欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMKOREA EDS-T-7146-2006 METHOD OF DEFECT TEST FOR BOLT AND NUT (VERSION 2).pdf

    • 资源ID:757243       资源大小:22.76KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMKOREA EDS-T-7146-2006 METHOD OF DEFECT TEST FOR BOLT AND NUT (VERSION 2).pdf

    1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards METHOD OF DEFECT TEST FOR BOLT AND NUT EDS-T-7146 ISSUED DATE: 1994. 04. 01 REVISED DATE: 2006. 06. 19 VERSION: 2 EDS-T-7146METHOD OF DEFECT TEST FOR BOLT AND NUT PAGE: 1/3 ISSUED DATE: 1994. 04. 01 REVISED DATE: 2006

    2、. 06. 19 VERSION: 2 GM DAEWOO Auto & Technology 1. PURPOSE This standard aims at helping test personnel perform the test in an appropriate method by describing the method to examine the defects which may occur on the surface and inside during the manufacture and processing of hardwareNote 1). Note 1

    3、) The hardware refers to bolts, nuts, pins, washers, rivets, etc. But it refers to only bolts and nuts in this standard. 2. SCOPE This standard specifies the method to examine the occurrence of surface defects of hardware used for automobiles. 3. DEFINITIONS 3.1. Surface defects: Surface defects are

    4、 the surface discontinuities on parts, caused by cracks, seams, folds, and laps. etc. 3.2. Cracks: A crack is a crystalline fracture passing through or across the grain boundaries without inclusion of foreign elements. Note 2)The cracks are divided into quench cracks, forging cracks, grinding cracks

    5、, etc. 3.3. Seams: A seam is a continuous line discontinuties running parallel to the product axis, caused by dents, tensile flaws, blowholes, etc. 3.4. Folds: A fold is a doubling over of metal at a intersection of diameter configuration changes which may occur during a faulty forging operation. 3.

    6、5. Lap: A lap is a fold-over of metal parallel to the surface of the threads, caused by an inappropriate thread rolling. 4. TEST 4.1. Testing equipment 4.1.1. Stereoscope: The adjustment of magnification shall be practicable, and the observation by magnifications of 3 to 30 shall be possible. 4.1.2.

    7、 Microscope: The adjustment of magnification shall be practicable, and the observation by magnifications of 50 to 200 shall be possible. 4.2. Test piece 4.2.1. For the test piece, the product as it is(bolt, nut) shall be used. EDS-T-7146METHOD OF DEFECT TEST FOR BOLT AND NUT PAGE: 2/3 ISSUED DATE: 1

    8、994. 04. 01 REVISED DATE: 2006. 06. 19 VERSION: 2 GM DAEWOO Auto & Technology 4.2.2. Impurities on the product surface and grease remaining on the thread surface shall be removed clearly by an ultrasonic cleaner prior to the test. 4.2.3. The number of test pieces shall be 3 or more for initial appro

    9、val, and 1 or more for routine quality control. 5. TEST METHOD The test of surface defect examination shall be divided into 2 methods, macro and micro test method. The surface defect shall be observed by macro method, and then micro method. 5.1. Macro test method This method shall be used mainly for

    10、 observing defects such as bursts, seams, folds. 5.1.1. Observe the product surface visually or using a magnifier or stereoscope. 5.1.2. In case of using the stereoscope, observe from the low to high magnification. 5.1.3. When observing the surface defect, mark its portion using a marking pen or oth

    11、er markable pens. 5.2. Micro test method This method shall be used mainly for observing defect observed by macro method and laps in screw. 5.2.1. Cut off the observed defect part and screw part parallel to the axis using a cut-off machine. Here, pay attention to the cut surface not to discolor due t

    12、o heat. 5.2.2. Grind the cut surface with a grinding machine smoothly. For the sand paper of the grinding machine, use #80. 5.2.3. Mold the ground product using mounting press equipment or epoxy resin. 5.2.4. Grind the molded product using a grinding machine. Here, grind it from grinding of #220 #40

    13、0 #800 to polishing of 1 0.3 0.05 in sequence. 5.2.5. The ground surface shall be mirror-like surface without scratch, etc. 5.2.6. Decide the defect type by observing the observed defect part or threads of screw by the macro method under a microscope. 5.2.7. In this case, observe from the low magnif

    14、ication of 50 to the high magnification. 5.2.8. Observe the general defect under a magnification of 100, and measure the defect size using a ruler with scale of a ocular. 6. EVALUATION Evaluation of the surface defects shall conform to the relevant standard and specifications on the drawing. EDS-T-7

    15、146METHOD OF DEFECT TEST FOR BOLT AND NUT PAGE: 3/3 ISSUED DATE: 1994. 04. 01 REVISED DATE: 2006. 06. 19 VERSION: 2 GM DAEWOO Auto & Technology 7. REFERENCE KS B 0101 Screw threads and fasteners-Vocabulary DIN 267 Part 19 Surface discontinuities on bolt and screw DIN 267 Part 20 Surface discontinuities on nut GM 6102-M Surface discontinuities on bolt and screw GM 6103-M Surface discontinuities on nut


    注意事项

    本文(GMKOREA EDS-T-7146-2006 METHOD OF DEFECT TEST FOR BOLT AND NUT (VERSION 2).pdf)为本站会员(progressking105)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开