欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESK-M4G297-A-2011 SEALER PVC PRIMER OVEN CURING PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯底漆炉内固化可涂装的密封层 与福特WSS-M99P1111-A 一起使用》.pdf

    • 资源ID:746448       资源大小:61.15KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESK-M4G297-A-2011 SEALER PVC PRIMER OVEN CURING PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯底漆炉内固化可涂装的密封层 与福特WSS-M99P1111-A 一起使用》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Release No. Revision Rev. 2 2011 07 13 Revised Odor Requirements added W. Janitschke, EU 1993 02 01 EP00E10258804000 Revised A 3.9, released A2, A3, A4 W.Scholz 1987-12-18 SM/EQ1579 TP Release Controlled document at www.MATS Copyright 2011, Ford Global Techno

    2、logies, LLC Page 1 of 6 SEALER, PVC, PRIMER OVEN CURING, PAINTABLE ESK-M4G297-A SEALER, PVC, PRIMER OVEN CURING, PAINTABLE ESK-M4G297-A2 SEALER, PVC, PRIMER OVEN CURING, PAINTABLE ESK-M4G297-A3 SEALER, PVC, PRIMER OVEN CURING, PAINTABLE ESK-M4G297-A4 1. SCOPE The material defined by this specificati

    3、on is a solvent release, heat curing, stone peck resistant PVC sealer for exterior body areas. 2. APPLICATION This specification was release originally for material used as a stone peck protective coating for wheel house lip. The material is applied by a foam roller or airless spray on baked electro

    4、coat in a wet film thickness of approx. 160 - 320 micrometer wet on wet with spray primer. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 TEST P

    5、ANEL PREPARATION Use 300 x 100 x 0.8 - 0.9 mm E-coated test panels according to FLTM BI 120-01. The sealer must be applied on the cured E-coated test panel within 30 minutes after oven curing. 3.3 COLOR grey 3.4 SOLIDS 97.0 min (FLTM BV 150-10) 3.5 ASH 28.0 max (FLTM BV 150-10) 3.6 FLASH POINT 100 C

    6、 min (ASTM D 93, Method A) Note: In case testing at higher temperatures is not feasible because of gelling of test material, the supplier must certify in writing that each separate volatile ingredient has a flash point above 100 C. ENGINEERING MATERIAL SPECIFICATION ESK-M4G297-A/A2/A3/A4 Copyright 2

    7、011, Ford Global Technologies, LLC Page 2 of 6 3.7 DENSITY AT 20 C 1.29 g/cm3 max (ASTM D 1475) 3.8 VISCOSITY AT 20 C (Brookfield viscometer type RVT/D, No. 6 spindle) Test Method 1. Condition material under test to 20 C. 2. Stir material for 1 min by spatula. 3. Let the material rest for 30 min. 4.

    8、 Insert spindle into material and start measuring with undisturbed material at a frequency of 2.5/min; measuring time 3 min. 5. Continue measuring in the same way at frequencies of 5.0/min and 10.0/min. 3.8.1 As received, Pas +/- 10% A A2 A3 A4 at 2.5/min 25.0 60.0 100.0 130.0 at 5.0/min 19.0 40.0 6

    9、0.0 80.0 at 10.0/min 15.0 30.0 40.0 5.0 3.8.2 After Aging, Pas +/- 20 % (120 h at 35 +/- 2 C) at 2,5/min 33.0 75.0 140.0 220.0 at 5,0/min 26.0 55.0 85.0 130.0 at 10,0/min 21.0 40.0 65.0 100.0 3.9 SURFACE CONDITION AFTER AGING The material shall be dry to the touch after cooling to 23 +/- 2 C. It sha

    10、ll be free from cracks or bubbles and shall show a uniform closed paint film without staining or discolouration. After bending 90 deg around a mandrel of 100 mm dia. within 2 s (see FLTM BV 153-4) there shall be no evidence of chipping or loss of adhesion between the various layers. Test Method 1. T

    11、est panels per para 3.2., shall be coated with the material under test in such a manner (template 30 mm wide) that after curing a dry coating thickness of 150 - 300 micrometer is obtained. 2. After 10 min at 23 +/- 2 C, coat specimens wet on wet with production epoxy spray primer, to a dry film thic

