欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSS-M3H128-A2-2008 CARPET BCF NYLON LOW LOOP PILE LATEX BACKCOATED HEAVY LAYER SUBSTRATE BACKING 670g m2 FLOOR MATS TO BE USED WITH FORD WSS-M99P1111-A 《地板垫用670g m2的厚层基底背衬的乳.pdf

    • 资源ID:753293       资源大小:66.98KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSS-M3H128-A2-2008 CARPET BCF NYLON LOW LOOP PILE LATEX BACKCOATED HEAVY LAYER SUBSTRATE BACKING 670g m2 FLOOR MATS TO BE USED WITH FORD WSS-M99P1111-A 《地板垫用670g m2的厚层基底背衬的乳.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions Rev. 2 2008 11 05 N-STATUS Replaced by WSS-M15P44-B L. Sinclair, FNA 2001 10 22 Activated M. Dumitrescu Printed copies are uncontrolled Page 1 of 5 Copyright 2008, Ford Global Technologies, Inc. CARPET, BCF

    2、NYLON, LOW LOOP PILE, LATEX BACKCOATED, WSS-M3H128-A2 HEAVY LAYER SUBSTRATE BACKING, 670g/m2, FLOOR MATS NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a bulked continuous filament (BCF) nylon, low loop pile carpet, tufted into a synthetic primary foundation and

    3、 then coated with a latex back coating which is then laminated to a heavy layer substrate. 2. APPLICATION This specification was released for material used for accessory floor mats applications on 2003 Ford vehicles. 3. REQUIREMENTS In addition to the requirements listed herein, the end-item carpet

    4、assembly (molded or otherwise fabricated) shall meet all requirements of the WSS-M15P44-A performance specification for accessory floor mat applications. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to Quality System Requirements, QS-9000. Material specification

    5、 requirements are to be used for initial qualification of materials. A Control Plan for ongoing production verification is required. This plan must be reviewed and approved by the relevant Ford Materials activity and/or Ford Supplier Technical Assistance (STA) prior to production parts submission. A

    6、ppropriate statistical tools must be used to analyze process/product data and assure consistent processing of the materials. Material specification requirements are to be used for initial qualification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform t

    7、o the Companys Quality System Requirements. ENGINEERING MATERIAL SPECIFICATION WSS-M3H128-A2 Page 2 of 5 Copyright 2008, Ford Global Technologies, Inc. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established for initial approval shall constitute the reference st

    8、andard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material co

    9、nditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods prior

    10、to any subsequent operations, such as reheating or molding. 3.5 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be specified on the engineering drawing. 3.6 COMPOSITION (ASTM D 276) Pile Yarn Nylon 66 Primary Foundation Materi

    11、al * Backcoating Latex* Backing Heavy Layer Substrate* * As specified on the Approved Source List * As required to achieve specified tuft lock and fiber weight loss requirements per WSS-M15P44-A ENGINEERING MATERIAL SPECIFICATION WSS-M3H128-A2 Page 3 of 5 Copyright 2008, Ford Global Technologies, In

    12、c. 3.7 CONSTRUCTION 3.7.1 Pile Yarn (ASTM D 418) (crimped texture, bulked continuous filament, nylon) x 2; B 260 280 tex 3.7.2 Pile Count, min (ASTM D 418) Rows 39.2/100 mm Stitches 55.0/100 mm Rows and stitches per 100 mm shall be based on an average count on a 254 mm length of carpet and shall not

    13、 exceed minus 2/100 mm. 3.7.3 Foundation Materials Primary (Tufting Foundations) * * As specified on the Approved Source List 3.7.4 Backcoating 3.7.4.1 Latex The latex shall form a continuous and uniform coating over the back of the carpet so that all pile fibers are covered. The latex shall be thor

    14、oughly melted and shall maintain its ability to lock in the pile fibers in the end-item, carpet mat assembly. The latex shall thoroughly saturate the base of the pile fiber bundles to ensure adequate tuft lock. Penetration of the latex through to the face shall be controlled to provide the required

    15、resistance to abrasion and fiber loss, but the backcoating shall not be visible on the face of the pile fiber. 3.7.4.2 Heavy Layer Substrate The latex backed carpet shall be securely bonded to a heavy layer substrate which shall be of adequate weight and thickness to allow the formation of uniform n

    16、ibs. 3.7.5 Needle Gauge 2.5 mm ENGINEERING MATERIAL SPECIFICATION WSS-M3H128-A2 Page 4 of 5 Copyright 2008, Ford Global Technologies, Inc. 3.7.6 Pile Height, min 3.9 mm (ASTM D 418) 3.8 WEIGHT, g/m2, minimum (ASTM D 418/FLTM AN 102-02) Pile Yarn 670 Primary Foundation Material * Latex * Heavy Layer

    17、Substrate, min 2200 * As specified on the Approved Source List * As required to meet the tuft pull, fiber weight loss, abrasion requirements on the end item mat carpet per WSS-M15P44-A. 3.9 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute 3.10 ADDITIONAL REQUIREMENTS Additional requirem

    18、ents for material and/or manufactured parts may be specified on the Engineering drawing, Engineering parts specification, performance specification, System Design Specification (SDS) and/or Component Design Specification (CDS). 3.11 SUPPLIERS RESPONSIBILITY All materials supplied to this specificati

    19、on must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supp

    20、lier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specif

    21、ication, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. ENGINEERING MATERIAL SPECIFICATION WSS-M3H128-A2 Page 5 of 5 Cop

    22、yright 2008, Ford Global Technologies, Inc. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials critical to the Companys

    23、business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a com

    24、pleted copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. The original carpet construction approved under this specification employed a primary backing as follows: 5.1 COMPOSITION (ASTM D 276) Primary Foundation Material 100 % Polyester


    注意事项

    本文(FORD WSS-M3H128-A2-2008 CARPET BCF NYLON LOW LOOP PILE LATEX BACKCOATED HEAVY LAYER SUBSTRATE BACKING 670g m2 FLOOR MATS TO BE USED WITH FORD WSS-M99P1111-A 《地板垫用670g m2的厚层基底背衬的乳.pdf)为本站会员(刘芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开