欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD WE953-1996 GENERAL SPECIFICATIONS ASSEMBLY INFORMATION MECHANICAL AND PERFORMANCE REQUIREMENTS FOR SINGLE THREAD SPRING NUTS《单螺纹弹簧螺母的一般技术条件、装配信息、机械和性能要求》.pdf

    • 资源ID:748529       资源大小:18.75KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD WE953-1996 GENERAL SPECIFICATIONS ASSEMBLY INFORMATION MECHANICAL AND PERFORMANCE REQUIREMENTS FOR SINGLE THREAD SPRING NUTS《单螺纹弹簧螺母的一般技术条件、装配信息、机械和性能要求》.pdf

    1、FORD WORLDWIDE FASTENER STANDARDDate: 1996-10-01Engineering Standards & 1 of 2 Printed copies are uncontrolled .Systems Engineering (ESSE)WE 953General Specifications, Assembly Information, Mechanical and Performance Requirements for Single ThreadSpring Nuts1. SCOPE. This standard covers performance

    2、 and other requirements for single thread form spring nutsdesigned for assembly on panels 0.6 to 3.8 thick.NOTE: The design of the thread impression, retaining feature and other features may vary betweenmanufacturers, provided all requirements of this standard are met.1.1 REFERENCES.ISO 683/18 - Hea

    3、t-treated steels, alloy steels and free cutting steels - Part 18: Wroughtunalloyed steels in the normalized, or normalized and cold-drawn, or hot-rolled and cold-drawn condition.ISO 6932 - Cold reduced carbon steel strip with a maximum carbon content of 0.25%.2. MATERIAL AND HEAT TREATM ENT.2.1 MATE

    4、RIAL. The material shall be spring steel, the specific grade of material shall be at thediscretion of the manufacturer to meet the performance requirements and provide adequateductility.2.2 HEAT TREATMENT. Harden and Temper to HV420 - 520 or Austemper to HV500 - 570.3. PERFORMANCE.3.1 ASSEMBLY AND R

    5、ETENTION. Spring nuts shall preassemble onto steel test plates of thicknessequal to the two extremes of the panel range specified for the nut to be tested. The maximuminstallation force during the assembly of the spring nut shall be 55 N. The minimum force to thenremove the spring nut shall be 2 N.3

    6、.2 TORQUE AND CLAMP FORCE TEST. A spring nut shall be assembled on a test panel (SeeFigure 1 and Table 2) of thickness equal to the maximum thickness of the panel range specified forthe nut to be tested with a device suitable for measuring clamp force incorporated. A test screw(See Clause 4) shall t

    7、hen be driven into the assembled spring nut until the installation torquespecified in Table 1 is achieved. The clamp force shall not be less than the minimum clamp forcespecified in Table 1.Upon disassembly, the thread impression shall return to a condition that will accept re-entry of thescrew.3.3

    8、DESTRUCTIVE TORQUE TEST. Using the same method as described in Clause 3.2, but withouta device for measuring clamp force, a spring nut shall be assembled on a test panel (See Figure 1and Table 2) of thickness equal to the maximum thickness of the panel range specified for the nutto be tested and a t

    9、orque applied to a test screw (See Clause 4) driven into the spring nut. Torqueto cause failure shall not be less than the value specified in Table 1.3.4 TENSILE TEST. Using the same assembly procedure as described in Clause 3.2 but replacing theclamp force measuring device with a tensile load measu

    10、ring device, a test screw (See Clause 4)shall be driven into the spring nut but not tightened to induce any pre-load. A tensile load shallnow be applied to the screw until the spring nut fails. The tensile load to cause failure shall not beless than the value specified in Table 1.4. TEST SCREW. The

    11、test screw shall be Type AB as specified in WD900 and shall not be less than 25mmlong. The surface coating shall be S309 in accordance with WX100.Table 1. Performance requirementsScrew Size Installation TorqueNmClamp Force kN MinimumDestructive TorqueNmMinimum TensileStrength kNST3.5 1.35 1.06 1.92

    12、2ST4.2 2.25 1.67 2.82 2.22ST4.8 3.47 2.3 5.2 3.53ST6.3 6.78 3.34 9.04 4FORD WORLDWIDE FASTENER STANDARDDate: 1996-10-01Engineering Standards & 2 of 2 Printed copies are uncontrolled .Systems Engineering (ESSE)WE 953General Specifications, Assembly Information, Mechanical and Performance Requirements for Single ThreadSpring NutsTable 2. Test panelScrew Size Distance from Edge AHole Diameter GPanel RangeST3.5 0.75 x B 4.8 SeeST4.2 Where B is the spring 5.6 ClauseST6.3 nut throat depth 7.9 3MATERIAL: Cold rolled steel to ISO 6932 or ISO 683/18.Figure 1. Test panel


    注意事项

    本文(FORD WE953-1996 GENERAL SPECIFICATIONS ASSEMBLY INFORMATION MECHANICAL AND PERFORMANCE REQUIREMENTS FOR SINGLE THREAD SPRING NUTS《单螺纹弹簧螺母的一般技术条件、装配信息、机械和性能要求》.pdf)为本站会员(postpastor181)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开