欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW15184-2013 Spring Hose Clamp Issue 3 English.pdf

    • 资源ID:757623       资源大小:237.77KB        全文页数:12页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW15184-2013 Spring Hose Clamp Issue 3 English.pdf

    1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW15184 Spring Hose Clamp Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 1 of 12 1 Scope This standard covers the materials and performance requirements for spring band hose clamps. Spring band hose clamps must functi

    2、on with hose/nipple connections of a variety of dimensional ranges and must have a full open diameter which is large enough to install the hose clamp over a bead when the hose clamp is already assembled. Clamp size will be designated by its Nominal Diameter (Dn) to distinguish between different hose

    3、 clamp working ranges. 1.1 Material Description. The material used is an austempered carbon steel. Generally, a coating per GMW14083 is applied for resistance against corrosion and general automotive fluids. 1.2 Symbols. Not applicable. 1.3 Typical Applications. This specification covers five types

    4、of Constant Tension Band (CTB) Clamps: Type A: Normally Closed, Regular Profile (see Figure 1). Type B: Pre-opened with Clip, Regular Profile (see Figure 2). Type C: Pre-opened Clipless (see Figure 3). Type D: Normally Closed, Low Profile (Space Saver) (see Figure 4). Type E: Pre-opened with Clip, L

    5、ow Profile (Space Saver) (see Figure 5). Figure 1: Clamp Type A, Normally Closed, Regular Profile (see Figure A1 for specifications) Figure 2: Clamp Type B, Pre-opened with Clip, Regular Profile (see Figure A2 for specifications) Copyright General Motors Company Provided by IHS under license with Ge

    6、neral Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 2 of 12 Figure 3: Clamp Type C, Pre-opened Clipless (see Figure A3 for specifica

    7、tions) Figure 4: Clamp Type D, Normally Closed, Low Profile (Space Saver) (see Figure A4 for specifications) Figure 5: Clamp Type E, Pre-opened with Clip, Low Profile (Space Saver) (see Figure A5 for specifications) 2 References Note: Only the latest approved standards are applicable unless otherwis

    8、e specified. 2.1 External Standards/Specifications. ASTM E18 EN 10083-1 ASTM E140 SAE J403 EN 10132-4 SAE J404 2.2 GM Standards/Specifications. GMW3059 GMW14083 2.3 Additional References. TMC003 Material Safety Data Sheet guidance documents (available at ). 3 Requirements 3.1 Material. The hose clam

    9、ps may be produced from either cold rolled chromium-vanadium alloy steel or SAE J403 Grades 1074 and 1075 or JIS Grade SK5. See Table 1 for acceptable materials.Table 1: Steel Grades Standard Chemical Composition EN 10132-4 51CrV4 C: 0.50 to 0.55 Mn: 0.8 to 1.1 V: 0.1. to 0.25 EN 10132-4 C75S Option

    10、al: Cr: 0.15 to 0.40 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June

    11、 2013 Page 3 of 12 Standard Chemical Composition EN 10083-1 50CrV4 C: 0.47 to 0.55 Mn: 0.7 to 1.10 V: 0.1 to 0.25 SAE J404 Grade 6150 SAE J404 Grade 6150 modified C: 0.50 to 0.55 Mn: 0.8 to 1.1 V: 0.1. to 0.2 SAE J403 Grade 1074 - SAE J403 Grade 1075 Optional: Cr: 0.15 to 0.40 JIS Grade SK5 C (0.80

    12、to 0.90), Si (Max. 0.35), Mn (Max. 0.5), P (Max. 0.03), S (Max. 0.03), Cr (Max. 0.3), Cu (Max. 0.25), Ni (Max. 0.25) Key:C = Carbon Cr = Chromium Cu = Copper Max. = Maximum Mn = Manganese Ni = Nickel Si = Silicon S = Sulfur V = Vanadium Grain flow of the metal must be in the longitudinal direction o

    13、f the part (see Figure 6). Phosphate-type coating as a processing aid for the manufacture of cold rolled steel band is not allowed. Figure 6: Clamp Shape and X-Y Directions of Hose Clamps 3.2 Material Hardness. 3.2.1 Clamps shall be austempered to a hardness of 470 to 580 HV10/HV30 or 47 to 54 HRC.

