1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW16912 Literature Material Testing for Cover - Owners Info Manual (i.e., Folder/Wallet/Pouch) Copyright 2013 General Motors Company All Rights Reserved July 2013 Page 1 of 3 1 Introduction Note: Nothing in this standard supercedes applicable l
2、aws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Scope. This standard establishes the common technical requirements for the literature commodity for the folder/wallet/pouch for a GM vehicle sold worldwide.
3、The common functions, performance, design constraints, reliability, and validation required of the subsystem are defined in this document. This specification becomes Statement of Requirements (SOR) Appendix C1 to a SOR for the literature subsystem. 1.2 Mission/Theme. The primary purpose is to provid
4、e a convenient, attractive folder/wallet/pouch to “hold” customer literature. 1.3 Classification. Not applicable. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 105-X12 2.2 GM Standards/Specifications. GMW30
5、59 GMW3232 GMW14124 GMW15634 GMW3205 GMW3235 GMW14126 GMW16853 2.3 Additional References. Appendix C1 GM Ergonomic Guidelines SOR for the Literature Subsystem 3 Requirements 3.1 System/Subsystem/Component/Part Definition. The folder/wallet/pouch provides a convenient, attractive “holder” for the cus
6、tomer literature. Parts should not have burrs or sharp angles; distortion, or scrapes in the parts surface. The color of part should be consistent. There shall be no visible sink marks on literature components, for textile, leather and other decorative materials: no wrinkles allowed in visible areas
7、. 3.1.1 Appearance. The folder/wallet/pouch shall maintain appearance, shape, color, texture, fit and alignment over the target life of the vehicle. 3.1.2 Content. The folder/wallet/pouch strategy is approved by the marketing organization, usually with consistent direction for the vehicle nameplate.
8、 The required physical and functional requirements for the cover/wallet/pouch are identified in the following paragraphs. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WO
9、RLDWIDE ENGINEERING STANDARDS GMW16912 Copyright 2013 General Motors Company All Rights Reserved July 2013 Page 2 of 3 3.1.3 Ambient Environment. The preferred storage location for the folder/wallet/pouch containing customer literature is in the glove box. Alternative storage locations, such as the
10、center console, map pocket, or trunk, require program team approval. 4 Validation 4.1 General. Validation consists of test, inspections, analysis, and demonstrations to ensure that the folder/wallet/pouch meets all requirements (See Table 1). All validation tests shall be performed on production int
11、ent parts and are the responsibility of the supplier. Table 1: Required Validation Tests Number Test Name Test Part Required Test Output/Target Value 1 Automotive Environmental Cycles (Dimensional Stability) GMW14124 5 Cycles M, at high temperature (85 C) Dimensional Change: - Longitudinal Direction
12、 - Transverse Direction Wallet/Pouch/Cover Must show no quality defects like: mold build-up, warping, maceration mildew, wrinkles, striations, or scrapes. 2 Resistance to Cold Crack of Folded Materials GMW14126 Wallet/Pouch/Cover No Visible Breaks 3 Color Fastness to Rubbing ISO 105-X12 Wallet/Pouch
13、/Cover Rating Four (4) minimum 4 Flammability of Interior Trim Materials GMW3232 Per Zone B to Self-Extinguishing (SE) Wallet/Pouch/Cover Self-Extinguishing 5 Emission Tests Per GMW16853 - Volatile Organic Compound/ Semi-Volatile Organic Compound (VOC/SVOC) - Fogging - Odor GMW15634 GMW3235 Method B
14、, Temp T2 GMW3205 Condition A3 and B3 Wallet/Pouch/Cover Report values 2.0 mg maximum (no droplets or crystals) Rating Six (6) minimum 6 Restricted and Reportable Chemicals GMW3059 Wallet/Pouch/Cover Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for Re
15、saleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16912 Copyright 2013 General Motors Company All Rights Reserved July 2013 Page 3 of 3 4.2 Validation Cross Reference Index. Not applicable. 4.3 Supporting Paragraphs. Not applicable. 5 Prov
16、isions for Shipping 5.1 The anticipated shipping and storage conditions relative to temperature and humidity are: 90 C to -40 C for temperature range and a maximum 95% relative humidity. 5.2 The folder/wallet/pouch shall be packed in order to avoid part damage during shipping and storage. A containe
17、r of literature parts shall not weigh in excess of ergonomic guidelines specified by GM. Note: These are shipping conditions, which are unique and could be more severe than the environment inside a vehicle. These conditions must be anticipated and designed for when designing folder/wallet/pouch ship
18、ping containers. 6 Notes 6.1 Glossary. Not applicable. 6.2 Acronyms, Abbreviations, and Symbols. SE Self-Extinguishing SOR Statement of Requirements SVOC Semi-volatile Organic Compound VOC Volatile Organic Compound 7 Additional Paragraphs 7.1 All parts or systems supplied to this standard must compl
19、y with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: GMW16912. 9 Release and Revisions This standard was originated in January 2013. It was first approved by the Interior
20、- Labels and Literature GSSLT in July 2013. It was first published in July 2013. Issue Publication Date Description (Organization) 1 JUL 2013 Initial publication. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
