1、ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2485 1 of 2 September, 2006June, 2007 NAME: LUBRICANT REAR AXLE, FULL SYNTHETIC, SAE 75W-85 API GL5 THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS
2、 THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:Material SpecificationStandardFormsMaterialSpecificationMatspec.doc 1. SCOPE This material specification describes properties of initial fill synthetic hypoid gear oil that is recommended for use in specific ve
3、hicle applications nominated by the responsible design engineer. Note: HN 2485 is also known as GM Holden Part Number 92184900. 2. REFERENCES HN 1000 ASTM D1298 ASTM D445 ASTM D2270 ASTM D92 ASTM D97 ASTM D892 ASTM D2983 GMW3059 3. TYPICAL PROPERTIES Density at 15C (kg/m3) 862 ASTM D1298 Viscosity a
4、t 40C (mm2/s) 60.6 ASTM D445 Viscosity at 100C (mm2/s) 11.5 ASTM D445 Viscosity Index 188 ASTM D2270 Brookfield Viscosity at -40C (mPa.s) 80,400 ASTM D2983 Pour Point (C) -57 ASTM D97 Flash Point (C) 222 ASTM D92 Foam seq. I/II/III (ml) 0/5/0 ASTM D892 4. APPROVAL, INSPECTION AND REJECTION Refer HN
5、1000, Clauses A and C. 5. HAZARDOUS MATERIALS Refer HN 1000, Clause H. ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2485 2 of 2 September, 2006June, 2007 NAME: LUBRICANT REAR AXLE, FULL SYNTHETIC, SAE 75W-85 API GL5 THIS DOCUME
6、NT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:Material SpecificationStandardFormsMaterialSpecificationMatspec.doc 6. RESTRICTED AND REPORTABLE SUBSTANCES (i) All substances and parts mu
7、st meet the requirements of GMW3059. (ii) All chemical components present in materials supplied to this specification must comply with Australian NICNAS (National Industrial Chemicals Notification and Assessment Scheme) obligations. 7. APPROVED SUPPLIERS AND MATERIALSMaterial known to meet the full
8、requirements of this specification: APPROVED SUPPLIER APPROVED MATERIAL Castrol Castrol SAF Carbon Mod. 8. REVISIONS November, 2006 - Section “1.SCOPE” - added that HN 2485 is also known as GM Holden Part Number 92184900 February, 2007 -Section “3 TYPICAL PROPERTIES” - Revised the values listed for
9、“Density at 15C”, “Viscosity at 40C”, “Viscosity at 100C”, “Viscosity Index”, “Brookfield Viscosity at -40C”, “Flash Point”, and “Foam seql/ll/lll”. -Section “7 APPROVED SUPPLIERS AND MATERIALS” - Approved material replaced with Castrol SAF Carbon Mod Plus June, 2007 -Section “3 TYPICAL PROPERTIES”
10、- Revised the values listed for “Density at 15C”, “Viscosity at 40C”, “Viscosity at 100C”, “Viscosity Index”, “Brookfield Viscosity at -40C”, “Flash Point”, and “Foam seql/ll/lll”. -Section “7 APPROVED SUPPLIERS AND MATERIALS” - Approved material replaced with Castrol SAF Carbon Mod Prepared by: Maria Lasic
