欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSK-M11P54-A-2013 PERFORMANCE SEMISTRUCTURAL ADHESIVE POLYURETHANE METAL TO METAL TWO COMPONENT TO BE USED WITH FORD WSS-M99P1111-A .pdf

    • 资源ID:750297       资源大小:31.63KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSK-M11P54-A-2013 PERFORMANCE SEMISTRUCTURAL ADHESIVE POLYURETHANE METAL TO METAL TWO COMPONENT TO BE USED WITH FORD WSS-M99P1111-A .pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Release/Revision1993 06 01 EP00E10258817000 Released B. LangeWP 3948-a Page 1 of 6 PERFORMANCE, SEMISTRUCTURAL ADHESIVE, POLYURETHANE, WSK-M11P54-AMETAL TO METAL, TWO COMPONENT1. SCOPEThis specification defines the

    2、 performance requirements for a solvent free,polyurethane based, semistructural metal-to-metal adhesive.2. APPLICATIONThis specification was released originally to provide life time structuralbondin g for body components such as car cross beam (e-coated) to brackets(chromated steel, dirt and grease

    3、free).3. REQUIREMENTS3.1 STATISTICAL PROCESSSupplie rs must conform to the requirements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for material/source approval. Appropriatestatist ical tools must be used to analyze process/product data s

    4、othat variation in the final product is continuously reduced.3.2 CONDITIONING AND TEST CONDITIONSAll test values indicated herein are based on ma terial conditioned ina control led atmosphere of 23 +/- 2 C and 50 +/- 5 % relativehumidity for not less than 24 h prior to testing and tested under thesa

    5、me conditions unless otherwise specified.3.3 SYSTEMS COMPONENTS3.3.1 SubstratesChrom ated and/or e-coated steel as specified onengineering drawing.Note: If any other s teel, f.e. precoated with Zn,Zn/Ni, Duplex, galvanized, galvanealed, etc. getsrelevant for manufact uring, the adhesive has to betes

    6、te d according to this specification on thesesubstrates.ENGINEERING MATERIAL SPECIFICATIONWSK-M11P54-AWP 3948-b Page 2 of 6 3.3.2 Preparation of SubstrateGrease free, clean unless otherwise specified.3.3.3 Adhesive, Two Component (see 5.1)Suitable to meet the requirements of this specif ication or a

    7、sspecified on engineering drawing.3.3.4 Adhesive Application Temperature 23 +/- 2 C3.3.5 Adhesive Coating ThicknessesX = 1 mm, unless otherwise specified3.3.6 Curing Conditions 7 2 h at 23 +/- 2 C3.4 PERFORMANCE PROPERTIES3.4.1 Green Shear Strength, min 0.3 MPa(FLTM BV 154-03)Test Method:. Prep are

    8、test specimens (body steel quality; see section3.3.1 of specification) according to section B, para 1 &2 of FLTM BV 154-03. Cure test specimens for 3 h at 23 +/- 2 C. Determine shear strength according to Method B of FLTM BV154-03.3.4.1 Hardness Durometer “A“(ISO 868, 3 s dwell)3.4.1.1 After Room Te

    9、mperature Curing 90(48 h at 23 +/- 2 C)3.4.2 Shear Strength(FLTM BV 154-03)Test Method: Prepare s amples per 3.4.1 except cure for 48 hat 23 +/- 2 C and expose samples as shown below. Determineshear strength according to Method B.3.4.2.1 OriginalAt 23 +/- 2 C, min 9.0 MPa3.4.2.2 At 90 +/- 2 C*, min

    10、1.5 MPa3.4.2.3 At - 40 +/- 2 C*, min 4.0 MPa*Samples shall be conditioned for 30 minutes a t thetest temperature before measurement.ENGINEERING MATERIAL SPECIFICATIONWSK-M11P54-AWP 3948-b Page 3 of 6 3.4.3 Aged Shear Strength, max loss3.4.3.1 After Heat Aging* 10 %(14 d at 90 +/- 2 C, 1 h at23 +/- 2

    11、 C)3.4.3.2 After Humidity Aging* 10 %(14 d at 38 +/- 2 C and 98 +/-2 % R.H., 1 h at 23 +/- 2 C)3.4.3.3 After Environmental Cycling* 10 %*S pecimens are exposed to 8 cycles of thefollowing sequence and then stored for 1 h at 23+/- 2 C. After four cycles, specimens are to bestored a t 23 +/- 2 C for 7

    12、2 h before runningremaining four cycles.One cycle consists of:16 h at 38 +/- 2 C and 98 +/- 2 % R.H.4 h at - 40 +/- 2 C4 h at 90 +/- 2 C3.4.2.3 After Cataplasma* 30 %Test Method:. Condition shear specimens at 23 +/- 2 C and 50+/- 5 % R.H. for 24 h. Test specimens to be wrapped with hydrophiliccotton

