欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW14439-2012 Steering Wheel Bending (Push Pull) Fatigue Test Issue 2 English.pdf

    • 资源ID:757490       资源大小:38.71KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW14439-2012 Steering Wheel Bending (Push Pull) Fatigue Test Issue 2 English.pdf

    1、WORLDWIDEENGINEERINGSTANDARDSTest Procedure GMW14439Steering Wheel Bending (Push/Pull) Fatigue Test Copyright 2012 General Motors Company All Rights ReservedOctober 2012 Originating Department: North American Engineering Standards Page 1 of 31 ScopeNote: Nothing in this standard supercedes applicabl

    2、e laws and regulations.Note: In the event of conflict between the English and domestic language, the English language shall takeprecedence.1.1 Purpose. The steering wheel is exposed to bending load in driving operation. A particularly high load isapplied by the driver when repositioning himself in t

    3、he seat. The purpose of this test is to determine the effectof this load applied on the steering wheel.1.2 Foreword. Not applicable.1.3 Applicability. Steering wheels of the entire vehicle range.2 ReferencesNote: Only the latest approved standards are applicable unless otherwise specified.2.1 Extern

    4、al Standards/Specifications.None2.2 GM Standards/Specifications.GMW14095 GMW140962.3 Additional References.Steering Wheel Drawing3 Resources3.1 Facilities. Not applicable.3.2 Equipment.3.2.1 Clamping fixture with steering shaft (see Figure 1).Copyright General Motors Company Provided by IHS under li

    5、cense with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14439 Copyright 2012 General Motors Company All Rights ReservedOctober 2012 Page 2 of 3F12Figure 1: Test SetupLegend for Figure 1:1 = Actuation Cy

    6、linder2 = Steering Wheel AssemblyF = Force3.2.2 Pneumatic or hydraulic cylinder with manual or automatic force control and linear deflectionmeasurement.3.3 Test Vehicle/Test Piece. Test the steering wheel with trim parts and horn control assembly.3.4 Test Time. Not applicable.3.5 Test Required Infor

    7、mation. Not applicable.3.6 Personnel/Skills. Not applicable.4 Procedure4.1 Preparation.4.1.1 The steering wheel assembly, including driver airbag/horn pad, and steering shaft shall be installed onthe clamping fixture. The fastener shall be tightened with the minimum specified torque.4.1.2 The cylind

    8、er shall be installed to apply a force parallel to the steering shaft axis.4.2 Conditions.4.2.1 Environmental Conditions. The test shall be performed at +23 5 C.4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Suchrequirements shall be specified o

    9、n component drawings, test certificates, reports, etc.4.2.2.1 The test frequency shall be 0.66 Hz. A sine wave shall be targeted.4.3 Instructions.4.3.1 The cylinder shall be adjusted to apply a force of 400 N.4.3.2 After completion of the specified cycles or a bending travel of 25 mm at the force-ap

    10、plication point,remove steering wheel foam and the steering wheel shall be checked for deformations or cracks.Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGI

    11、NEERING STANDARDS GMW14439 Copyright 2012 General Motors Company All Rights ReservedOctober 2012 Page 3 of 35 Data5.1 Calculations. Not applicable.5.2 Interpretation of Results.5.2.1 For specified sample sizes, cycles and permissible scattering range see GMW14095 and GMW14096 orthe Steering Wheel Dr

    12、awing.If not otherwise stated in the above documents:x N90% 1000 SSP (Load/Vibration Cycles (Schwingspiel) (SSP)x N90% : N10% 1:2x The maximum number of test cycles conducted, can be limited to two times the N90% value.5.2.2 Cracks and defects of the metal structure are permissible when the specifie

    13、d number of cycles isexceeded (N90% value). The permanent deformation shall be 2 mm.5.3 Test Documentation. With reference to this test method, the results shall be added to a test report.6 SafetyThis standard may involve hazardous materials, operations, and equipment. This standard does not propose

    14、 toaddress all the safety problems associated with its use. It is the responsibility of the user of this standard toestablish appropriate safety and health practices and determine the applicability of regulatory limitations priorto use.7 Notes7.1 Glossary.N10%: Number of load cycles to failure which

    15、 is exceeded by 10% of all test samplesN90%: Number of load cycles to failure which is exceeded by 90% of all test samplesForce-Application Point: The point where the maximum load is applied to the steering wheel rim. In generalthe point on the rim with the maximum distance to the steering wheel spo

    16、kes.7.2 Acronyms, Abbreviations, and Symbols.SSP Load/Vibration Cycles (Schwingspiel)8 Coding SystemThis standard shall be referenced in other documents, drawings, etc., as follows:Test to GMW144399 Release and RevisionsThis standard was originated in September 2005. It was first approved by Interio

    17、rs in March 2006. It was firstpublished in April 2007.Issue Publication Date Description (Organization)1 APR 2007 Initial publication.2 OCT 2012 5 Year Refresh. Added Driver airbag/horn pad to steering wheelassembly. (Interiors)Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(GMW GMW14439-2012 Steering Wheel Bending (Push Pull) Fatigue Test Issue 2 English.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开