欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM EU-AP 050-03-2001 DETERMINATION OF ANTI-DEGRADANTS IN RUBBER BY THIN-LAYER CHROMATOGRAPHY《薄层色谱法测定橡胶中的阻降解剂的测定》.pdf

    • 资源ID:747752       资源大小:39.82KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM EU-AP 050-03-2001 DETERMINATION OF ANTI-DEGRADANTS IN RUBBER BY THIN-LAYER CHROMATOGRAPHY《薄层色谱法测定橡胶中的阻降解剂的测定》.pdf

    1、 FORD LABORATORY TEST METHOD EU-AP 050-03 Date Action Revisions 2001 01 31 Revised Editorial no technical change A. Cockman 2000 04 19 Editorial no technical change A. Cockman 1993 01 04 Printed copies are uncontrolled Page 1 of 5 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF ANTI-

    2、DEGRADANTS IN RUBBER BY THIN LAYER CHROMATOGRAPHY Application This procedure describes a method for “fingerprinting“ the anti-degradants (e.g. anti-ozonants, anti-ozidants, anti-fatigue agents) in rubber compounds, and as such is used to check consistency of formulation for specific applications whe

    3、re close control is required. The method may also be used in certain cases for comparison work (e.g. to measure loss of anti-degradant from rubber due to environmental factors). The method is not intended to be used, either for identification of anti-degradants or to predict the performance of a rub

    4、ber compound, unless a degree of caution in interpretation is applied. Equipment Required Thin Layer Plates Silica gel 60 F 254 precoated size 20 x 20 cm; layer thickness 0.25 mm. Sources: Merck, Andermann, BDH Developing Tank with Lid 22 x 6 x 21 mm or close approximation. Syringe 5.0 l capacity Sp

    5、otting Guide (optional) Aerosol Spray Unit A fine spray type as supplied for use in chromatography. Spray Reagent A freshly prepared 1 % solution of 2:6 dibromo-p-benzoquinone-4-chlorimine in industrial methylated spirit, unless otherwise stated on appropriate specification. *Developing Solvent A mi

    6、xture of the following: Benzene 100 parts Ethyl acetate 5 parts Acetone 2 parts FORD LABORATORY TEST METHOD EU-AP 050-03 Page 2 of 5 Copyright 2001, Ford Global Technologies, Inc. Reference solutions Solutions of anti-degradant are used for reference purposes in order to ensure consistency of the te

    7、chnique and for comparisons of spot intensity. An 0.1 % solution in acetone of one or more of the following may be used unless otherwise required: Suppliers N, NdiphenylpPhenyleneDiamine ICI, Monsanto N-Phenyl-B-Naphthylamine Bayer, ICI, Monsanto Acetone/Diphenylamine Reaction Product ICI, Monsanto

    8、6-Ethoxy-2,2,4-Trimethyl-1,2-Dihydroquinoline Monsanto Standard Laboratory Equipment Such as filter paper, flasks, soxhlet, etc. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidi

    9、ty for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Extract the rubber compound (1.0 g) for 24 h in acetone. See ASTM D 297 for details. Concentrate the extract to 3 mL. 2. Prepare the developing tank by lining with filter paper sa

    10、turated with the developer solution, and maintain a depth of approx 10 mm at the bottom of the tank. (Tank must be cleaned and solution changed once per 2 days minimum). Tank should be covered and allowed to stand overnight for the atmosphere to equilibrate. 3. Mark out TLC plate with pencil as show

    11、n on the accompanying sketch. 4. Preheat plate for 1 h at 75 C then cool. 5. Using syringe, spot 5 l of extract solution onto plate as shown on line B. Do likewise with the reference solution(s) ensuring that there is adequate spacing (12 mm min) between spots. To keep spot size to a minimum it is h

    12、elpful to dry during spotting with clean pressurized air. FORD LABORATORY TEST METHOD EU-AP 050-03 Page 3 of 5 Copyright 2001, Ford Global Technologies, Inc. 6. Immerse the plate in the tank and allow to stand until the developer solution has eluted as far as line A, ensuring that the tank is sealed

    13、 by means of the lid. 7. Remove the plate from the tank, allow 5 minutes to dry, then place in oven for 2 minutes at 100 C. Allow to cool. 8. Place the plate under a fume hood and spray evenly with reagent, noting the formation of coloured spots, and withdraw the spray when no further intensificatio

    14、n of the spot occurs. Do not overspray as the background will darken, and lack of contrast will result. 9. Allow the plate to stand for 16 h minimum, then assess results. Evaluation An assessment of each spot on the plate is made according to: (a) Colour (b) Intensity (or Area) (c) R Value = a (see

    15、sketch) b Assessments are normally made on a qualitative basis, by making comparisons on the same plate. Plates may be retained as standards, however, but due allowance must be made for any change in storage. (Dulling and darkening of the plate can be almost eliminated if contact with air and light

    16、is avoided). A more permanent record such as coating with clear lacquer, or same size colour photographs, is essential where a more quantitative comparison is required. *Alternative Method can be used if stated on appropriate specification or other document, if there is unsatisfactory separation of

    17、the desired spots. The procedure is identical except for: Spray Reagents (1) A freshly prepared 1 % solution of 2.6 dichloro-p-benzoquinone-4-chlorimine in industrial methylated spirit. (2) A freshly prepared 2 % solution of sodium tetraborate in 40 % ethanol (in water). FORD LABORATORY TEST METHOD

    18、EU-AP 050-03 Page 4 of 5 Copyright 2001, Ford Global Technologies, Inc. Developing Solvent A mixture of: Benzene 48 % n-Hexane 48 % Acetone 4 % Procedure Detail Allow 5 minutes between application of the two spray reagents, then heat for 10 minutes at 100 C and cool. Chemicals, materials, parts, and

    19、 equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD EU-AP 050-03 Page 5 of 5 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF ANTI-DEGRADANTS IN RUBBER BY THIN LAYER CHROMATOGRAPHY Caution: The rubber additives/chemicals should be handled with care, and contact with the skin avoided.


    注意事项

    本文(FORD FLTM EU-AP 050-03-2001 DETERMINATION OF ANTI-DEGRADANTS IN RUBBER BY THIN-LAYER CHROMATOGRAPHY《薄层色谱法测定橡胶中的阻降解剂的测定》.pdf)为本站会员(terrorscript155)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开