欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    GMKOREA EDS-T-4708-2008 TEST METHOD FOR THERMOSTAT ASSEMBLY.pdf

    • 资源ID:757097       资源大小:74.94KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    GMKOREA EDS-T-4708-2008 TEST METHOD FOR THERMOSTAT ASSEMBLY.pdf

    1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards TEST METHOD FOR THERMOSTAT ASSEMBLY Do Not Use on New Programs. Being Replaced by GMW14078 EDS-T-4708 ISSUED DATE: 1990. 11. 03 REVISED DATE: 2008. 10. 27 VERSION: 4 (Superceded) EDS-T-4708TEST METHOD FOR THERMOSTAT A

    2、SSEMBLY PAGE: 1/3 ISSUED DATE: 1990. 11. 03 REVISED DATE: 2008. 10. 27 VERSION: 4 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project (incl. T250 Program). It is Superceded for all future projects and replaced by GMW14078. 1. PURPOSE This standard aims at specifyi

    3、ng requirements and performance and durability test methods and conditions of thermostats for automobiles, thus enhancing test reliability. 2. SCOPE This standard applies to thermostats for automobiles. 3. NUMBER OF THE SAMPLES Unless otherwise specified, 3 samples shall be used at least for approva

    4、l and quality control tests. The numbers for quality control and approval tests can be adjusted through discussion between sample manufacturers (or suppliers), design engineer and test engineer. 4. EQUIPMENT 4.1. Water bath (max. 150) : 2 EA 4.2. Thermometer (0.1) 4.3. Stop watch 4.4. Dial gage (50m

    5、m) 4.5. Leakage test device 4.6. Durability test equipment 5. TEST PROCEDURE 5.1. Performance test Performance test shall be conducted in the following sequence. Before test, repeat full open and close of the thermostat min. 5 cycles with warm and cool water. Used liquid shall be 1:1 mixture of anti

    6、-freezing solution and water. Before each test, the thermostat shall be dipped in water of 235K. 5.1.1. Valve opening temperature test (1) Set the bath temperature to the lower limit of the specified temperature range. (2) Mount the thermostat to the jig and zero the dial gage. EDS-T-4708TEST METHOD

    7、 FOR THERMOSTAT ASSEMBLY PAGE: 2/3 ISSUED DATE: 1990. 11. 03 REVISED DATE: 2008. 10. 27 VERSION: 4 GM DAEWOO Auto & Technology (3) Put the jig into the bath and leave it for a time span of 4 times the thermostat time constant. (4) After checking opening of the valve, gradually raise or lower the bat

    8、h temperature to measure temperature when the valve opens 0.1mm. 5.1.2. Valve full opening stroke test (1) Set the bath temperature to the specified value. (2) Perform clause 5.1.1 (2) and (3) (3) Measure the valve full opening stroke. 5.1.3. Valve opening speed test (1) Prepare two sets of the bath

    9、 and keep them at the specified temperature. 1) Bath 1 : 235K 2) Bath 2 : specified temperature (high temperature) (2) Put the jig with the thermostat into bath 1. (3) Move the jig promptly to bath 2, and with this moment as 0 second, measure the time taken until the valve opens 0.1m. (4) The valve

    10、shall open within 70 seconds. 5.1.4. Leakage test * Test pressure : 100 KPa., test temperature : 235K (1) Set the thermostat to the leakage test device. (2) Open the valve to apply water pressure, and measure leakage. 5.1.5. Responsiveness test (1) Take two arbitrary temperature points of t1 and t2

    11、in the range where the thermostat valve opening characteristic is virtually of a straight line. (See Fig 1) (2) Prepare two baths and keep water temperature to t1 and t2 respectively. (3) Put the thermostat into t1 bath and keep it until the valve lift is sufficiently stabilized. (4) Move the thermo

    12、stat promptly to t2 bath, and with this moment as 0 second, measure and record the time and valve lift simultaneously. This relation is expressed as in Fig 2. The time (T seconds) when valve opening exceeds (L2-L1)0.63 is called the “time constant“ of the thermostat. EDS-T-4708TEST METHOD FOR THERMO

    13、STAT ASSEMBLY PAGE: 3/3 ISSUED DATE: 1990. 11. 03 REVISED DATE: 2008. 10. 27 VERSION: 4 GM DAEWOO Auto & Technology 5.2. Durability test Leave the performance-tested thermostat into warm water of 110 until the valve opens fully, and then leave it into cold water of 60 until the valve closes fully. Conduct 30,000 cycles with 3 minutes as one cycle. For every 10,000 cycles of durability test, conduct performance test.


    注意事项

    本文(GMKOREA EDS-T-4708-2008 TEST METHOD FOR THERMOSTAT ASSEMBLY.pdf)为本站会员(eventdump275)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开