欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSK-M4G342-A1-2014 SEALER SOLVENT RELEASE NON-SETTING TO BE USED WITH FORD WSS-M99P1111-A .pdf

    • 资源ID:750947       资源大小:60.62KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSK-M4G342-A1-2014 SEALER SOLVENT RELEASE NON-SETTING TO BE USED WITH FORD WSS-M99P1111-A .pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Action Changes1992 02 03 EP00E10176261000 Released W.Scholz Conc. J.SchultWP 3948-a Page 1 of 5 SEALER, SOLVENT RELEASE, NON-SETTING WSK-M4G342-A1/A21. SCOPEThe material defined by this specification is a non-setting sealingco

    2、mpound which is resistant to temperatures between - 40 C and + 250 Cwithin joint faces. The sealer will resist automotive fluids well in excessof normal operating temperatures and gives good clamping force retentioneven where vibration may be encountered.The sealer is supplied, in a range of dilutio

    3、ns, with a solvent which isallowed to evaporate between application and fitting to leave a flexible,coherent film.2. APPLICATIONThis material was originally released for sealing clean mating surfaces onengine or transmission and/or as specified on Engineering drawings.3. REQUIREMENTSThe grade of sea

    4、ler supplied shall be suitable for the method ofapplication as defined by the relevant Component Engineer and ManufacturingDivision.3.1 STATISTICAL PROCESSSuppliers must conform to the requirements of Ford Quality SystemStandard Q-101. A mutually acceptable Control Plan as describedtherein is requir

    5、ed for material/source approval. Appropriatestatistical tools must be used to analyze process/product data sothat variation in the final product is continuously reduced.3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSISFord Motor Company, at its option, may conduct infrared and/orthermal analysi

    6、s of material/parts supplied to this specification.The IR spectra and thermograms established for initial approval shallconstitute the reference standard and shall be kept on file at thedesignated material laboratory. All samples shall produce IR spectraand thermograms that correspond to the referen

    7、ce standard when testedunder the same conditions.3.3 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on material conditioned ina controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested under thesame conditions

    8、unless otherwise specified.NOT TO BE USED FOR NEW DESIGN 2014 N Status No replacment named L. Sinclair, NAENGINEERING MATERIAL SPECIFICATIONWSK-M4G342-A1/A2WP 3948-b Page 2 of 5 3.4 SOLVENT RELEASE SEALER3.4.1 COLOR Blue or as specified on EngineeringDrawingA1 A23.4.2 SOLIDS, %, +/- 3 74 65 (FLTM BV

    9、 150-10)3.4.3 ASH, %, +/- 4 20 20 (FLTM BV 150-10)3.5 SOLVENT FREE SEALERPreparation of Test PanelsThe test panels are to be made of aluminum alloy to BS 1470 S1C/DIN1745 Al 99/ASTM B 209 1100, size 200 x 25 x 0.7 mm approximately.Dress the panels with grade 00 emery paper and d egrease thoroughly b

    10、ywashing with pure acetone. Coat the lower three quarters of one sideof the panel with the sample to give a wet film thickness of 0.2 mmand a llow to dry for 24 h at room temperature in well ventilatedarea.3.5.1 Plasticity after Heat Ageing(16 h at 150 +/- 2 C, 1 h at 23 +/- 2 C)The film shall remai

    11、n p lastic and coherent after bending 180degrees around a 100 mm mandrel.3.5.2 Plasticity at Low Temperatures(-40 +/- 1 C for 1 h)No cracking or chipping after 180 degree bend ar ound a 100 mmmandrel at - 40 C.Note: For the following clauses, 3.5.3 and 3.5. 4, the sampleshall be completely immersed

    12、in the test fluid and shall besupp orted so as to be clear of the bottom of the immersioncontainer. The panels shall be removed and allowed to drainfor 1 h prior to inspection.3.5.3 Resistance to Oil Immersion(140 +/- 2 C for 4 h, ASTM Oil No. 3)No si gnificant evidence of swelling, softening ordegr

    13、adation.ENGINEERING MATERIAL SPECIFICATIONWSK-M4G342-A1/A2WP 3948-b Page 3 of 5 3.5.4 Resistance to Coolant Immersion(90 +/- 2 C for 4 h, 50:50 = water:ESE-M97B44-A*)No si gnificant evidence of swelling, softening ordegradation. Slight whitening allowed.*Or currently released equivalent fluid (see p

    14、ara 5.1).3.5.5 Torque Retention TestTest Method:The test fixture is shown in the appendix. Thoroughlydegrease the mating sur faces with pure acetone and brush thesample as thinly as pos sible over both surfaces and allow toair dry for 10 minutes. Bolt the fixture togethe r and tighteneach nut to a t

    15、orque of 9.0 Nm. Wait 10 minutes and retorqueif necessary to 9.0 Nm.Condition the fixture in an air circulating oven at 250 +/-5 C for 24 h. Remove t he fixture from the oven and allow tocool to room temperature.The minimum torque to tighten each nut further is 7.9 Nm.3.6 STORAGE STABILITY, min 12 m

    16、onths(From date of receipt at Ford Motor Company)When stored in sealed unopened containers out of direct sunlight atambient temperatures between 5 and 32 C.The supplier must label each container to indica te expiration date ofthe material and production usage beyond expiration date is notpermitted.3

    17、.7 QUALITYThe material shall be of uniform quality free from foreign materialand pro perties detrimental to normal production use. It shall notcause excessive soiling of handlers in normal production use.3.8 ADDITIONAL REQUIREMENTSSpecific requirements for material and/or manufa ctured parts shall b

    18、especified on the Engineering drawing, Engineerin g parts specificationand/or performance specifications. All critical areas with respect tothese properties shall be clearly designated on the engineeringdrawing.3.9 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivale

    19、nt inal l characteristics to the material upon which approval wasoriginally granted.ENGINEERING MATERIAL SPECIFICATIONWSK-M4G342-A1/A2WP 3948-b Page 4 of 5 Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved unde

    20、r this specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringac

    21、tivity. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WS S-M99P9999-A1, unlessa

    22、 different suffix (e.g., A2 or A3) is specified on the engineeringdocument for the application.4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by theresponsible Materials Engineeri ng activity. Suppliers desiring approval ofthe ir materials shall first obtai

    23、n an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test reports, signed by aqualified and authorized representative of the test

    24、faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not nominal values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering approval of amateri al will be based on its performance to this specificati

    25、on and on anassessment of suitability for i ntended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.5. GENERAL INFORMATIONThe information below is provided for clarification and assistance inmeeting the requirements of this spe

    26、cification.5.1 For inf ormation on currently approved fluids used in para 3.5.4 ofthis specification contact:Materials Laboratory 13/100 Fluids Materials SectionResearch & Engineering Centre Coolants/GreasesFord Motor company Ltd. Engine EngineeringLaindon, Basildon P.O. Box 2053Essex SS15 6EE, England 21500 Oakwood Blvd.Dearborn, MI 48121 U.S.A.Materials EngineeringProduct Engineering officeFord Motor Co. of Australia Ltd.Princes Highway, NorlaneVictoria 3214, AustraliaENGINEERING MATERIAL SPECIFICATIONWSK-M4G342-A1/A2WP 3948-b Page 5 of 5


    注意事项

    本文(FORD WSK-M4G342-A1-2014 SEALER SOLVENT RELEASE NON-SETTING TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开