欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD SK-M99G9511-A-2006 SINGLE PLY DEADENER SHEETING MOLDED HEAT FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《可热熔的模制单层隔音板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:748169       资源大小:109.05KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD SK-M99G9511-A-2006 SINGLE PLY DEADENER SHEETING MOLDED HEAT FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《可热熔的模制单层隔音板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2006 09 26 Revised Inserted 3.0; Deleted 3.19 except use 1.5 mm thick test panels. 2) Expose assemblies at 90 +/- 2 C air temperature for 2 weeks. 3) After cooling to room temperature test adhesion according to FLTM BV 151-02, Method A, claus

    2、e 5 to 8; Load B. 3.8 COMPATIBILITY WITH PRODUCTION PAINTS The paint must form a uniform and closed film over the material surface. Test Method: 1) Test assembly preparation according to clause 3.6, section 1, except use 100 x 300 mm test panels and test material at a size of 80 x 280 mm. 2) Enamel

    3、with a light colored production paint according to FLTM BI 103-02. 3.9 PAINT STAINING No staining or other deleterious effects. Test Method: Condition a test assembly prepared as described under clause 3.8 for 24 hours at room temperature. Mask one half of the enameled test material and expose for 9

    4、6 hours in the Fluorescent Sunlamp Cabinet (see FLTM BU 152-02), with the enameled test material facing the light source. Examine the exposed and unexposed portions of the test specimen. 3.10 CORROSION RESISTANCE No corrosion Test Method: 1) Preparation of test assembly according to clause 3.8, sect

    5、ion 1 and 2. 2) After 24 hours at room temperature test according to ASTM B 117 for 240 hours. 3) Remove a 30 mm wide strip from the longer edge of the test specimen and examine for corrosion. ENGINEERING MATERIAL SPECIFICATION SK-M99G9511-A Printed copies are uncontrolled Copyright 2006, Ford Globa

    6、l Technologies, LLC Page 3 of 4 3.11 RESISTANCE TO HUMIDITY No corrosion Test Method: 1) Preparation of test assembly according to clause 3.8, section 1 and 2. 2) After 24 hours at room temperature expose to 98 +/- 2% relative humidity and 38 +/- 2 C for 500 hours. 3) Examine according to clause 3.1

    7、0, section 3 of test method. 3.12 ENVIRONMENTAL CYCLING No shrinkage, no blistering, no cracking Test Method: 1) Prepare test assemblies according to clause 3.6, section 1 of test method. 2) Enamel with a light colored production paint according to FLTM BI 103-02. 3) After 24 hours at room temperatu

    8、re expose test assemblies 3 times to the following cycle in the succession as outlined below. 16 h at 38 +/- 2 C and 98 +/- 2% relative humidity 3 h at 90 +/- 2 C 3 h at -40 +/- 2 C Examine after cooling to room temperature. 3.13 WASH AND PHOSPHATING SOLUTION RESISTANCE No evidence of dissolution of

    9、 test material or lifting from panel. Test Method: 1) Test assembly preparation according to clause 3.6, section 1 of test method; except 250 x 60 mm test panels and 240 x 40 mm test material. 2) After conditioning for 2 hours at room temperature expose test assemblies one after another in each wash

    10、 and phosphating solution of the affected plant where this material is to be used and maintain for 15 minutes at 60 +/- 2 C. 3) After 15 minutes at room temperature expose to heat according to FLTM BV 150-05, table 1, minimum curing cycle, phase 2. 4) Examine after cooling to room temperature. 3.14

    11、TENSILE ADHESION, min 200 N/cm2 (FLTM BV 154-03, Method A, test assembly preparation according to section I, x = 4 mm, cohesion failure not required) ENGINEERING MATERIAL SPECIFICATION SK-M99G9511-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 4 of 4 3.15 PALLET

    12、IZING The material shall separate easily upon peeling by hand without tearing. Test Method: 1) Cut 5 specimens 100 x 100 mm from material under test and determine weight and thickness per specimen. 2) Ply-up and cover with an aluminum plate of same size. 3) Load with a dead weight equaling a ply-up

    13、height of 100 mm minus weight of 5 specimen cover plate. 4) Expose assembly in a mechanical convection oven maintained at 50 +/- 2 C for 2 weeks. Cool to room temperature, remove weight and cover plate and examine as described above. 3.16 DAMPING FACTOR, min eta = 0.05 (FLTM EU-BV 060-01, fuse accor

    14、ding to clause 3.6, section 1) 3.17 HEALTH HAZARDS AND ODOR The material must not contain any ingredients (matter), which, under normal production conditions, could lead to health hazards such as skin rash or irritation (dermatitis), irritation of the mucous membranes, difficulties in breathing etc.

    15、 The material shall be free from objectionable odors both as received and after storage. 3.18 QUALITY The material shall be of uniform quality free from foreign material and properties detrimental to normal production use. It shall not cause excessive soiling of handlers in normal production use. 5.

    16、 GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 STORAGE STABILITY (From date of receipt at Ford Motor Company) Minimum 6 months when stored between 5 C and 28 C. 5.2 HEIGHT IN STORAGE As recommended by supplier.


    注意事项

    本文(FORD SK-M99G9511-A-2006 SINGLE PLY DEADENER SHEETING MOLDED HEAT FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《可热熔的模制单层隔音板 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(花仙子)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开