欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSS-M1J216-A-2012 PAINT AIR OR FORCED DRYING FUEL TANKS TO BE USED WITH FORD WSS-M99P1111-A .pdf

    • 资源ID:752457       资源大小:26.96KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSS-M1J216-A-2012 PAINT AIR OR FORCED DRYING FUEL TANKS TO BE USED WITH FORD WSS-M99P1111-A .pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev 03 2012 06 25 N Status No usage or replacement N. Benipal, NA 2007 12 17 Revised Updated Format, No Technical Change 1997 10 28 Activated D. Green Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of 3 PA

    2、INT, AIR OR FORCED DRYING, FUEL TANKS WSS-M1J216-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is an air drying or force drying paint. It is essentially for providing fuel tanks with improved cosmetic appearance, and enhancing the resistance performance of the s

    3、ubstrate material. 2. APPLICATION The material is generally used for coating lead plated steel (Terne Plate) fuel tank surfaces. The material must be suitable for pneumatic, airless and electrostatic application. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers a

    4、nd part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 COMPOSITION 3.4.1 Vehicle The resin shall be based on a suitable synthetic system to obtain the desired application and resistance properties. 3.4.2 Pigment The pigment shall be balanc

    5、ed and blended to give the desired color, normally black, unless specified on the component drawing. 3.4.3 Solvent Solvents should be balanced in order to provide suitable storage and application viscositys, while at the same time avoiding flocculation and maintaining correct solvent emission levels

    6、. 3.4.4 Specific Composition When it is necessary to obtain specific data regarding material formulation, it is understood that the supplier will furnish such data on request. It may be necessary to supply such information in order to clarify the toxicological status of the material with respect to

    7、National or Local Protection Agency constrictions. ENGINEERING MATERIAL SPECIFICATIONWSS-M1J216-A Copyright 2012, Ford Global Technologies, LLC Page 2 of 3 3.5 PHYSICAL PROPERTIES 3.5.1 Non-Volatile Initial Sample +/- 1.00% (FLTM BI 102-01) 3.5.2 Density Initial Sample +/- 0.05 g/mL (ASTM D 1475) 3.

    8、5.3 Viscosity As Received Initial Sample +/- 5 s FC-4/25 C (FLTM BI 111-01) 3.5.4 Viscosity As Used As Recommended by Supplier (FLTM BI 111-01) 3.5.5 Shelf Stability No excessive change in viscosity (Storage Stability) and no noticeable hard settling (FLTM BI 102-03) 3.5.6 Solvent Emissions The vola

    9、tile portion of this material shall meet the applicable requirements of the local air pollution control for the assembly plants in which the coating is used. 3.6 PREPARATION OF TEST PANELS (FLTM BI 103-02) 3.6.1 Substrate Ford Engineering Approved Standard Terne Plate, as used by the relevant Compon

    10、ent Supplier. 3.6.2 Cleaning Remove all surface oil, grease, and dust with a suitable solvent as described in FLTM BI 103-03, Method F. 3.7 APPEARANCE 3.7.1 General Appearance Coating should provide sufficient coverage to obscure any minor surface defects effecting the overall appearance. 3.7.2 Colo

    11、r (FLTM BI 109-01) Black unless stated otherwise on Engineering Drawing. Color should match Approved Master Appearance color panel. 3.7.3 Gloss (FLTM BI 110-01, 60 glossmeter) Gloss shall match the Master Appearance color panel. ENGINEERING MATERIAL SPECIFICATIONWSS-M1J216-A Copyright 2012, Ford Glo

    12、bal Technologies, LLC Page 3 of 3 3.8 FILM PROPERTIES 3.8.1 Film Thickness 25 - 35 micrometers (FLTM BI 117-01) Coating must be sufficient to meet all performance requirements of this specification. 3.8.2 Dry Hiding Power, max 20 micrometers (FLTM BI 158-01) 3.8.3 Drying If allowed to air dry, shoul

    13、d be sufficiently dry at normal room temperature, 25 +/- 1 C. 45 - 65% RH, within 15 minutes of application. Forced dry conditions should be those recommended by the supplier. 3.9 RESISTANCE PROPERTIES 3.9.1 Adhesion Grade 0 (FLTM BI 106-01, Method B) No chipping 3.9.2 Water Immersion 96 h (FLTM BI

    14、104-01) No blistering, softening, or adhesion loss 3.9.3 Salt Spray Exposure 96 h (FLTM BI 103-01) No rust spots, blistering, chipping, peeling, or adhesion loss more than 3 mm from scratches, scar marks, sharp edges or scribe lines. 3.9.4 Fuel Resistance (FLTM BI 152-01) Petrol Resistance Current initial fill gasoline, Standards Premium Grade Diesel Resistance Current initial fill Diesel, National Standard Premium Grade Resistance Test should be carried out using the Local or National Fuel which is predominantly used in the area where the Tank is scheduled for general usage.


    注意事项

    本文(FORD WSS-M1J216-A-2012 PAINT AIR OR FORCED DRYING FUEL TANKS TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(boatfragile160)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开