欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSS-M1F21-D1-2017 SPLIT GRAIN LEATHER GENUINE FINISHED STEERING WHEEL SHIFT KNOB AND BOOT TO BE USED WITH FORD WSS-M99P1111-A .pdf

    • 资源ID:751633       资源大小:23.91KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSS-M1F21-D1-2017 SPLIT GRAIN LEATHER GENUINE FINISHED STEERING WHEEL SHIFT KNOB AND BOOT TO BE USED WITH FORD WSS-M99P1111-A .pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 00 2017 07 17 Released A.Wagenhals, FNA Controlled document at www.MATS.com Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 SPLIT GRAIN LEATHER, GENUINE, FINISHED, STEERING WSS-M1F21-D1 WHEEL, SHIFT KNOB AND BOOT 1. SCOPE The ma

    2、terial defined by this specification is tanned split grain from steer or heifer hides. The finish coating shall be a series of pigmented or clear resins to ensure compliance to all requirements in this specification. 2. APPLICATION This specification was released originally for split grain leather f

    3、or hand wrapped steering wheels, shift knobs, and shift/handbrake boots. 2.1 LIMITATIONS - This leather is not to be used for seating, interior trim, or instrument panel applications - Fully perforated leather is not to be used on steering wheels or shift knobs. 3. REQUIREMENTS 3.1 APPROVED SOURCES

    4、This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally thro

    5、ugh a Ford Materials Engineer. 3.2 APPEARANCE The color, grain, gloss and hand shall match the approved Corporate Design master sample. 3.3 SPLIT GRAIN The bottom layer of a leather that has been mechanically split into two layers. This bottom layer serves as the top/appearance surface. 3.4 LEATHER

    6、PERFORMANCE Materials manufactured to this specification shall also meet the requirements contained in WSS-M98P12-C2/latest. Test plans for both construction and color approvals can be found on Table 1 within WSS- M98P12-C2/latest. ENGINEERING MATERIAL SPECIFICATIONWSS-M1F21-D1 Copyright 2017, Ford

    7、Global Technologies, LLC Page 2 of 3 3.5 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning envi

    8、ronment or soon after removal. 3.6 SAMPLE SELECTION LOCATIONS The location of the test samples is described in ISO 2418 or ASTM D2813 for physical testing of leather samples. Refer to WSS-M98P12-C2/latest for samples to be taken from the belly and backbone areas as noted in Table 1 of that specifica

    9、tion. 3.7 FINISH The leather crust must be similar in color (minimum 80% color match) to the surface coating. This is to prevent undyed fibers from showing through after sewing . No correcting or repair of any kind shall be allowed including but not limited to buffing, filling, or stuccoing. Buffing

    10、 is allowed for split leather only. 3.8 THICKNESS 1.1 1.4 mm (ASTM D1813) 3.9 BREAKING STRENGTH 1000 N min (ASTM D2208) 3.10 ELONGATION AT 100 N 4 - 14 % (ISO 3376, Cross and longitudinal directions Specimen size 50 X 100 +/- 2 mm, 50 mm/min test speed, 2 N preload) 3.11 TEAR STRENGTH 100 N min (AST

    11、M D5733, any direction) 3.12 STIFFNESS Report Range (FLTM BN 157-02, measurements shall be taken along either side of the backbone.) Note: Reported range in the construction approval package must be maintained lot to lot throughout production. 3.13 SHRINKAGE 7% max (FLTM BN 105-03, except heat cycle

    12、 at 100+/-2 C, 3 cycles, Report all measurements) 3.14 ADHESION OF SURFACE COATING (ISO 11644, Adhesive Henkel Sicomet 8400 or equivalent Supplier: Henkel, or equivalent Condition bonded test specimens for 1 hour min.) 3.14.1 As received 15 N/10 mm min 3.14.2 After Humidity 12 N/10 mm min (7 days at

    13、 70 +/- 2 C and 95 +/-5% RH) ENGINEERING MATERIAL SPECIFICATIONWSS-M1F21-D1 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questi

    14、ons concerning Engineering Material Specifications. 4.1 TYPICAL STIFFNESS RANGE 75 - 95 mm (FLTM BN 157-02, measurements taken along either side of the backbone.) 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, De

    15、sign or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested

    16、 material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.3 SUPPLIERS ONGOING RESPONSIB

    17、ILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier sha

    18、ll notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications,

    19、all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.4 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies t

    20、o the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS


    注意事项

    本文(FORD WSS-M1F21-D1-2017 SPLIT GRAIN LEATHER GENUINE FINISHED STEERING WHEEL SHIFT KNOB AND BOOT TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(confusegate185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开