    13、 batting and 5 each to be put into sealedcontainers of approximately 160 mL volume f illedwith 100 mL distil led water to provide constantconditions for the following storage:. 14 d at 70 +/- 2 C. 2 h at -20 +/- 2 C. 2 h at 23 +/- 2 C. Remove wet cotton and test shear strength w ithin2 h ours of the

    14、 completion of the conditioningdescribed above.*Compared with measured value according to 3.4.2.1.ENGINEERING MATERIAL SPECIFICATIONWSK-M11P54-AWP 3948-b Page 4 of 6 3.4.5 Fatigue Resistance, Cycles x 1E6, minTest Method:. Prepare test samples per FLTM BV 154-03 except use 0.3 mmadhesive thickness.

    15、Cure for 48 h at 23 +/- C. Deter mine the fatigue resistance in a dynamic tensiletesting machine with a s inusoidal cyclic axial load and afrequency of 30 Hz. Minimum tensile load to be 10 % of maximum tensile load. Maxi mum tensile load corresponds to 30 % of originalmeasured value according to 3.4

    16、.2.1.3.4.5.1 Original 10 or failure inadhesion of paintsystem3.4.5.2 Environmental 10 or failure ini ntercoat adhesionof paint systemSpecimens are exposed to 8 cycles of the followingsequence and then stored for 1 h at 23 +/- 2 C.After four cycles, sp ecimens are to be stored 72 hat 23 +/- 2 C befor

    17、e running remaining four cy cles.One cycle consists of:. 16 h at 38 +/- 2 C and 98 +/- 2 % R.H. 4 h at - 40 +/- 2 C. 4 h at 90 +/- 2 C3.4.6 Breaking Strength and Elongation(ISO R 527, specimens Type I, 4 mmadhesive thickness)3.4.6.1 OriginalAt 23 +/- 2 *, min 9 MPa(48 h curing)Elongation at Break, m

    18、in 45 %Elastic Modulus, min 30 MPa3.4.6.2 At 90 +/- 2 C *, min 1.5 MPaElongation at Break, min 18 %Elastic Modulus, min 7 MPaENGINEERING MATERIAL SPECIFICATIONWSK-M11P54-AWP 3948-b Page 5 of 6 3.4.6.3 At - 40 +/- 2 C *, min 20 MPaElongation at Break, min 3.0 %Elastic Modulus, min 450 MPa* Sa mples s

    19、hall be conditioned for 30 minutes atthe test temperature before measurement.3.4.7 Aged Breaking Strength and ElongationAfter aging loss based on values measured per 3. 4.6, Originaltests above.3.4.7.1 At 23 +/- 2 C, max loss 30 %Elongation at Break, min 12 %Elastic Modulus, min 250 MPa3.4.6.2 At 90

    20、 +/- 2 C *, max loss 85 %Elongation at Break, min 12 %Elastic Modulus, min 10 MPa3.4.6.3 At - 40 +/- 2 C *, max loss 10 %Elongation at Break, min 2.5 %Elastic Modulus, min 750 MPa*Samples shall be conditioned for 30 minutes a t thetest temperature before measurement.Test Method: Environmental Cyclin

    21、gSpecimens are exposed to 8 cycles of the followingsequence and then stored for 1 h at 23 +/- 2 C.After four cycles, sp ecimens are to be stored 72 hat 23 +/- 2 C before running remaining four cy cles.One cycle consists of :16 h at 38 +/- 2 C and 98 +/- 2 % R.H.4 h at -40 +/- 2 C4 h at 90 +/- 2 C3.4

    22、.8 Glass Transition Point, min 31 C(ISO R537, torsion test value: Lambda max,cure test specimens for 48 h at 23 +/- 2 C)ENGINEERING MATERIAL SPECIFICATIONWSK-M11P54-AWP 3948-b Page 6 of 6 3.5 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristi

    23、cs to the material upon which approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet the spec

    24、ificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with the requ

    25、est.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WSS-M99P9999-A1.4. APPROVAL OF MATERIALSThis specification is intended to define the performance and/or propertiesof fin

    26、ished parts or systems of combined materials. An EngineeringMaterial Approved Source listin g is not applicable for this specification.Produc t Engineering materials referenced in this document and/or theaffected engineering drawing, which require prior Engine ering approval, aresh own in the Engineering Material Approved Source List under thespecification cited.5. GENERAL INFORMATIONThe in formation below is provided for clarification in meeting therequirements of these specifications.5.1 Affected Material Specifications:WSK-M11P54-A1 relates to ESK-M2G365-A1 and ESK-M2G365-A2.


    注意事项

    本文(FORD WSK-M11P54-A-2013 PERFORMANCE SEMISTRUCTURAL ADHESIVE POLYURETHANE METAL TO METAL TWO COMPONENT TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(priceawful190)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开