1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 11 17 N-STATUS No known use. No replacement named D. DiGregorio, NA 2004 03 02 Revised Para 3.0 inserted; paras 3.11 and 4 deleted 1964 11 09 Released RO2-518 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC P
2、age 1 of 2 SOLVENT AND PENETRATING FLUID ESR-M99C56-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a liquid or aerosol propelled solvent containing graphite. 2. APPLICATION This specification was released originally for material used as a manifold heat valve l
3、ubricant and penetrating fluid. 3. REQUIREMENTS (Propellant free ingredients) 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 COMPOSITION 3.1.1 Volatiles (24 h a
4、t 105 C) 3.1.1.1 Water (KFR Method), max 2.0% 3.1.1.2 Petroleum Distillate, max 80% 3.1.2 Non-Volatiles (24 h at 105 C) 3.1.2.1 Tricresyl Phosphate, min 10% 3.1.2.2 Graphite, min 0.4% 3.1.2.3 Fat, min 7.0% 3.2 SPECIFIC GRAVITY 0.840 - 0.850 (ASTM D 1298) 3.3 VISCOSITY AT 37.8 C (GRAPHITE FREE) 1.83
5、- 4.26 cSt (mm2/s) (ASTM D 445) 3.4 FLASH POINT, min 52 C (ASTM D 92) 3.5 FIRE POINT, min 52 C (ASTM D 92) 3.6 ASH AT 983 C, max 1.0% ENGINEERING MATERIAL SPECIFICATIONESR-M99C56-A Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 2 3.7 PENETRATION Time Climb Di
6、stance minutes mm, minimum 0.5 3.2 3.0 6.4 20.0 9.6 60.0 13.0 Test Method: Place a bastard cut file (3/4 in (19 mm) wide) vertically in a watch glass, 100 mm in diameter, containing 5 ml of solvent and penetrating fluid and determine rate of climb. 3.8 CORROSION RESISTANCE (HUMIDITY) 200 h (FLTM BJ
7、107-03) No rust 3.9 SURFACE TENSION 27.0 - 28.0 dynes/cm (ASTM D 1331) 3.10 LABEL Provisions of this specification are applicable when material is used according to labeling directions. Any precautions involved in the use of the material must be clearly stated on the product label. The label(s) for
8、the material(s) must comply to the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission and all other applicable federal, state and local regulations. Supplier shall furnish the affected product engineering office with the label(s). Supplier shall fu
9、rnish certification that the composition of his product has been examined and that the label recommended is in compliance with the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission. Completed Material Health and Safety Data Sheets and Hazardous Su
10、bstances Data Sheets must be submitted by the supplier to the Ford Motor Company toxicologist. If applicable, supplier shall furnish a copy of the laboratory report wherein the product was evaluated under the procedures required by the Federal Hazardous Substances Act. If the label submitted by the supplier contains any advertising claims, suitable corroborative testing data must also be furnished. Such claims and data are encouraged.
