欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD FLTM BL 104-01-2001 ALUMINUM CYLINDER HEAD HEAT-TRANSFER CORROSION TEST (Replaces FLTM BL 004-01)《铝气缸盖传热腐蚀试验 替代FLTM BL 004-01》.pdf

    • 资源ID:747148       资源大小:267.43KB        全文页数:8页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD FLTM BL 104-01-2001 ALUMINUM CYLINDER HEAD HEAT-TRANSFER CORROSION TEST (Replaces FLTM BL 004-01)《铝气缸盖传热腐蚀试验 替代FLTM BL 004-01》.pdf

    1、FORD LABORATORY TEST METHOD BL 104-01 2001 0822 ALUMINUM CYLINDER HEAD HEAT-TRANSFER CORROSION TEST Revised Editorial - no technical change A. Cockman Application It is essential that engine coolants prevent internal heat-transfer corrosion of aluminum cylinder heads during engine operation. Any cor

    2、rosion products formed will likely deposit on the nterior radiator surfaces, reducing the heat transfer efficiency of the radiator, or actually cause tube blockage. Over-heating and boil- over of the cooling system may then occur. This short-term screening test is used to evaluate the effectiveness

    3、of inhibited engine coolants in preventing high temperature heat-transfer corrosion of aluminum cylinder heads. Apparatus Required Temperatu re Controller Athena, Model 2000B-16 F/C or equivalent, with temperature control range up to 150 OC. Use type ” J ” thermocouple . Band Heaters Hotwatt, 950 wa

    4、tt standard construction band heaters or equivalent, 50 mm ID, 125 mm length, 120 volts AC, standard tightening clamp, type ”L” terminal. Ultrasonic Cleaner Bransonic Model 12, 1 quart, 50 watts, or equivalent. Vacuum Oven Thelco Model IO, to 150 OC, or equivalent. Vacuum Pump Ace-Nelson Model 91 1,

    5、 or equivalent. Heat-Transfer Corrosion Cell 1. Glass -ring cell, pyrex, 53 cm long (see Figure 1). 2. O-rings, Viton. (Teflon is not suitable due to high creep rate at test temperature.) I Date I Action I Revisions I CopyrightO2001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BL 104-0

    6、1 3. Heat-transfer bar, steel (see Figure 2). 4. Top and bottom assembly plates, 316 stainless steel (see Figure 3). 5. Pressure gauge, O - 150 kPa 6. Threaded rods, 72 cm length, typically 114 - 20 UNC. 7. Heat-transfer test sample, casting alloy of interest (see Figure 2). Analyt ical Balan ce 160

    7、 g minimum capacity with a precision of +/- 0.1 mg; Mettler Model No. H33AR. Curtis Matheson Catalog No. 368-522 or equivalent. Glass Capillary Pipet 150 mL Curtis Matheson Catalog No. 081 -91 9 or equivalent. Low Power Microscope Bausch and Lomb Model Z-3OLZ; Curtis Matheson Catalog No. 369-959 or

    8、equivalent. Apparatus Required Soft Bristle Brush Thin Cotton Gloves Carborundum Paper Various grits (60-600). Distilled or Deionized Water 1 O ppm maximum dissolved solids per ASTM DI 888. Sodium Chloride (NaC1) Reagent Grade. Acetone Reagent Grade. Caution: Low flash point. Chromium Trioxide (Cr03

    9、) Reagent Grade. Caution: Corrosive. Refer to Note (1) Chromic Acid Cleaning Solution Refer to Para 2 of this FLTM under cleaning of Aluminum Test Specimens. Caution: Corrosive. Refer to Note (1). Page 2 of 8 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BL 104-01 Conditio

    10、ning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 OC and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure Preparation of Coo

    11、lant Mixtures Prepare 1 liter of 25 % solution, sufficient for duplicate tests. Mix 250 mL of the coolant concentrate in 750 mL of distilled or deionized water. To this 1 liter mixture add 165 mg of sodium chloride (NaCI), either as the salt or as an aliquot from a previously prepared standard sodiu

    12、m chloride solution. This will give 100 ppm of chloride ions in the final mixture. Analyze for inhibitor concentration and specific gravity. Preparation of Aluminum Test Specimen The following steps are necessary in the preparation of the aluminum test specimen for maximum accuracy and reproducibili

    13、ty. The test samples may be reused. 1. Flat polish test samples with carborundum paper to remove any gross surface defects of previous corrosion damage. The final surface polish is with 600 grit paper. 2. Wash test sample with warm tap water, then rinse with distilled or deionized water, and finally

    14、 with acetone. Make sure thermocouple holes are free of metal chips and polishing debris. Flush holes well with acetone, and remove excess liquid. A glass capillary pipet is suitable for this purpose. 3. Dry test specimen in a vacuum oven for several hours at 65 - 90 OC. Since most castings have som

    15、e porosity this procedure is necessary to ensure removal of any residual liquid. From this point, test specimen should not be handled with bare hands in order to avoid weighing errors. Thin cotton gloves, Kodak or equivalent, are suitable for handling. 4. Cool specimen to 23 +/- 2 OC, weigh on an an

