility - No cracks, breaks or Separations Pass Pass Pass Pass Pass (2) Adhesion - - Pass Pass Pass (2) Dimensional Stability - - - - - (2) Crush

    46、 Extrusion - - - - - Comments To be used with EMS D15-5011 To be used with EMS D15-5011 To be used with EMS D15-5011 (1) Properties to be used for batch certification. (2) Properties to be used for periodic re-certification (annually or better). 7.1 Quality Control Plan A Quality Control Plan for th

    47、is product will be established by mutual agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as features for management by statistical process control.* 1 . T h ick n e s s 2 . C o m p r es s ib il it y KCC * Other Characteristics for inclusion in the control plan may be specified o


    注意事项

    本文(INTERN CEMS D-18-2009 Gasketing Materials Includes Appendix《衬垫材料 包含附录》.pdf)为本站会员(terrorscript155)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开