欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM BO 027-1-2001 RESISTANCE OF RIGID POLYMERS TO CRAZING.pdf

    • 资源ID:747327       资源大小:248.50KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM BO 027-1-2001 RESISTANCE OF RIGID POLYMERS TO CRAZING.pdf

    1、 FORD LABORATORY TEST METHOD BO 027-01 Date Action Revisions 2001 03 27 Revised Editorial no technical change A. Cockman 1992 07 28 Printed copies are uncontrolled Page 1 of 5 Copyright 2001, Ford Global Technologies, Inc. RESISTANCE OF RIGID POLYMERS TO CRAZING Application This procedure describes

    2、a method for determining the craze characteristics of rigid polymeric materials under stress. The method is applicable to molded test specimens or samples cut from fabricated parts. Equipment Required Test Rack See Figures 1 and 2. Weights See Figure 3. Weights are designed to stress test bars to lo

    3、ads of 1000 and 2000 psi. Burette One 500 mL per test bar. Test Stand and Burette Clamp To position burette over fulcrum point of test bar. Catch Basin Pan of suitable size to hold solution as it drips from test bars. Light Source “Dazor“ desk lamp or flashlight to place behind rack to observe craze

    4、 marks on test bar. Tape 1/2 inch pressure sensitive. Crazing Agents ESF-M5B2-A; ESF-M5B217-A; Aromatic hydrocarbons; halogenated hydrocarbons; ketones; organic or inorganic acids; aliphatic hydrocarbons. Conditioning and Test Conditions All test values indicated herein are based on material conditi

    5、oned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST METHOD BO 027-01 Page 2 of 5 Copyright 2001, Ford Global Technologies, Inc. Procedure 1. Prepar

    6、e four specimens 1/2 inch wide by 5 inches long by 1/8 inch thick for each load. These can be made either by the injection molding of bars or by sawing cast or extruded sheets. Specimens must be free of cracks, dirt, voids or feathered edges. Remove saw marks along the edges of the specimens by sand

    7、ing and buffing. 2. Suspend the required static load 1/8 inch from the end of the bar to provide a fiber stress of 1000 and 2000 psi. This must be done before the crazing agent is applied. Fasten the weight to the test bar, utilizing a small piece of tape over the wire weight holder. 3. Mount one en

    8、d of the specimen in the test rack of Figure 1 as shown in the detailed sketch of Section A-A. The fulcrum must be exactly 2 3/4 inches from the stationary end. 4. Check the samples immediately upon application of the load, check again after a few minutes and then allow to stand for two hours. For t

    9、he remainder of the test use the maximum load that does not produce crazing in the untreated specimens. If crazing occurs at 1000 psi, a smaller load should be used to calculate either a new weight or new fulcrum distance for this load utilizing the equation. Calculation of Fiber Stress S = Fiber St

    10、ress (psi) W = Applied Load (lbs.) L = Distance of load from fulcrum (inches) B = Width of specimen (inches) T = Thickness S = 6WL Bt 2 The load required to obtain a given stress is: W = SBt2 6L 5. Repeat Steps 1 to 3, positioning the burette so that the crazing agent will be applied to the fulcrum

    11、area. Do this prior to Step 3. Place the catch basin beneath the test bars. 6. Adjust the burette stopcock to apply the crazing agent at a rate of 10 20 drops per minute. 7. Check samples immediately upon application of the crazing agent, again after a few seconds, and at five minute intervals up to

    12、 30 minutes. If crazing does not occur within this time, inspect the specimens every 30 minutes for two hours. If crazing does not occur within this time, the test should be discontinued. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each p

    13、arty is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BO 027-01 Page 3 of 5 Copyright 2001, Ford Global Technologies, Inc. RESISTANCE OF RIGID POLYMERS TO CRAZING Craze Resistance Test Rack Figure 1 FORD LABORATORY TEST METHOD BO 027-01 Page 4 of

    14、5 Copyright 2001, Ford Global Technologies, Inc. RESISTANCE OF RIGID POLYMERS TO CRAZING Craze Resistance Test Rack - Details - Figure 2 FORD LABORATORY TEST METHOD BO 027-01 Page 5 of 5 Copyright 2001, Ford Global Technologies, Inc. RESISTANCE OF RIGID POLYMERS TO CRAZING Weights for Craze Test Figure 3


    注意事项

    本文(FORD FLTM BO 027-1-2001 RESISTANCE OF RIGID POLYMERS TO CRAZING.pdf)为本站会员(boatfragile160)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开