    16、alytical balance to 0.1 mg. 5. Assemble test specimen into test cell, avoiding mechanical damage. Test Cell Operation 1. Assemble cell according to Figure 1. New Viton Orings should be used between the aluminum test specimen and glass cell for each test. During assembly make sure -rings are properly

    17、 seated and avoid overtightening threaded rod nuts. Page 3 of 8 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BL 104-01 2. Fill cell with 500 mL of test coolant, place plug in fill hole, pressurize to 150 kPa and turn on band heater. 3. Adjust temperature to 135 +/- 2 OC w

    18、ith temperature controller. Temperature at auxiliary thermocouple hole should be monitored occasionally with a precision potentiometer. Cell is operated continuously at this temperature for 168 hours. 4. At end of test, turn off heater and allow test cell to cool to 23 +/-2 OC before disassembly. Re

    19、tain coolant solution for analysis (inhibitor concentration and specific gravity). After disassembly, glass cell should be cleaned with a large bristle brush, detergent and water. If deposits are not removed with this procedure, glass cell should be immersed in chromic acid cleaning solution until c

    20、lean. Cleaning of Aluminum Test Specimens 1. Wash specimen with a soft bristle brush using a mild detergent. 2. Immerse specimen in a small dish or beaker containing the following cleaning solution for 50 minutes at 80 OC: 475 mL distilled or deionized water 25 mL concentrated phosphoric acid 1 O g

    21、Cr03 (chromium trioxide) Occasionally brush the surface with a soft bristle brush. At the end of 5 minutes, transfer the beaker containing the aluminum test specimen and cleaning solution to an ultrasonic cleaning unit, and apply power for 1 minute. 3. Remove test specimen from cleaning solution, fl

    22、ush well with tap water, followed with distilled or deionized water, and finally acetone. Make sure thermocouple holes are flushed well and excess liquid is removed. Inspect surface using low power microscope. If any deposits remain, repeat steps 2 and 3. 4. Dry in vacuum oven using the same procedu

    23、re and precautions as outlined in the Preparation of Aluminum Test Specimens, Step 3. 5. Cool to 23 +/- 2 OC and weigh. Calculation of Corrosion Rate 1. Before the corrosion rate can be calculated, it is necessary to include a “blank“ correction. The “blank“ is the weight loss due to the chromic aci

    24、d and ultrasonic cleaning (Steps 1 - 5 of Cleaning of Aluminum Test Specimens), and should be added to the weight of the test specimen after the heat-flux test. Several specimens should be used to determine this “blank“ value, using the mean value. Page 4 of 8 Copynght02001, Ford Global Technologies

    25、, Inc FORD LABORATORY TEST METHOD BL 104-01 2. Calculate the corrosion rate with the following formula: Corrosion Rate = Wh - (W, + BI A Wb = weight of test specimen before heat-flux test W, = weight of test specimen after heat-flux test B = weight loss of “blank“ A = heat-flux surface area (inside

    26、O-ring) 3. A typical calculation is shown below: Wb = 105.1064 W, = 104.9196 B = 0.0013 A = 20.42 cm2 Corrosion Rate = 105.1 064 - (1 04.91 96 + 0.001 3) 20.42 = 0.0091 g/cm2 = 9.1 mg/cm2 Since the test was run for 1 week, the final corrosion rate is: 9.1 mg/cm2 /week Chemicals, materials, parts, an

    27、d equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Page 5 of 8 Copynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BL 104-01 ALUMINUM CYLINDER HEAD HEAT-TRANSFER CORROSIO

    28、N TEST ASSEMBLY 7 PRESSURE GAUGE TOP ASSEMBLY PLATE THREADED ROD, 114 x 20 TEST COOLANT LEVEL, 500 ML #40 PYREX O-RING CELL, 53 CM LENGTH THERMOCOUPLE HOLE VITON O-RING ALUMINUM TEST SPECIMEN /- STEEL HEAT TRANSFER BAR : BOTTOM ASSEMBLY PLATE /-950 WATT BAND HEATER fl II III Figure 1 Page 6 of 8 Cop

    29、ynght02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BL 104-01 ALUMINUM CYLINDER HEAT-TRANSFER CORROSION TEST ASSEMBLY Thermocouple Hole Drill to Fit I _ .-o.-o- Auxilliary thermocouple Hole Aluminum Electrode 12 Heat Transfer Bar (steel) Figure 2 Page 7 of 8 Copynght02001, Ford Glo

    30、bal Technologies, Inc FORD LABORATORY TEST METHOD BL 104-01 ALUMINUM CYLINDER HEAD-TRANSFER CORROSION TEST ASSEMBLY TOP ASY PLATE 1/8 PIPE - 2 HOLES - 1 6- f - - / 15.9 2 / / 7.9 DIA - 52.4 DIA - BOTTOM ASY PLATE ; 4 “-“-f 31.8 41.3 _.-._ i .- f 114.3 SQUARE Figure 3 Page 8 of 8 Copynght02001, Ford Global Technologies, Inc


    注意事项

    本文(FORD FLTM BL 104-01-2001 ALUMINUM CYLINDER HEAD HEAT-TRANSFER CORROSION TEST (Replaces FLTM BL 004-01)《铝气缸盖传热腐蚀试验 替代FLTM BL 004-01》.pdf)为本站会员(unhappyhay135)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开