欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSS-M2C920-A-2010 OIL ENGINE INITIAL AND SERVICE FILL ACEA A5 B5 SAE 0W-30 TO BE USED WITH FORD WSS-M99P1111-A 《电泳原漆和耐用填充发动机油ACEA A5 B5 SAE 0W-30 与福特WSS-M99P1111-A 一起使用》.pdf

    • 资源ID:752733       资源大小:86.51KB        全文页数:10页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSS-M2C920-A-2010 OIL ENGINE INITIAL AND SERVICE FILL ACEA A5 B5 SAE 0W-30 TO BE USED WITH FORD WSS-M99P1111-A 《电泳原漆和耐用填充发动机油ACEA A5 B5 SAE 0W-30 与福特WSS-M99P1111-A 一起使用》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 08 10 N-STATUS No replacement named D. DiGregorio, NA 2005 03 17 Activated R. Johansson (rjohan29), Carl Stow, Uwe Zimmer Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 10 OIL, ENGINE, INITIAL AND

    2、SERVICE FILL, ACEA A5/B5 SAE 0W-30 WSS-M2C920-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE These material specifications define the minimum acceptable performance requirements and physical/chemical properties of engine oils to be used by Ford Motor Company in its worldwide engine/vehicle manufacturing o

    3、perations. 2. APPLICATION This specification is released in Europe for initial fill engine oils used for lubrication of spark ignition engines using gasoline and for compression ignition engines using diesel fuels. The specification is also used to define engine oils for servicing Ford engines where

    4、 applicable. Sections titled QUALITY SYSTEM REQUIREMENTS, SUPPLIERS RESPONSIBILITY, and APPROVAL OF MATERIALS (referenced in WSS-M99P1111-A) apply only to engine oils supplied directly to Ford Motor Company and its affiliates. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Materi

    5、al suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 PERFORMANCE Shall meet all the requirements of “ACEA European Oil Sequences 2002, A5 and B5“ and the API SL Sequence VI-B fuel economy test plus additional VCC requiremen

    6、ts. Where applicable, the required engine tests shall be conducted in accordance with the most recently approved procedures as described in ASTM Special Technical Publications 315 and the applicable ASTM Standards, Research Reports and Information Letters and with the ACEA sequences. All tests under

    7、 surveillance by ASTM must be conducted using test equipment monitored by and calibrated to the requirements of the ASTM Test Monitoring Center. All engine performance testing used to support a claim of compliance with the ACEA sequences must be generated according to the EELQMS. Suppliers must demo

    8、nstrate commitment to comply with the ATIEL Code of Practice. 3.3 VISCOSITY GRADE Shall meet all the requirements of the applicable SAE viscosity grade as defined in SAE Standard J300 (latest revision), “Engine Oil Viscosity Classification“. 3.3.1 Low Temperature Pumping Viscosity, 60,000 mPa.s at -

    9、40 C, max (ASTM D 4684, MRV TP-1) ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 10 3.4 PHYSICAL/CHEMICAL PROPERTIES 3.4.1 Copper Corrosion, max 1b (ASTM D 130 or ISO 2160, 3 h at 100 C) (Dark Orange) 3.4.2 Foami

    10、ng (High Temperature, 50/0 ml, ASTM D 6082), max 3.4.3 Seal Compatibility Shall be compatible with all current production component materials. 3.4.4 Physical Appearance and Odor Shall be clear and bright with no objectionable odor. 3.4.5 Contaminants Shall be free of carcinogens, toxins, metals not

    11、removed in refining or from previous use. 3.5 “READ ACROSS“ GUIDELINES All performance tests must be conducted on the final oil formulations for consideration for initial fill. Exceptions may be permitted with supporting supplementary data on similar formulations to allow for approval in the absence

    12、 of complete testing. 3.6 QUALIFICATION PROCEDURE 3.6.1 Documentation Supplier must furnish to the affected Materials Engineering activity a completed and certified copy of the attached Supplement A, test reports demonstrating full compliance with all the requirements of this specification and a cop

    13、y of the final ERC summaries if available. The need ATIEL registration of tests will be determined by the affected Materials Engineering activity. The copy of the ERC summaries should be sent directly from ERC to the Materials Engineering activity unless specifically instructed by that activity. The

    14、 test reports must include results on both the candidate oil and the appropriate reference oils. The standard photographs of the test components are considered an essential part of the required test documentation. The oil sample code used for identification in each test document must be consistent.