    14、3.2.2 Hardness shall be taken on the ground edge (side surface) after 0.3 mm cold grinding or on the tang, the side opposite the stamped number per ASTM E18. Note: For thinner material, use HR45N per ASTM E18 and convert results to HV or HRC values per ASTM E140. 3.3. Protective Coatings and Colors.

    15、 Hose clamps shall be coated per GMW14083 to prevent corrosion. 3.4 Dimensions, Closed and Full Open Diameter. See Figure 7 and Figure 8.Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license fro

    16、m IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 4 of 12 Figure 7: Example - Maximum Closed Diameter (D1) Figure 8: Example - Minimum Full Open Diameter (D2) 3.4.1 The hose clamps must meet the dimensional requirements as

    17、shown on the part drawings. 3.4.2 The closed diameter (D1) is to be measured in the X-direction (see Figure 6) by using a dial gage. 3.4.3 The full open diameter (D2) is to be measured on a step gage or gage pin with 0.1 mm increments. Note: The full open position occurs at an appropriate force when

    18、 the stop just contacts the opposite tang. Excessive force can distort the clamp and cause variation in clamp load and dimensions. 3.5 Dimensional Measurements. 3.5.1 Prior to measuring, the hose clamps must be opened to their full open diameter once for 5 s to 10 s. 3.5.2 It is important that clamp

    19、s are deflected evenly. This can be achieved only by using an appropriate tool that does not deform or damage parts during use. 3.5.3 Clamps Type B, C and E supplied in the pre-opened condition shall be released while the base is held in rubber padded jaw or over a mandrel. 3.5.4 A set of random sam

    20、ples (30 minimum) when tested shall meet a statistical spread with -3 sigma values greater than the D1 Maximum shown in Appendix A. 3.6 Performance Requirements. 3.6.1 Clamping Force. 3.6.1.1 Hose clamps shall meet minimum clamping forces as shown in Appendix A. Part sizes and styles not mentioned i

    21、n Appendix A are to be specified on individual part drawing or part catalog. 3.6.1.2 The testing frequency is to be determined by supplier with approval of GM. 3.6.1.3 Clamping Force Measurement. 3.6.1.3.1 The clamping force of the hose clamp must be measured on a three (3) segment load cell. 3.6.1.

    22、3.2 For submission of test data, a three segment tester that has been shown to correlate with the Master Tester at GM must be used. 3.6.1.3.3 Contact Fastening Engineering for information concerning this tester. 3.6.1.3.4 The load cell must be calibrated on frequency as per International Organizatio

    23、n for Standardization (ISO) certification requirements. 3.6.1.3.5 Clamps must be fully opened once (see 3.4.1) before being tested for clamping force. 3.6.1.3.6 The clamping force measurement shall be run on clamps of every individual heat lot of steel. 3.6.1.3.7 The supplier shall retain all test r

    24、ecords for a period of one year after date of test. Test reports shall be submitted to GM Engineering and Supplier Quality upon request. D 1D 2Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without licen

    25、se from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 5 of 12 Figure 9: Orientation of a Hose Clamp on a 3-Segment Load Cell 3.6.1.4 The clamping force must be measured at a diameter which corresponds to the nominal hose

    26、clamp size. If applicable due to force tester design, the force tester diameter shall be set up for each size using a ring gage of nominal diameter (Dn 0.05 mm) such that the average force preload is between 5 N and 15 N when the tester pins (rollers) are against the inside diameter of the ring gage

    27、. 3.6.1.5 The clamping force is the average of the three measured forces. 3.6.1.6 For repeatability of test, place the hose clamp on the load cell fixture by indexing the small arc between the tangs always at the same location (segment 1) with respect to the load cell segments as shown in Figure 9.

