欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSK-M97D2-A-2006 PHENOLIC (PF) 40 % GLASS FIBER REINFORCED SHEET TO BE USED WITH FORD WSS-M99P111-A 《40%玻璃纤维增强的酚醛树脂(PF)板 与标准FORD WSSS-M99P111-A一起使用 》.pdf

    • 资源ID:751033       资源大小:93.94KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSK-M97D2-A-2006 PHENOLIC (PF) 40 % GLASS FIBER REINFORCED SHEET TO BE USED WITH FORD WSS-M99P111-A 《40%玻璃纤维增强的酚醛树脂(PF)板 与标准FORD WSSS-M99P111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2006 09 20 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.6, 3.7 & 4 1992 05 01 Released EP00E10176267000 P. Kuntze Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 3 PHENOLIC (PF) 40% GLASS FIBER REINFO

    2、RCED SHEET WSK-M97D2-A 1. SCOPE The material defined by this specification is a high heat resistant composite sheet of 40% chopped strand E glass fibers homogeneously encapsulated in a fully curable phenolic resin. This material is self- extinguishing (SE) without flame retardant additives. It may b

    3、e used for the hand-lay process, direct fiber preform process or modified wet-lay-up molding. 2. APPLICATION This specification was released originally for material used for heat insulation shields. Note: This material absorbs water and should not be used without surface protection. 3. REQUIREMENTS

    4、3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 MOLDED TEST SPECIMEN 3.4.1 Preparation of Test Specimens All test specimens shall be die-cut from strainless mold

    5、ed flat test sheets manufactured from the same material composition and under equivalent process conditions as production parts. The thickness of test specimen shall be 2.5 +/- 0.5 mm. Edges of specimens shall be flat, clean and at right angles to the surface. Before die-cutting of the individual te

    6、st specimen, the molded test sheets shall be annealed according to the following cycle: 30 minutes at 50 - 55 C 4 h at 80 - 85 C 24 h minimum at 23 +/- 2 C 3.4.2 Density (ISO 1183, Method A/ASTM D 792, Method A1) Hand-lay-up Process 1.15 - 1.35 g/cm3 Direct Fiber Preform Process 1.10 - 1.30 g/cm3 3.

    7、4.3 Ash Content 30 - 45% (ISO 3451/1, Method A, except 2 h at 850 +/- 50 C) ENGINEERING MATERIAL SPECIFICATION WSK-M97D2-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 3 3.4.4 Tensile Strength at Break, min 50 MPa (ISO R 527/ASTM D 638M, 150 min x 10 x 2.5

    8、+/- 0.5 mm specimen, 5 mm/min test speed) 3.4.5 Flexural Modulus, min 4.7 GPa (ISO 178/ASTM D 790M, Method I, Procedure A, 80 x 10 x 2.5 +/- 0.5 mm specimen, 1.25 mm/min test speed, 64 mm support span, the radius of the loading nose 5.0 +/- 0.1 mm and of the supports 2.0 +/- 0.2 mm) 3.4.6 Flexural S

    9、trength, min 75 MPa (Test method per para 3.4.5) 3.4.7 Impact Strength, Izod, Unnotched, min (ISO 180/ASTM D 256, no notch on either side, 80 x 10 x 2.5 +/- 0.5 mm specimen, 10 specimens for each test) 3.4.7.1 At 23 +/- 2 C 55 kJ/m2 3.4.7.2 At -40 +/- 2 C 55 kJ/m2 The test specimens must be conditio

    10、ned for minimum of 6 h at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold box, if not possible, test can be conducted outside, but within 5 s. 3.4.8 Heat Aging Performance (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 190 +/- 2 C

    11、. Unaged property values shall be determined at the time of the aged properties determination) 3.4.8.1 Impact Strength, min 20 kJ/m2 (Test Method per para 3.4.7.1, 10 specimens for each test) 3.4.8.2 Flexural Strength, min 10 MPa (Test Method per para 3.4.6, 10 specimens for each test) 3.4.9 Water A

    12、bsorption, max 12% (ISO 62, 96 h/ASTM D 570, 96 h) ENGINEERING MATERIAL SPECIFICATION WSK-M97D2-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 3 3.5 FLAMMABILITY (ISO 3795) Burn Rate, max 100 mm/minute Self-extinguishing (SE) The specimen size required for

    13、material approval is 355 x 100 x 1.8 +/- 0.1 mm with a smooth surface. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 COEFFICIENT OF LINEAR THERMAL EXPANSION 0.7 - 1.3-5/ C (ASTM D 696) 5.2 POST SHRINKAGE (ISO 2577, test specimen 110 x 10 x 4 mm) . After 48 h at 235 C 0.08% 5.3 MAXIMUM TEMPERATURE FOR CONTINUOUS USE 250 C 5.4 RECYCLING CODE SAE or PF-GF40 PF-GF40 OPTIONAL


    注意事项

    本文(FORD WSK-M97D2-A-2006 PHENOLIC (PF) 40 % GLASS FIBER REINFORCED SHEET TO BE USED WITH FORD WSS-M99P111-A 《40%玻璃纤维增强的酚醛树脂(PF)板 与标准FORD WSSS-M99P111-A一起使用 》.pdf)为本站会员(boatfragile160)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开