    15、Any deviation in sample code uniformity must be explained and shown on the cover of each test report. All tests must be certified by a qualified and authorized representative of the test facility. The supplier shall identify all the formulation changes and modifications that occurred in the test pro

    16、gram that coincide with the tests listed in the ERC Summaries. Individual formulations should be listed in Supplement A, and for registered tests, identified by the line item number and the formulation code. ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 201

    17、0, Ford Global Technologies, LLC Page 3 of 10 3.6.2 Verification The affected Materials Engineering activity reserves the right to conduct verification testing. If the test results do not support the originally submitted data, the supplier must re-test the product in coordination with the affected M

    18、aterials Engineering activity. This re-test must be conducted and certified by a mutually agreed upon test facility. 3.6.3 Chemical and Physical Properties Supplier shall furnish appropriate chemical and physical properties as required on Supplement A along with the manufacturing limits that apply t

    19、o the material upon which approval is requested. 3.6.4 Performance Requirements Conformance to the engine test requirements listed in Supplement A will be determined by using Multiple Test Acceptance Criteria (MTAC), where applicable. All data and reports from the tests used for MTAC must be provide

    20、d by the supplier. On Supplement A identify the engine tests that have been used to determine the MTAC results by the corresponding line item number on the ACC Summary. The affected Materials Engineering activity reserves the right to use all tests when averaging in place of MTAC. For final product

    21、approval of the material for initial fill further in-house testing is required in addition to the requirement outlined herein (Design Validation Testing). 3.6.5 Quality Control Upon engineering approval, supplier and affected Materials Engineering activity shall establish mutually agreed upon qualit

    22、y control limits, to be listed on Supplement B, and will be used for ongoing product verifications at mutually agreed upon frequencies. The infrared absorption spectra of the approved material shall constitute the reference standard and shall be kept on file. All samples shall produce infrared spect

    23、ra that correspond to the reference standard when tested under the same conditions as those specified on the master spectra. 3.9 FLEET TESTING Materials which, in the opinion of the affected Materials Engineering activity, constitute a significant departure from conventional formulations, whether in

    24、 base stocks, refining processes or additive packages, must be fleet tested, in addition to the requirements outlined herein. These tests must include the type(s) of service judged to be affected by the difference in formulation technology. The affected Materials Engineering activity should be consu

    25、lted prior to testing. ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 4 of 10 (Supplement A, p. 1 of 6) Oil Company_Date_ Product Name_Viscosity Grade_ Product Code_ Blend Plant Location(s)_ Base Stocks Manufacturing

    26、Limits Nominal Base Oil Viscosity, mm2/s Cloud Point, C/ Type Volume % 100 C 40 C Sulfur, % Pour Point, C A _ _ _ _ _ B _ _ _ _ _ C _ _ _ _ _ D _ _ _ _ _ Refinery Name and Location Process Type Crude Source A _ _ _ B _ _ _ C _ _ _ D _ _ _ Note: Viscosity Sulfur Cloud Point Pour Point (ASTM D 445) (A

    27、STM D 129) (ASTM D 2500) (ASTM D 97) (ASTM D 1552) (ASTM D 2622) Additives Carrier Oil Additive In Type/ Manufacturer In Additive Finished Oil Function Name Code Description Volume % Volume % E _ _ _ _ _ _ F _ _ _ _ _ _ G _ _ _ _ _ _ H _ _ _ _ _ _ I _ _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL

    28、 SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 5 of 10 (Supplement A, p. 2 of 6) Oil Company_Date_ Product Name_Viscosity Grade_ Product Code_ (MTAC) Performance Requirements Test #/Date Specification Test Results Engine Rusting ASTM Bal

