欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMW GMW14418-2013 Steering Wheel Torsional Test Issue 2 English.pdf

    • 资源ID:757489       资源大小:472.25KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMW GMW14418-2013 Steering Wheel Torsional Test Issue 2 English.pdf

    1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW14418 Steering Wheel Torsional Test Copyright 2013 General Motors Company All Rights Reserved January 2013 Page 1 of 6 1 Scope Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the Engl

    2、ish and domestic language, the English language shall take precedence. 1.1 Purpose. In driving operation and in particular during parking maneuvers torsional loads are applied to the steering wheel. The purpose of this test is to determine the effect of such loads on the service life of the steering

    3、 wheel. A torque of 70 Nm maximum may be applied to the steering wheel rim when the driver is seated in normal seat position. This value shall be used for the test. 1.2 Foreword. Not applicable. 1.3 Applicability. Steering wheels of the entire vehicle range. 2 References Note: Only the latest approv

    4、ed standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. None 2.3 Additional References. None 3 Resources 3.1 Facilities. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a v

    5、alid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.2 Equipment. 3.2.1 Clamping fixture to hold steering wheel

    6、 rim. 3.2.2 Steering column shaft with torsion arm (See Figure 1). 3.2.3 Pneumatic or hydraulic actuator with manual or automatic force control. Optional: Direct connection of column shaft to hydraulic rotary actuator capable of 70 Nm torque (See Figure 2). 3.3 Test Vehicle/Test Piece. Require three

    7、 (3) steering wheel armatures. 3.4 Test Time. Not applicable. Calendar time: days Test hours: hours Coordination hours: hours 3.5 Test Required Information. Not applicable. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or netw

    8、orking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14418 Copyright 2013 General Motors Company All Rights Reserved January 2013 Page 2 of 6 3.6 Personnel/Skills. Not applicable. 4 Procedure 4.1 Preparation. 4.1.1 The steering wheel shall be mounted on the steering co

    9、lumn shaft. The nut/bolt shall be tightened with the minimum torque. Wait for fastener adhesive patch to cure before proceeding with torsional test as specified by adhesive supplier. Note: If not specified wait 72 h (See Appendix A). 4.1.1.1 Paint stripe the fastener to the wheel interface (See Figu

    10、re 3). 4.1.2 The steering wheel shall be clamped with the shaft to the fixture at steering wheel rim. 4.1.3 The actuator (hydraulic or pneumatic) shall be connected with the torsion arm of the steering shaft (See Figure 1). Note: Optional rotary actuator attachment (See Figure 2). 4.2 Conditions. 4.

    11、2.1 Environmental Conditions. The test shall be performed at + 23 C 5 C. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.2.2.1 The test frequency shall

    12、 be 1.5 Hz. A sine wave shall be aimed. Note: If using rotary actuator test frequency target of 60 cycles/minute (1 Hz). 4.3 Instructions. 4.3.1 The actuator shall be adjusted to produce a torsional load on the steering wheel of 70 Nm maximum attainable at the steering wheel hub. 4.3.2 After complet

    13、ion of 325 000 cycles, the residual torque of the shaft nut/bolt shall be determined and recorded. 4.3.3 The steering wheel shall be inspected for cracks and defects of the armature assembly. 4.3.4. Record if nut/bolt movement from paint stripe. 5 Data 5.1 Calculations. Not applicable. 5.2 Interpret

    14、ation of Results. 5.2.1 No cracks or defects of the armature assembly are permissible before the specified number of cycles are completed. 5.2.2 Steering wheel fastener shall not rotate from initial scribe mark. 5.2.3 Steering wheel attachment to steering shaft shall be “tight” with no increase in a

    15、xial and radial lash. 5.2.4 Steering wheel fastener break-away torque shall be 5 Nm. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW1441

    16、8 Copyright 2013 General Motors Company All Rights Reserved January 2013 Page 3 of 6 Figure 1: Test Setup Key 1 = Actuation Cylinder 2 = Steering Wheel Assembly (clamped) 3 = Torsion Arm L = Length of Torsion Arm F = Calculation (70 Nm = Force x length of torsional arm L) Figure 2: Hydraulic Rotary

    17、Actuator 2F1L3Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14418 Copyright 2013 General Motors Company All Rights Reserved January 201

    18、3 Page 4 of 6 Figure 3: Paint Stripe Note: Example shows bolt movement. 5.3 Test Documentation. With reference to this test method, the results shall be added to a test report. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to addres

    19、s all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and

    20、 Symbols. DC Direct Current RPM Rotations Per Minute 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: Test to GMW14418 9 Release and Revisions This standard was originated in September 2005. It was first approved by Interiors in March 2006. It was fir

    21、st published in May 2007. Issue Publication Date Description (Organization) 1 MAY 2007 Initial publication. 2 JAN 2013 5 Year Refresh. Added optional equipment with pictures. Added number of cycles. (Interiors - Airbags/Steering Wheels/Safety Belts) Copyright General Motors Company Provided by IHS u

    22、nder license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14418 Copyright 2013 General Motors Company All Rights Reserved January 2013 Page 5 of 6 Appendix A A1 Steering Wheel to Steering Column To

    23、rque Analysis A1.1 Use Direct Current (DC) electric or similar calibrated torque controlled power tooling set to 40 Nm final torque target (or as specified) to assemble bolt. A1.2 Tooling RPM is required for analysis: 350 rpm. A1.3 Tool settings: 350 rpm to 15 Nm, downshift to 150 to 250 rpm for rem

    24、ainder of rundown to final torque. A1.4 Perform static torque audit within 3 to 5 minutes of initial assembly using calibrated torque wrench. (See Figure A1). Figure A1: Static Torque Measurement Instructions A1.5 Provide torque versus angle signature (See Figure A2) of the rundown from zero degrees

    25、 angle point to final torque. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14418 Copyright 2013 General Motors Company All Rights Rese

    26、rved January 2013 Page 6 of 6 Figure A2: Torque/Angle Signature Example Note: Torque/Angle Signature Illustration to 30 Nm Target. Three (3) samples Prevailing Torque 5 Nm. Joint seat at 10 Nm. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(GMW GMW14418-2013 Steering Wheel Torsional Test Issue 2 English.pdf)为本站会员(outsidejudge265)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开