欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW15284-2011 Spot Test for Etch Susceptibility of Stainless Steel Issue 2 English《不锈钢的刻蚀敏感性现场试验 第2次出版(英文版本)》.pdf

    • 资源ID:757636       资源大小:37.20KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW15284-2011 Spot Test for Etch Susceptibility of Stainless Steel Issue 2 English《不锈钢的刻蚀敏感性现场试验 第2次出版(英文版本)》.pdf

    1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW15284 Spot Test for Etch Susceptibility of Stainless Steel Copyright 2011 General Motors Company All Rights Reserved September 2011 Originating Department: North American Engineering Standards Page 1 of 2 1 Scope Note: Nothing in this standard super

    2、cedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This standard describes a test procedure to be followed when conducting spot test on cold rolled stainless steel. The object of th

    3、e test is to determine etch susceptibility on the stainless steel. 1.2 Foreword. Not applicable. 1.3 Applicability. Not applicable. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ASTM D1193 2.2 GM Standards/Spec

    4、ifications. None 2.3 Additional References. None. 3 Resources 3.1 Facilities. Not applicable. 3.2 Equipment. 3.2.1 Test Solution. The following reagent grade chemicals are dissolved in 200 ml of deionized water: x 10 g ferric chloride (hydrated) (Fe3CI 6H20) x 5 g sodium chloride x 2.5 mL hydrochlor

    5、ic acid (concentrated) x Deionized water (per ASTM D1193 Type IV) Note: This test solution must be stored in a stoppered glass container and used within 1 month of initial mixing. 3.2.2 Solvent. Suitable organic solvents or detergents for cleaning specimens. 3.2.3 Drying. A sufficient amount of soft

    6、 clean cloth or paper towels for drying specimens. 3.2.4 Dropper. A clean glass dropper. 3.2.5 Container. A clean glass container (for immersion testing when required). 3.3 Test Vehicle/Test Piece. Coupons of incoming material or parts manufactured from stainless steel are satisfactory for the test.

    7、 For Production Part Approval Process, actual production parts are to be used. 3.4 Test Time. Not applicable. Calendar time: days Test hours: hours Coordination hours: hours 3.5 Test Required Information Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. The stainless

    8、 steel surface shall be cleaned of oil, wax, dirt or buffing compound by means of organic solvents or detergents, followed by a tap water rinse and drying with a paper towel. 4.1.1 Wash samples in Alconox or comparable detergent solution to achieve as near a water break-free surface as possible, i.e

    9、., scrub samples with nylon brush; soak samples 20 to 30 minutes; re-scrub samples; re-soak samples 5 additional minutes using an Alconox solution 8 g/L, 43 2 C. Rinse cleaned samples, each with fresh room temperature 25 5 C water. 4.1.2 Immediately examine samples visually for any pits, scratches,

    10、roughness or other defects and record. Then begin test again within 1 minute of cleaning. 4.2 Conditions. The sample and test temperature solution should be maintained between 25 5 C during testing. 4.2.1 Environmental Conditions. Not applicable. 4.2.2 Test Conditions. Deviations from the requiremen

    11、ts of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permit

    12、ted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15284 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 2 of 2 4.3.1 Application of Solution. Test solution must be applied in the following way: Apply a drop with a clean glass dropper in a 6 to 8 mm

    13、diameter wax ring made with a china pencil or comparable wax marking device. 4.3.2 Duration of Test. The solution shall be left in contact with the surface of the sample for 5 minutes. The solution shall be removed by rinsing with flowing tap water, and the surface dried with forced air or by light

    14、rubbing with a clean soft cloth or paper towel. The wax ring shall be removed with an organic solvent. Test-to-failure should be done in additional 5 minute increments. 5 Data 5.1 Calculations. Not applicable. 5.2 Interpretation of Results. 5.2.1 Etch susceptibility is determined by visual compariso

    15、n of the test spot with untested surface areas. Etch susceptibility is indicated by various degrees of dulling, frosting, pitting, graying, or any other type of visible permanent change in luster of the test area. Samples should be viewed under daylight as well as fluorescent lighting. 5.2.2 Accepta

    16、nce criteria shall be specified within engineering documentation which includes: Material Specifications, Subsystem Technical Specifications, Component Technical Specification, and Part Drawings. 5.3 Test Documentation. Document the etch susceptibility as described in 5.2.1. 6 Safety This standard m

    17、ay involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulato

    18、ry limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW15284 9 Release and Revisions This standard was originated in Marc

    19、h 2005. It was first approved by the Global Laboratory Corrosion testing Harmonization Team in April 2006. It was first published in August 2006. Issue Publication Date Description (Organization) 1 AUG 2006 Initial publication. 2 SEP 2011 Five year refresh. Term “distilled water” replaced by deionized water; Paragraph 3.2.1. ASTM D1193 Type IV for deionized water added. (Corrosion Global Sub-system Leadership Team) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(GMW GMW15284-2011 Spot Test for Etch Susceptibility of Stainless Steel Issue 2 English《不锈钢的刻蚀敏感性现场试验 第2次出版(英文版本)》.pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开