欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM BO 007-01-2000 SOFTENING POINT OF RESINS - BAR-BRUSH METHOD《条刷法测定树脂的软化点》.pdf

    • 资源ID:747304       资源大小:40.48KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM BO 007-01-2000 SOFTENING POINT OF RESINS - BAR-BRUSH METHOD《条刷法测定树脂的软化点》.pdf

    1、 FORD LABORATORY TEST METHOD BO 007-01 Date Action Revisions 2000 11 09 Revised Editorial no technical change A. Cockman 1992 07 13 Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. SOFTENING POINT OF RESINS - BAR-BRUSH METHOD Application This procedure is us

    2、ed to determine the softening point of resins used in the shell molding process. Apparatus Required Dennis Parr Melting Point Apparatus This apparatus, shown in the attached sketch, consists of a silver plated copper bar 1 inch square and 17 inches long. A temperature gradient is established along t

    3、he entire length of the bar by means of a cartridge type electric heater in an aluminum block and an adjustable thermoregulator. The operating range of the instrument is 0 - 482 F. A sliding contact copper Constantan thermocouple is connected to a calibrated potentiometer to indicate the temperature

    4、 at any point on the bar. Shown in the illustration but not supplied with the ap paratus is a brush - holding fixture which bridges the thermal gradient bar and enables the operator to brush the resin from the bar with a uniform pressure. Also shown is a hopper with a U.S. Standard #80 mesh screen a

    5、cross the bottom. The hopper is used to distribute the resin uniformly over the thermal gradient bar. The hopper has the following approximate dimensions: Bottom - 1 1/16 inches wide x 10 inches long; top - 5 inches wide x 14 inches long; height - 5 1/2 inches; screen - approximately 1 inch from the

    6、 lowest part of the hopper. Both the brush fixture and hopper must be fabricated as these items are not manufactured. Source: Central Scientific Co. Melting Point Apparatus - Catalog No. 23111 Potentiometer - Catalog No. 23114 Brush A soft, ca mel hair brush 1/4 inch in diameter and cut flat across

    7、the bottom is used for dusting the unattached resin from the thermal gradient bar. The brush is inserted in the brush fixture as shown so that the end of the brush is 1/8 inch below the heated bar. Stop Watch A stop watch or timing device is required. FORD LABORATORY TEST METHOD BO 007-01 Page 2 of

    8、3 Copyright 2000, For d Global Technologies, Inc. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h p rior to testing and tested under the same conditi

    9、ons unless otherwise specified. Procedure 1. Regulate the temperature of the thermal gradient bar to cover the softening point range (203 - 221 F for M4R34 resin) of the resin to be tested and allow to c ome to equilibrium. 2. Place the hopper over the thermal gradient bar so that it covers the soft

    10、ening point range of the resin under test. Pour a sample of the resin over the screen in the hopper, wipe across the screen twice with the end of a spatula to dislodge an even coating of resin on the bar, remove the hopper and start the stop watch. 3. At the end of one minute, begin brushing the res

    11、in from the bar, starting at the cool end. Move the brush fixture along the length of the bar while brushing twi ce over each area covered by the width of the brush. The sliding brushing action should be done as uniformly and rapidly as possible until that point on the bar is reached where the resin

    12、 adheres. 4. Move the sliding contact thermocouple to the point where the resin sticks to the thermal gradient bar and read the temperature on the potentiometer. This temperature is reported as the softening point of the resin. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BO 007-01 Page 3 of 3 Copyright 2000, For d Global Technologies, Inc. MELTING POINT APPARATUS (Dennis Parr)


    注意事项

    本文(FORD FLTM BO 007-01-2000 SOFTENING POINT OF RESINS - BAR-BRUSH METHOD《条刷法测定树脂的软化点》.pdf)为本站会员(刘芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开