欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY TO BE USED WITH FORD WSS-M99P1111-A 《车内级排放鉴定标签 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:750098       资源大小:70.03KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY TO BE USED WITH FORD WSS-M99P1111-A 《车内级排放鉴定标签 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 01 25 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.10, 4 1991 02 13 Released NEO1-E-10000474-091 E. J. Duda Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 2 LABEL, EMISSION CERTIFICATION, INTERIO

    2、R QUALITY WSE-M3G193-A2 1. SCOPE The material defined by this specification is a polyester film with a pressure sensitive adhesive protected by a suitable release line. 2. APPLICATION This specification was released originally for labels used to state the vehicle emission control information as requ

    3、ired by the Federal regulations or as specified on the engineering drawing. It is applied to the mounting surface by removing the release paper and pressing firmly into place. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the

    4、 Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 APPEARANCE Shall be free of streaks, blisters, wrinkles, ragged edges, smeared printing, and any other surface imperfections which will make them unsuitable for the intended usage. The design and color shall be as specifi

    5、ed on the engineering drawing. 3.5 PREPARATION OF LABELS ON GLASS PANELS Clean glass panels with alcohol and allow the surface to dry. Place the label on the glass panels with a 2.0 kg rubber roller with one edge or side not adhered (about 20% of the total area). Condition for 24 h minimum at 23 +/-

    6、 2 C and 50 +/- 5% relative humidity. 3.6 ORIGINAL ADHESION, min 600 N/m width (ASTM D 1000, 180 peel) 3.7 ENVIRONMENTAL TESTING OF PANEL ASSEMBLY Test shall be performed immediately after removal from the conditioning environment. After each of the environmental exposures, the label must not show e

    7、vidence of delamination, loss of printing or any other effect which would detract from its proper function or appearance. 3.7.1 Direct a stream of air 400 - 500 kPa pressure with a 2.4 mm diameter orifice and at a distance of approximately 75 mm from the decals edge for 3 minutes at a right angle to

    8、 the surface and then for 3 minutes at a 10 angle to its edge. 3.7.2 Humidity cabinet for 168 h at 38 +/- 2 C and 98 +/- 2%relative humidity. Adhesion - 180 Peel 385 N/m width ENGINEERING MATERIAL SPECIFICATIONWSE-M3G193-A2Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC

    9、 Page 2 of 2 3.7.3 Hold panel for 1 h at -40 C, then expose for 1 h at 99 +/- 2 C. Repeat for 4 cycles. Maximum shrinkage 5%. Adhesion - 180 Plane 825 N/m width 3.7.4 Weathering Resistance, min 225 kJ (SAE J1885) Adhesion - 180 Peel 600 N/m width 3.8 FOGGING (FLTM BO 116-03) Fog Number, min 60 The formation of droplets or coalescence into a clear film is cause for rejection. 3.9 LABEL STRENGTH During installation, the label must not break, tear or deface. The release backing shall not tear or delaminate while being removed from the label.


    注意事项

    本文(FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY TO BE USED WITH FORD WSS-M99P1111-A 《车内级排放鉴定标签 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(bonesoil321)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开