    12、kness of 25 - 35 micrometer. 3. After 10 min at 23 +/- 2 C, cure specimens separately according to FLTM BV 150-5, for each applicable region: a) Min. Curing Cycle b) Max. Curing Cycle. 4. After 10 min at 23 +/- 2 C, spray separate specimens with light colored standard and metallic top coat enamel to

    13、 a coating thickness of 30 - 40 micrometer. 5. After 10 min at 23 +/- 2 C, cure specimens separately according to FLTM BV 150-5, for each applicable region: a) Min. Curing Cycle b) Max. Curing Cycle.ENGINEERING MATERIAL SPECIFICATION ESK-M4G297-A/A2/A3/A4 Copyright 2011, Ford Global Technologies, LL

    14、C Page 3 of 6 6. Condition for 2 h at 23 +/- 2 C and expose in mechanical convection oven maintained at 80 +/- 2 C for 120 h. 7. Test and examine after 24 h at 23 +/- 2 C. 3.10 FLEXIBILITY AFTER AGING No cracking, no (FLTM BV 153-2, Method C, except test chipping or loss of panels per 3.2., dry coat

    15、ing thickness adhesion 160 - 300 micrometer, curing cycle table 2, 2 h at 23 +/- 2 C, mandrel dia. 100 mm) 3.11 ADHESION AFTER HEAT AGING No cracking, no (FLTM BV 153-3, Method B, except test chipping or loss of panels per 3.2., dry coat thickness 160 - 300 micrometer adhesion 14 d aging at 80 +/- 2

    16、 C, 2 h at 23 +/- 2 C, mandrel dia. 100 mm) 3.12 ADHESION The material at all ranges of coating thickness must not be peeled-off in a coherent film. Test Method 1. Coat test panels from para 3.2. so that after the: (a) min curing cycle, (b) max curing cycle according to FLTM BV 150-5, T for each app

    17、licable region, a dry coating thickness of 0.5 mm beginning at one edge of the test panel and tapering to zero at the other is obtained. 2. After 24 h at 23 +/- 2 C make two cuts through the coating along the 300 mm length of the test panel and 20 mm apart and try to peel-off coating starting at the

    18、 edge with the lowest film thickness. 3.13 ABRASION RESISTANCE There shall be no exposed metal area showing after a) 100 Liter b) 250 Liter gravel impact. No loss of adhesion on and around the area of stone impact. Test Method 1. Test panels (para 3.2.) shall be coated with the material under test i

    19、n such a manner (template or foam roller) that after curing a dry coating thickness of 1) 160 - 200, b) 300 - 350 micrometre is obtained. 2. After 10 min at 23 +/- 2 C cure test specimens separately, according to FLTM BV 150-5, for each applicable region: a) min. curing cycle. b) max. curing cycle.

    20、3. Condition for 2 h at 23 +/- 2 C and expose in mechanical convection oven maintained at 70 +/- 2 C for 120 hours. 4. After conditioning for 24 h at 23 +/- 2 C determine the abrasion resistance according to ASTM D 968, except I.D. of tube 25 mm and at a gravel throughput rate of 30 - 40 Litres/h. F

    21、or each specimen a 5 Litres volume of fresh gravel shall be used. 5. Check for abrasion resistance and loss of adhesion after a) 100 Litre (dry coating thickness of 160 - 200 micrometer) b) 250 Litre (dry coating thickness of 300 - 350 micrometer) ENGINEERING MATERIAL SPECIFICATION ESK-M4G297-A/A2/A

    22、3/A4 Copyright 2011, Ford Global Technologies, LLC Page 4 of 6 gravel impact. Continue abrasion test until exposure of metal area and again check for loss of adhesion. Gravel: Type “GABBRO“ grain size 5-8 mm Supply Source: ODENWALDER HARTSTEIN INDUSTRIE GMBH Erbacher Str. 62 D - 6101 Rossdorf 3.14 C

    23、ORROSION RESISTANCE The material shall protect the test panel from corrosion for a salt spray exposure period of 500 hours. It shall show no expansion, flaking or loss of abrasion resistance. No loss of adhesion on and around the area of stone impact. Test Method 1. Prepare test specimens in accorda

    24、nce with para 3.13, sections 1-3. 2. After conditioning for 24 hours at 23 +/- 2 C expose specimens for 500 hours to a salt spray fog according to ASTM B 117. 3. After conditioning for 72 h at 23 +/- 2 C determine abrasion resistance as specified under para 3.13 and examine test panels for evidence

