欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW16998-2013 Dust-Out From Fiber Sound Absorber Pad Issue 1 English.pdf

    • 资源ID:757963       资源大小:153.33KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW16998-2013 Dust-Out From Fiber Sound Absorber Pad Issue 1 English.pdf

    1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW16998 Dust-Out From Fiber Sound Absorber Pad Copyright 2013 General Motors Company All Rights Reserved September 2013 Page 1 of 3 1 Scope Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict betwe

    2、en the English and domestic language, the English language shall take precedence. 1.1 Purpose. This procedure describes a method for measurement of dust-out from fiber sound absorber pad. It applies to both needled and resin-bonded constructions and to unfaced as well as coated and film-covered mate

    3、rials. 1.2 Foreword. Not applicable. 1.3 Applicability. This procedure is intended for use in assembly plants and/or production quality control. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 17025 ISO/TS 16

    4、949 2.2 GM Standards/Specifications. None 2.3 Additional References. None 3 Resources 3.1 Facilities. Facilities must be certified to ISO 17025 and/or certified to ISO/TS 16949 and be acceptable to the responsible GM department. Supplier shall submit a letter of compliance. 3.1.1 Calibration. The te

    5、st facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their phys

    6、ical definition. 3.2 Equipment. 3.2.1 Cutting dye, 50 mm x 50 mm. 3.2.2 Cutting press. 3.2.3 Coated metal can with lid. 3.2.4 Air-circulating oven. 3.2.5 Balance that weighs in grams. 3.2.6 Low-pressure air line with nozzle opening 5 mm 0.5 mm. 3.2.7 Isopropyl alcohol. 3.2.8 Lint-free cloth. 3.3 Tes

    7、t Vehicle/Test Piece. 3.3.1 Cut four (4) specimens using cutting press and cutting dye to 50 mm x 50 mm. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERI

    8、NG STANDARDS GMW16998 Copyright 2013 General Motors Company All Rights Reserved September 2013 Page 2 of 3 Note: Do not disturb or remove any loose fibers or dust from samples after cutting. 3.4 Test Time. Not applicable. 3.5 Test Required Information. Not applicable. 3.6 Personnel/Skills. Not appli

    9、cable. 4 Procedure 4.1 Preparation. 4.1.1 Place the four (4) test specimens in an air-circulating oven at 100 C for 1 h. 4.1.2 After 1 h at 100 C, remove specimens and immediately weigh each specimen to the nearest 0.01 g. 4.1.3 Moisten lint-free cloth with alcohol and wipe the inside of the metal c

    10、an. Allow can to dry for 15 minutes. 4.1.4 Place four (4) specimens in the can and seal with lid. 4.1.5 Shake the can 150 times 2 times within 60 s. 4.1.6 Remove the specimens from the can. Holding the low-pressure air nozzle about 200 mm from each of the specimens, gently blow all loose material fr

    11、om the specimens. 4.1.7 Place the four (4) specimens in an air-circulating oven for 1 h at 100 C. 4.1.8 After 1 h at 100 C, remove specimens and weigh each to the nearest 0.01 g. 4.2 Conditions. 4.2.1 Environmental Conditions. Not applicable. 4.2.2 Test Conditions. Deviations from the requirements o

    12、f this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. Not applicable. 5 Data 5.1 Calculations. 5.1.1 Calculate the percent dust loss on each specimen per the following equation: 5.2 Interpretation o

    13、f Results. Not applicable. 5.3 Test Documentation. Not applicable. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to es

    14、tablish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. GSSLT Global Subsystem Leadership Team ISO International Organization for Standardization I ni t i a

    15、l W ei gh t F i na l W ei gh t% D ust = _ _ _ _ _ x 100 I ni t i al W ei ghtCopyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16998 Copyrig

    16、ht 2013 General Motors Company All Rights Reserved September 2013 Page 3 of 3 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW16998 9 Release and Revisions This standard was originated in June 2013. It was first approved by the Trim Materi

    17、als/Textiles/Leather/Foam Global Subsystem Leadership Team (GSSLT) in September 2013. It was first published in September 2013. Issue Publication Date Description (Organization) 1 SEP 2013 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(GMW GMW16998-2013 Dust-Out From Fiber Sound Absorber Pad Issue 1 English.pdf)为本站会员(周芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开