欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD SK-M99G9510-A-2006 DAMPING SHEET HEAT FUSIBLE HEAT RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐热可热熔型减震板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:748168       资源大小:107.25KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD SK-M99G9510-A-2006 DAMPING SHEET HEAT FUSIBLE HEAT RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐热可热熔型减震板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 30 Revised Inserted 3.0; Deleted 3.13, 3.15 Format Updated 1974 10 31 Revised Revised Sheet 1-5 B/CP7049TP 1974 12 06 Released SM/ET0759TP Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 5 DAMPIN

    2、G SHEET, HEAT FUSIBLE, HEAT RESISTANT SK-M99G9510-A 1. SCOPE The material defined by this specification is a heat resistant, moldable, heat fusible filled damping sheet based in plastic or bitumen/rubber with an anti-blocking surface finish or with release paper. 2. APPLICATION The material is used

    3、for structure borne noise damping in the passenger compartment. It is used in areas where a good heat resistance is required. The material is applied before passing through the paint oven or as specified on the Engineering Drawing. 3. REQUIREMENTS The material shall be conditioned for a minimum of 2

    4、4 hours at 23 C +/- 2 C and 50% +/- 5% relative humidity prior to test. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producer must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 COLOR Black 3.2 SOLIDS min. 99% (FLTM BV 1

    5、50-10) 3.3 ASH max. 85% (FLTM BV 150-10) 3.4 THICKNESS (mm) 1.8 2.3 (ASTM D 374, Method A) or as specified on Engineering Drawing 3.5 MASS (kg/m2) max. 6.0 (at 2 mm thickness) 3.6 FORMABILITY The material must sag into the recessed area of the test panel. Test Method 1. Apply pieces of material unde

    6、r test as shown in Fig. 1 to test panels prepared according to FLTM BI 120-01. ENGINEERING MATERIAL SPECIFICATIONSK-M99G9510-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 5 2. Expose test assemblies separately acc. to FLTM BV 150-05 a. Table 3, Min. Curing

    7、 Cycle b. Table 1, Max Curing Cycle, Phase 2 3. Examine after cooling to room temperature. 3.7 HEAT STABILITY The material shall fuse to the substance without evidence of blistering or cracking. Test Method 1. Apply a 280 x 280 mm piece of material under test to a 300 x 300 mm test panel prepared ac

    8、cording to FLTM BI 120-01. Expose test assemblies to Min. Curing Cycle, Table 3 of FLTM BV 150-05. 2. Expose subsequently according to FLTM BV 150-05, Table 1, Max Curing Cycle, Phase 2. 3.8 PEEL ADHESIVE min. 8 N/cm Test Method 1. Apply test material of 30 x 300 mm to test panels prepared according

    9、 to FLTM BI 120-01 and fuse according to clause 3.6, section 2. 2. After 24 h at room temperature lift the test material from the panel in a length of 50 mm, than peel test material from panel under an angle of 90 at a rate of 25 mm/min. 3. Record the peel strength. 3.9 RESISTANCE TO SLUMPING The ma

    10、terial thickness at any point shall not be less than 50% of original thickness. Test Method 1. Apply test material to panels as shown in Fig. 2, prepared according to FLTM BI 120-01, and expose to heat in horizontal position as described under clause 3.7, section 1, of test method. 2. Expose prepare

    11、d test assemblies at an angle of 55 (Fig. 2) to heat as described under clause 3.7, section 2. of test method. 3.10 Cold Adhesive after Ageing No chipping or detachment Test Method 1. Apply 280 x 300 mm pieces of test material to 300 x 300 1.5 mm test panels prepared according to FLTM BI 120-01. 2.

    12、Expose test assemblies separately to heat according to FLTM BV 150-05: a. Table 3, Min. Curing Cycle b. Table 1, Max. Curing Cycle, Phase 2. ENGINEERING MATERIAL SPECIFICATIONSK-M99G9510-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 5 3. Store test assembl

    13、ies at 90 C +/- 2 C for 14 days. 4. After cooling to room temperature test adhesive acc. to FLTM BV 151-02, Method B, clause 5 to 8, Load A. -30 C +/-1 C. 3.11 DAMPING FACTORS: will be added later (FLTM BV 060-01, heat fuse According to FLTM BV 150-05, Table 1, Maximum Curing Cycle, Phase 1) 3.12 PA

    14、LLETIZING The material shall separate easily upon peeling by hand without tearing. Test Method: 1. Cut from material under test 5 specimens 100 x 100 mm and determine weight and thickness per specimen. 2. Ply up and cover with an aluminum plate of same size. 3. Load with a dead weight equaling a pli

    15、ed up height of 600 mm minus weight of 5 specimens and cover plate. 4. Expose assembly in a mechanical convection oven maintained at a temperature of 35 C +/- 2 C for 2 weeks. Cool to room temperature, remove weight and cover plate and examine as described above. 3.14 HEALTH HAZARDS AND ODOR The mat

    16、erial must not contain any ingredients (matter) which, under normal production conditions, could lead to health hazards such as skin rash or irritation (dermatitis), irritation of the mucous membranes, difficulties in breathing etc. The material shall be free from objectionable odors both as receive

    17、d and after storage. 5. GENERAL INFORMATION 5.1 STORAGE STABILITY (from date of receipt at FMC) Minimum 6 months when stored between 5 C and 28 C. 5.2 HEIGHT IN STORAGE As recommended by supplier. ENGINEERING MATERIAL SPECIFICATIONSK-M99G9510-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 4 of 5 ENGINEERING MATERIAL SPECIFICATIONSK-M99G9510-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 5 of 5


    注意事项

    本文(FORD SK-M99G9510-A-2006 DAMPING SHEET HEAT FUSIBLE HEAT RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《耐热可热熔型减震板 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(bowdiet140)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开