欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSF-M3D165-A-2006 UNSATURATED POLYESTER (UP) 12% GLASS FIBER REINFORCED HIGH HEAT RESISTANT COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%玻璃纤维增强的不饱和聚酯.pdf

    • 资源ID:750188       资源大小:246.50KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSF-M3D165-A-2006 UNSATURATED POLYESTER (UP) 12% GLASS FIBER REINFORCED HIGH HEAT RESISTANT COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%玻璃纤维增强的不饱和聚酯.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2006 08 16 Revised Inserted 3.0, Deleted 3.1, 3.2, 3.3, 3.8, 3.9, 4 1994 01 31 Completely Revised NGA1E10370437001 A. Vallabhanath 1992 03 19 Released DF00E00107002134 A. Vallabhanath L. P. Rumao Printed copies are uncontrolled Copyright 2006

    2、, Ford Global Technologies, LLC Page 1 of 5 UNSATURATED POLYESTER (UP), 12% GLASS FIBER WSF-M3D165-A REINFORCED, HIGH HEAT RESISTANT COMPRESSION MOLDING COMPOUND 1. SCOPE The material defined by this specification is a natural color glass reinforced unsaturated polyester (UP). This material is highl

    3、y filled with calcium carbonate and mineral fillers. 2. APPLICATION This specification was released originally for material used for brush holders. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requireme

    4、nts For Production Materials (WSS-M99P1111-A). 3.1.1 All requirements of this specification, identified by symbol (s), shall be met with data representing 3 sigma values. 3.4 MOLDING COMPOUND (s) 3.4.1 Filler Content 3.4.1.1 Ash Content 45 - 50% (ISO 3451/1, Method A 1 h at 650 +/- 25 C) 3.4.1.2 Gla

    5、ss Fiber Content, by weight 11 - 13% Test Method: ISO 3451/1, Method B, 1 h at 650 +/- 25 C, except use 5% by volume hydrochloric acid solution for 15 minutes. Rinse and filter the glass fibers several times with distilled water (use of glass filter with 50 micrometre size pores, maximum is recommen

    6、ded) before drying in an oven for 2 h at 120 +/- 2 C. After cooling, weigh the crucibles and calculate the percent glass fibers. 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on compression molded test specimens. The following

    7、dimensions are required: A. 150 minimum x 10 x 4.0 +/- 0.2 mm (Tensile Bar) B. 120 x 10 x 4.0 +/- 0.2 mm C. 13 x 13 x 25 mm (Compressive Strength Bar, ASTM D 695) ENGINEERING MATERIAL SPECIFICATION WSF-M3D165-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 5

    8、 Specimens with shorter dimensions shall be cut from the center portion of the test specimen A and/or B. The specimens shall be prepared under optimum conditions as defined by the manufacturer of raw material. No annealing allowed. 3.5.2 Density 1.76 - 1.85 g/cm3 (ISO 1183, Method A) (s) 3.5.3 Tensi

    9、le Strength at Max Load, min 32 MPa (ISO R 527, 150 x 10 x 4.0 +/- 0.2 mm specimen, 5 mm/minute test speed) (s) 3.5.4 Flexural Modulus, min 12 GPa (ISO 178, 80 x 10 x 4.0 +/- 0.2 mm specimen, 64 mm support span, 2 mm/minute test speed) (s) 3.5.5 Flexural Strength, min 82 MPa (ISO 178, 80 x 10 x 4.0

    10、+/- 0.2 mm specimen, 64 mm support span, 2 mm/minute test speed) (s) 3.5.6 Compressive Strength, min 100 MPa (ASTM D 695, 13 x 13 x 25 mm specimen, 1.3 mm/minute test speed) 3.5.7 Shear Modulus at 23 C 3.9 - 4.6 GPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain lev

    11、el below 1%. Specimen approx. 60 x 10 x 4.0 +/- 0.2 mm cut from the center of specimen A. Specimen length between clamps 35-40 mm. Soak time at each temperature interval - 3 minutes minimum) Additionally, a Shear Modulus vs. Temperature curve shall be plotted for -50 to +280 C temperature range, at

    12、5 C minimum intervals. The plotted curve must be within tolerance range shown on page 5. (s) 3.5.8 Impact Strength, Izod, min (ISO 180/1A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens for each test) 3.5.8.1 At 23 +/- 2 C 31.3 kJ/m2 3.5.8.2 At -40 +/- 2 C 31.3 kJ/m2 The test specimens must be cond

    13、itioned for minimum of 6 h at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold box, if not possible, test can be conducted outside, but within 5 s. ENGINEERING MATERIAL SPECIFICATION WSF-M3D165-A Printed copies are uncontrolled Copyright 200

    14、6, Ford Global Technologies, LLC Page 3 of 5 (s) 3.5.9 Heat Deflection Temperature, min 300 C (ISO 75, Method A, 120 x 10 x 4.0 +/- 0.2 mm specimen, 0.32 +/- 0.01 mm deflection. At 1.82 MPa) (s) 3.5.10 Water Absorption, max 0.10% (ISO 62, 24 h, 24 h, boiling water, injection molded multipurpose spec

    15、imen 150 min x 10 x 4.0 +/- 0.2 mm) 3.5.11 Heat Aging Performance (ISO 188, except 150 +/- 50 air changes/h, 1000 h at 200 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.5.11.1 Tensile Strength at +/- 25% Load Change, max (Test Method per para

    16、 3.5.3) 3.5.11.2 Flexural Strength Change, max +/- 25% (Test Method per para 3.5.5) 3.5.11.3 Impact Strength, Izod Change +/- 25% (Test Method per para 3.5.8.1, specimens to be notched before heat aging) 3.6 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute Does Not Ignite (DNI) The spec

    17、imen size required for material approval is 355 x 100 x 3.2 +/- 0.1 mm with a smooth surface. 3.7 SPECIAL REQUIREMENTS (s) 3.7.1 Dielectric Strength, min 16.1 kV/mm (IEC 243/ASTM D 149, in insulating oil, 3.2 +/- 0.2 mm thick specimen, short time) ENGINEERING MATERIAL SPECIFICATION WSF-M3D165-A Prin

    18、ted copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 4 of 5 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 COEFFICIENT OF LINEAR THERMAL EXPANSION (ASTM D 696) 5.1.1 Para

    19、llel to Flow 27.5-5/ C 5.1.2 Perpendicular to Flow 27.5-5/ C 5.2 MOLD SHRINKAGE (ISO 2577, 120 x 10 x 4.0 +/- 0.2 mm compression molded specimen, after 48 h at room temperature) 5.2.1 Molding Shrinkage . After 48 h at 23 +/- 2 C 0.20% 5.2.2 Post Shrinkage . After 48 h at 120 C 0.21% 5.3 HARDNESS, BARCOL, typical 1.3 - 1.4 mm (ASTM D 2583) penetration 5.4 RECYCLING CODE UP- (GF+M) 60 ENGINEERING MATERIAL SPECIFICATION WSF-M3D165-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 5 of 5


    注意事项

    本文(FORD WSF-M3D165-A-2006 UNSATURATED POLYESTER (UP) 12% GLASS FIBER REINFORCED HIGH HEAT RESISTANT COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《12%玻璃纤维增强的不饱和聚酯.pdf)为本站会员(ownview251)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开