    25、of corrosion. Disregard the area 5 mm from the edges. 3.15 FLOW RATE 2 mm max (FLTM BV 153-1, Method A, except test panel per para 3.2., wet film thickness 280-300 micrometer, template 30 mm width, 270 mm length of sealer bead, 30 min at 120 +/- 2 C). 3.16 COMPATIBILITY WITH PRODUCTION PAINTS No tac

    26、kiness of material surface, no cracking or blistering. The paint shall cover the sealer satisfactorily without evidence of discolouration or staining. 3.16.1 Wetability and Staining Test Method 1. Specimens preparation according to clause 3.13, test method, section 1, test material width 30-35 mm. 2

    27、. Proceed as outlined under FLTM BV 153-8, Method A, section 2-6, except use lightest and darkest solid colour and metallic basecoat/clearcoat. 3. After 72 h at 23 +/- 2 C mask one half of the sealer ribbon and expose for 240 h in the Fluorescent Sunlamp Cabinet (FLTM EU-BU 52-2). ENGINEERING MATERI

    28、AL SPECIFICATION ESK-M4G297-A/A2/A3/A4 Copyright 2011, Ford Global Technologies, LLC Page 5 of 6 3.16.2 Determination of Discoloration after Aging None Test Method 1. Specimens preparation according to 3.16.1, section 1 and 2. 2. After 24 h at 23 +/- 2 C store separate assemblies in the darkness for

    29、 240 h at 40 +/- 2 C in a mechanical convection oven. 3.16.3 Determination of Yellowing None (FLTM BV 153-12) 3.16.4 Resistance to Weathering No discoloration Test Method 1. Specimens preparation according to 3.16.1, section 1 and 2. 2. Expose test specimens in the Miami/Florida area for 6 months an

    30、d 1 year at 5 deg to the south. 3. Prior to examination clean specimens using soap and water. 3.17 TEMPERATURE CYCLING TEST No chipping, no flaking, no loss of Test Method adhesion 1. Specimens preparation according to clause 3.16.1, test method, section 1 and 2. 2. After conditioning 72 h at 23 +/-

    31、 2C expose specimens three times to the following cycle. 3 h at 80 +/- 2 C 1 h at 23 +/- 2 C 3 h at -40 +/- 1 C 1 h at 23 +/- 2 C 16 h at 38 +/- 2 C and 98 +/- 2 % RH 3. After 24 h at 23 +/- 2 C bend 90 deg around a mandrel of 100 mm dia. within 2 s (FLTM BV 153-4). 3.18 ABRASIVES The material shall

    32、 contain no abrasive agents. Test Method Dilute a one gram sample of material under test with three gram toluene and mix thoroughly. Rub a portion of the diluted material approx. 10 times between two pieces of flat, clean plate glass. The appearance of scratches on the glass plates shall be consider

    33、ed failure. 3.19 SPRAYABILITY The material shall be a smooth homogeneous mixture, free from foreign material and suitable for use in airless spray equipment. It shall spray evenly and rapidly with no tip clogging or fluctuations in the spray pattern and with a minimum spray back and fogging. ENGINEE

    34、RING MATERIAL SPECIFICATION ESK-M4G297-A/A2/A3/A4 Copyright 2011, Ford Global Technologies, LLC Page 6 of 6 3.20 QUALITY The material shall be of uniform quality, free from foreign material and properties detrimental to normal production use. 3.21 ODOR Rating 3 max (FLTM BO 131-03, cured material pe

    35、r min cycle as in FLTM BV 150-05, for the individual region, for interior application only) 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Speci

    36、fications. 4.1 STORAGE STABILITY (from date of receipt at Ford Motor Company) The material must be stable for 3 month, when stored in sealed unopened drums out of direct sunlight at ambient temperatures between 5 C and 32 C. 5. SUMMARY OF REVISIONS 2011 07 13 Added Odor Requirement. Editorial changes for clarification.


    注意事项

    本文(FORD ESK-M4G297-A-2011 SEALER PVC PRIMER OVEN CURING PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《聚氯乙烯底漆炉内固化可涂装的密封层 与福特WSS-M99P1111-A 一起使用》.pdf)为本站会员(王申宇)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开