欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM BU 105-01-2000 STAINING TEST FOR ADHESIVES AND PRESSURE SENSITIVE TAPES (Replaces FLTM BU 005-01)《胶粘剂和压敏胶带的着色试验 替代FLTM BU 005-01[替代 FORD FLTM BU 005-01]》.pdf

    • 资源ID:747529       资源大小:27.05KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM BU 105-01-2000 STAINING TEST FOR ADHESIVES AND PRESSURE SENSITIVE TAPES (Replaces FLTM BU 005-01)《胶粘剂和压敏胶带的着色试验 替代FLTM BU 005-01[替代 FORD FLTM BU 005-01]》.pdf

    1、 FORD LABORATORY TEST METHOD BU 105-01 Date Action Revisions 2000 11 13 Revised Editorial no technical change A. Cockman 1992 08 10 Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. STAINING TEST FOR ADHESIVES AND PRESSURE SENSITIVE TAPES Application This pro

    2、cedure is used to test adhesives and pressure sensitive tapes for staining development when used in trim assemblies. Assemblies of the materials are exposed to heat and artifi cial sunlight to simulate conditions under which staining may occur. Apparatus Requires Fluorescent Sunlamp Cabinet - or equ

    3、ivalent A modified oven equipped with four Westinghouse FS 20 T - 12 fluorescent sunlamps is required. The oven shall be maintaine d at 63 +/ - 2 C for this test. Oven Grieves Hendry, Model PL - 1, 1000 watts O.D. - 750 mm wide, 625 mm deep, 600 mm high I.D. - 712 mm wide, 600 mm deep, 512 mm high 1

    4、10 V, AC, 50 - 60 cycle, single phase motor The oven is to be equipped with thermostat control and red pilot light. An oven stand is optional. Sunlamp Fixture 20 gage steel box with screw cover Two two - lamp, 20 watt high power factor ballasts Four fluorescent starter assemblies Cover - 20 gage ste

    5、el with Alzak aluminum reflector overlay Four pairs fluorescent lamp holders Rear of box shall be provided with four 1/4 - 20 mounting studs and screened ventilation openings Four FS 20 T - 12 fluorescent sunlamps The above sunlamp fixture to be completely installed in oven. FORD LABORATORY TEST MET

    6、HOD BU 105-01 Page 2 of 3 Copyright 2000, Ford Global Technologies, Inc. Adhesive Film Applicator A scraper similar to the one shown below is used to spread the adhesive in a film 25 mm wide and 0.25 mm thick. Material - Low Carbon Steel Roller A steel roller 82.5 +/ - 2.5 mm diameter and 45 +/ - 1.

    7、0 mm in width, covered with rubber approximate ly 6 mm thick and having a durometer hardness of 80 +/ - 5. The weight of the roller proper which applies pressure to the specimen shall be so constructed that the weight of the handle is not added to the weight of the roller during use. (ASTM D 1000).

    8、Steel Panels Phosphate coated only - 75 x 200 mm Phosphate coated, primed and enameled - 75 x 200 mm Prepare panels as described in Ford Laboratory Test Method BI 109 - 01. Use method “C“ for painted panels. Conditioning and Test Conditions All test values indicated herein are based on material cond

    9、itioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure Tapes 1. P repare freshly enameled steel panels with White, or Light Blue, or their replacement color

    10、s. Prime and enamel panels as described in Ford Laboratory Test Method BI 103 - 02, Method “C“. 2. Place a tape specimen 25 x 175 mm on the center portion of each of the painted panels. Use light finger pressure to give intimate contact and then roll once forward and back with the 2 kg roller. 3. Ma

    11、sk off 50 mm of the tape and panel with aluminum foil and expose the assemblies in the sunlight cabinet at a distance of 300 mm from the lamps for the time required by the material standard. FORD LABORATORY TEST METHOD BU 105-01 Page 3 of 3 Copyright 2000, Ford Global Technologies, Inc. 4. After 24

    12、hours exposure, strip and cut off a 50 mm portion of the exposed tape specimens and again place the assemblies in the sunlamp cabinet for 24 hours. 5. Remove the aluminum foil, compare with the exposed areas and examine for any migration staining of the adhesive mass through the cloth tapes or onto

    13、the areas of the panel immediately adjacent to the contact areas of the tape. Examine the 50 mm areas where the tapes were re moved after the first 24 hours exposure and note any contact stain which appeared after the second 24 hours exposure. Adhesives Single Coat Application 1. Prepare enameled pa

    14、nels of both colors as described under Tapes Step No. 1. 2. Apply a 25 mm wid e and 0.25 mm thick wet film of the adhesive over the length of the left half of each panel. Brush a similar film of adhesive on the right side of each panel to simulate production application. 3. Allow a 1 minute open tim

    15、e, then place a 25 mm by 150 mm section of M2F37 FDA, Vinyl Coated Headlining, over each of the adhesive films, spreading lightly with the flat portion of the finger to obtain intimate contact. (See note.) 4. Condition the assembly for 16 hours at 23 +/ - 2 C, then mask off one half of each assembly

    16、 with aluminum foil. 5. Expose in the sunlight cabinet 300 mm from the lamps for the time required by the material standard. 6. Remove the aluminum foil and compare with the exposed area. Report any adhesive staining or discoloration of th e headlining. Double Coat Application 1. Apply a 25 mm wide

    17、and 0.25 mm thick wet film of adhesive over the length of the left half of a phosphate coated panel. Brush a similar film of adhesive over the other half of the panel to simulate production app lication. 2. Brush adhesive over the Naugahyde backing surface. 3. Allow a 1 minute open time, then place

    18、25 mm by 150 mm sections of M2F9, Naugahyde, over each of the adhesive films, spreading lightly with the flat portion of the finger to obtain intima te contact. (See note.) 4. Follow Steps No. 4 and 5 under Single Coat Application. 5. Remove the aluminum foil and compare with the exposed area. Repor

    19、t any adhesive staining or discoloration of the M2F9 Naugahyde. Note: Any immediate wetting through the headlining or the Naugahyde by the adhesive is the result of too much adhesive and is not to be construed as staining or discoloration. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each p arty is responsible for determining proper use and handling in its facilities.


    注意事项

    本文(FORD FLTM BU 105-01-2000 STAINING TEST FOR ADHESIVES AND PRESSURE SENSITIVE TAPES (Replaces FLTM BU 005-01)《胶粘剂和压敏胶带的着色试验 替代FLTM BU 005-01[替代 FORD FLTM BU 005-01]》.pdf)为本站会员(bonesoil321)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开