    29、l Rust Test Ball Rust Test _ Average Gray Value 100 min _ Oxidative Stability Sequence IIIF _ Viscosity Increase at 40 C, 60 h - _NR_ Viscosity Increase at 40 C, 80 h 275 max _ Weighted Piston Deposits (merits) 4.0 min _ Average Piston Skirt Varnish (merits) 9.0 min _ Stuck Piston Rings none _ Cam +

    30、 Lifter Wear, average, m 20 max _ Oil Consumption (liters) 5.2 max _ Low Temperature Sludge and Valvetrain Wear ASTM Sequence VG plus ASTM Sequence IVA Sequence VG (ASTM D 6593) _ Average Engine Sludge 7.8 min _ Rocker Cover Sludge 8.0 min _ Average Piston Skirt Varnish 7.5 min _ Average Engine Varn

    31、ish 8.9 min _ Oil Ring Clogging Report _ Oil Screen Clogging 20.0% max _ Stuck Compression Rings (Hot) none _ Sequence IVA _ Cam Wear (7 position average), m 120 max _ Bearing Corrosion ASTM Sequence VIII Sequence VIII _ Bearing Weight Loss, mg 26.4 max _ Fuel Efficiency ASTM Sequence VIB Sequence V

    32、IB _ FEI-1 1.7% min _ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 6 of 10 (Supplement A, p. 3 of 6) Oil Company_Date_ Product Name_Viscosity Grade_ Product Code_ (MTAC) Performance Requirements Test #/Date Specific

    33、ation Test Results High Temperature Deposits, Ring Sticking and Oil Thickening TU5JP L4 (CEC-L-88-T-02) 72 hour _ Ring Sticking (each part) 9.0 min _ Piston Varnish (6 element) RL216 min _ Absolute Viscosity Increase, 40 C 0.8 x RL216 viscosity Change from min to max value during test increase, max

    34、_ Low Temperature Sludge Sequence VG (ASTM D 6593-00) _ Average Engine Sludge 7.8 min _ Rocker Cover Sludge 8.0 min _ Piston Skirt Varnish 7.5 min _ Average Engine Varnish 8.9 min _ Oil Ring Clogging Report _ Oil Screen Clogging 20.0% max _ Stuck Compression Rings (Hot) none _ Valve Train Scuffing W

    35、ear TU3M (CEC-L-38-A-94) _ Cam Wear Average, m 10 max _ Maximum, m 15 max _ Pad Merit (average of 8 pads) 7.5 min _ Black Sludge M111 (CEC-L-53-T-95) _ Average Engine Sludge RL140 min _ Fuel Efficiency M111 (CEC L-54-T-96) _ 2.5% min _ DI Diesel Piston Cleanliness and Ring Sticking VW DI (CEC L-78-T

    36、-99) _ Piston Cleanliness RL206 min _ Ring Sticking (rings 1 Report values - “NIL“ or Trace“ are not permissible S _ _ _ _ _ P _ _ _ _ _ Zn _ _ _ _ _ Ba _ _ _ _ _ Ca _ _ _ _ _ Mg _ _ _ _ _ Na _ _ _ _ _ N _ _ _ _ _ B _ _ _ _ _ Cu _ _ _ _ _ Cl _ _ _ _ _ Sulfated Ash _ _ _ _ _ V. Tests Conducted _ _ _

    37、_ _ Comments: _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 9 of 10 (Supplement A, p. 6 of 6) Oil Company_Date_ Product Name_ Product Code_ Specification Test Mfg. Physical/Chemical Proper

    38、ties Requirements Results Limits Viscosity at 150 C (ASTM D 445), mm2/s report _ _ Viscosity at 100 C (ASTM D 445), mm2/s 9.3-.001 %) report _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATIONWSS-M2C920-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 10 of 10 (Supplement B, p. 1 of 1) Oil Company_ Date_ Product Name_ Blend Location _ Product C


    注意事项

    本文(FORD WSS-M2C920-A-2010 OIL ENGINE INITIAL AND SERVICE FILL ACEA A5 B5 SAE 0W-30 TO BE USED WITH FORD WSS-M99P1111-A 《电泳原漆和耐用填充发动机油ACEA A5 B5 SAE 0W-30 与福特WSS-M99P1111-A 一起使用》.pdf)为本站会员(花仙子)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开