    28、Note: Load cells with additional segments may be used for clamp development purposes. 3.6.1.7 Clamping force measurement requirements are shown in Appendix A. 3.6.1.8 Pre-opened clamps shall be load tested (Development (DV) and Production Parts Approval Process (PPAP) only) after an exposure to ambi

    29、ent temperature of 23 C 5 C for 168 h in the pre-opened position. For Pre-opened clip or clipless clamps, the supplier must provide tooling required to release the clamp. 3.7 Roundness. When testing for roundness, there shall be no gap between the hose clamp and the plug gage greater than the follow

    30、ing: 0.12 mm for nominal sizes 50 mm 3.7.1 Roundness Test. For testing the roundness of a hose clamp, the clamp shall be assembled on a plug gage with a ground surface. Any gap between the hose clamp and the plug gage shall be measured with a feeler gage with a 3 mm maximum band width. 3.7.2 Dependi

    31、ng on the nominal hose clamp size, the Plug Gage Diameter (Dp) of the gage shall be as shown in Table 2. Table 2: Plug Gage Diameters for Roundness Tests Nominal Hose Clamp Size Dn, Millimeters Plug Gage Diameter Dp, Millimeters 35 Dp = Dn -0.6 3.8 Hydrogen Assisted Cracking Process Control Test. Th

    32、e following test shall be conducted regularly (three parts each lot at a minimum) on hardened and uncoated hose clamps as a process control test to ensure effective Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking p

    33、ermitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 6 of 12 austempering and avoidance of martensitic transformation in the material. The clamps are to be installed on a plastic mandrel and immerse

    34、d in a 0.9% HCl solution for 8 minutes. The diameter of the plastic mandrel must be 0.2 mm to 0.3 mm smaller than the minimum full open diameter of the clamp size. The clamps must withstand this test for 8 minutes without cracking or breakage. 3.9 Cold Cycle Test Development. The clamps must be able

    35、 to withstand five cycles of opening from the closed condition to the full open condition while at -40 C. Condition a minimum of five clamps at -40 C for 4 h. Immediately after removal from the conditioning chamber, cycle the clamps from the closed position to the full open position five times withi

    36、n 30 s. Any cracking or fracture of any clamp constitutes a failure. 4 Manufacturing Process Not applicable. 5 Rules and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of

    37、conflict between the English and domestic language, the English language shall take precedence. 5.3 Inspection and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by

    38、 the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial rel

    39、ease must be completed. It is the responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeat

    40、ed and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product su

    41、bmissions, or when a change in chemical composition of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other cou

    42、ntry-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.5 All materials supplied to this standard must comply with the requireme

    43、nts of GMW3059, Restricted and Reportable Substances for Parts. 6 Approved Sources Materials supplied to this specification must be approved by General Motors. A list of approved materials can be found in MATSPC. This GM Material File is provided to third parties to reduce redundant testing of mater

    44、ials. If approved material already listed is used, the part supplier can use GM Material File reference for Production Part Approval Process (PPAP) material approval. If the decision is made to use a not yet approved material, contact Global Materials Groupfor details on the approval process. The ma

    45、terial approval process must be completed prior to PPAP start date of the part supplied to General Motors. 7 Notes 7.1 Glossary. MATSPC: Global repository of GM approved materials for corresponding GM Engineering Standards. 7.2 Acronyms, Abbreviations, and Symbols. C Carbon Cr Chromium CTB Constant

    46、Tension Band Cu Copper D1 Closed Diameter D2 Full Open Diameter Dn Nominal Diameter Dp Plug Gage Diameter DV Development Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WOR

    47、LDWIDE ENGINEERING STANDARDS GMW15184 Copyright 2013 General Motors Company All Rights Reserved June 2013 Page 7 of 12 GHS Globally Harmonized System of Classification and Labeling of Chemicals HR45N Hardness Rockwell 45N HRC Hardness Rockwell C HV10/HV30 Hardness Vickers ISO International Organizat

    48、ion for Standardization Max. Maximum Min. Minimum Mn Manganese MSDS Material Safety Data Sheet Ni Nickel POPP Pre-opened, Pre-positioned PPAP Production Part Approval Process S Sulfur SDS Safety Data Sheet Si Silicon V Vanadium 8 Coding System This standard shall be referenced in other documents, dr

    49、awings, etc., as follows: Material per GMW15184 Type x Where x=A, B, C, D and E as described in 1.3. 9 Release and Revisions This standard was originated in February 2006. It was first approved by the Global Fastening Team in October 2008. It was first published in January 2009. Issue Publication Date Description (Organization) 1 JAN 2009 Initial publicati


    注意事项

    本文(GMW GMW15184-2013 Spring Hose Clamp Issue 3 English.pdf)为本站会员(eastlab115)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开