欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW14728-2012 Determination of the Resistance of Automotive Components to Sulfur Dioxide in a High Humidity Environment Issue 2 English Do Not Use on New Programs Replaced by A.pdf

    • 资源ID:757553       资源大小:43.59KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW14728-2012 Determination of the Resistance of Automotive Components to Sulfur Dioxide in a High Humidity Environment Issue 2 English Do Not Use on New Programs Replaced by A.pdf

    1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure SUPERCEDED GMW14728 Determination of the Resistance of Automotive Components to Sulfur Dioxide in a High Humidity Environment Do Not Use on New Programs; Replaced by ASTM G87 or DIN EN ISO 6988 Copyright 2012 General Motors Company All Rights Reserved

    2、December 2012 Originating Department: North American Engineering Standards Page 1 of 3 1 Scope Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose.

    3、 The purpose of this standard is to determine the resistance of metals, metallic and other protective coatings, normally applied to automotive components to sulphur dioxide in an environment of high humidity. The test is accelerated and carried out using sulphur dioxide injected into air saturated w

    4、ith water vapour at specified temperatures. 1.2 Foreword. Not applicable. 1.3 Applicability. This test is applicable to components that are exposed to the industrial environments. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/

    5、Specifications. ISO 3231 2.2 GM Standards/Specifications. None 3 Resources 3.1 Facilities. Not applicable. 3.2 Equipment. The test apparatus shall consist of the chamber design as defined in IS0 3231 3.3 Test Vehicle/Test Piece. Where possible, the test shall be conducted on complete components. The

    6、 test can also be conducted on specially prepared test panels of a minimum area 250 cm2. 3.4 Test Time. Exposure time and test procedure must be specified by reference document or test requestor. Calendar time: 1 to 6 days Test hours: 24 to 144 hours Coordination hours: to 1 hour 3.5 Test Required I

    7、nformation. Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDAR

    8、DS GMW14728 Copyright 2012 General Motors Company All Rights Reserved December 2012 Page 2 of 3 4.1.1 Test Sample Preparation. Where the size and/or shape of the component prohibit testing of a complete component, test pieces shall be cut from the component. Such test pieces shall have the largest p

    9、ossible size and shall be cut such that the edges are not heavily mechanically deformed nor subjected to excessive temperatures. All cut edges shall be protected in a suitable manner (e.g., with adhesive tapes, protective paints etc.) during test. Any selective portion of a test piece not requiring

    10、testing shall be suitably protected with a material which does not affect or is affected by the test medium. For initial sample approval and arbitration purposes, at least three test pieces shall be tested. For routine quality control, at least one test piece shall be tested. Metallic and metal coat

    11、ed test pieces shall be degreased and cleaned using a non-chlorinated solvent (e.g., Xylene of Petroleum Spirit). The cleaning shall be carried out immediately prior to testing. Anodized aluminium test pieces shall be cleaned with acid free dlchloromethane prior to testing. Test pieces with protecti

    12、ve coatings other than those defined above shall not be cleaned prior to testing. 4.1.2 Test Duration Determination. The test periods for this test are defined below: Code: Test Period (hours/cycles) A: Specifically defined B: 24 h or 1 cycle C: 48 h or 2 cycles D: 72 h or 3 cycles E: 96 h or 4 cycl

    13、es F: 120 h or 5 cycles G: 144 h or 6 cycles 4.1.3 Test Solution Determination. The material to be tested shall determine which of the three sulfur dioxide volumes listed below: Code: Volume of Sulfur Dioxide 2.0 L 1.0 L 0.2 L Note 1: Volume of Sulfur Dioxide is per 300 L of test chamber capacity. 4

    14、.2 Conditions. 4.2.1 Environmental Conditions. Not applicable. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. The test apparatus shall

    15、 be prepared for use according ISO 3231 The test cabinet shall be sealed, injected with sulphur dioxide (as specified based on concentration code) and the cabinet temperature shall be maintained at 40 C 3 C allowing 1.5 h of ramp time for a total of 8 h (including ramp time). 4.3.1 The test cabinet

    16、is then vented and temperature maintained at 23 C 5 C allowing 1.5 h of ramp time for a total of 16 h (including ramp time). One (1) cycle consists of 24 h. At the completion of each cycle, the test pieces shall be removed for interim examination. Furthermore, the reservoir shall be emptied, cleaned

    17、 if necessary and then refilled with the specified volume of test solution and test pieces put back into the test cabinet. The cycle shall be repeated for the designated test duration. At the completing the specified test duration, the test pieces shall be removed from the cabinet and, unless otherw

    18、ise stated, washed with distilled/deionized water and allowed to dry at 23 C 5 C for evaluation. 5 Data 5.1 Calculations. Not applicable. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license fr

    19、om IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14728 Copyright 2012 General Motors Company All Rights Reserved December 2012 Page 3 of 3 5.2 Interpretation of Results. 5.2.1 Evaluation. Visual evaluation of the test pieces or components shall be carried out immediately after the specified test per

    20、iod and appropriate grading allocated according to the following criteria. Grade 1: No change of surface. Grade 2: Change of surface appearance allowed but no corrosion of the base material. Grade 3: Specially defined. 5.2.2 Acceptance Criteria. Acceptance criteria shall be specified on the engineer

    21、ing drawing or in the material specification. 5.3 Test Documentation. The test documentation shall contain at least the following information: 5.3.1 All details necessary to identify the coating tested (type of coating, thickness, etc.) 5.3.2 A reference to this standard. 5.3.3 Conditions and durati

    22、on of the test, including the volume measured at atmospheric pressure of sulfur dioxide to be used (0.2 L, 1.0 L, and 2.0 L). 5.3.4 Results of the evaluation. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety p

    23、roblems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not appl

    24、icable. 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW14728 9 Release and Revisions This standard was originated in October 2005. It was first approved by the Global Corrosion Harmonization Team in December 2006. It was first published i

    25、n August 2007. Issue Publication Date Description (Organization) 1 AUG 2007 Initial publication. 2 DEC 2012 Superceded by ASTM G87 or DIN EN ISO 6988. (Corrosion Global Subsystem Leadership Team) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(GMW GMW14728-2012 Determination of the Resistance of Automotive Components to Sulfur Dioxide in a High Humidity Environment Issue 2 English Do Not Use on New Programs Replaced by A.pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开