欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESB-M4D382-A-2009 LAMINATE VINYL - METAL - EXTERIOR GRADE TO BE USED WITH FORD WSS-M99P1111-A 《室外级乙烯基-金属层压板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    • 资源ID:745536       资源大小:31.07KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESB-M4D382-A-2009 LAMINATE VINYL - METAL - EXTERIOR GRADE TO BE USED WITH FORD WSS-M99P1111-A 《室外级乙烯基-金属层压板 与标准FORD WSS-M99P1111-A一起使用 》.pdf

    1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 11 19 N-STATUS No replacement named J. Crist, Na 2005 05 26 Revised Inserted 3.0; Deleted 3.1, 3.9 & 4 1977 11 11 Released AH1-708 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 1 of 4 LAMINATE, VINYL -

    2、 METAL - EXTERIOR GRADE ESB-M4D382-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a polyvinyl chloride film laminated to a metal substrate which is suitable for post forming exterior parts. 2. APPLICATION This specification was released originally for material

    3、 used for the 1978 Mark V coach lamp bezel, with the vinyl film coordinated to match the vinyl roof. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A).

    4、3.2 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Body and Electrical Product Engineering master sample, or shall be as specified on the engineering drawing. In addition, there shall be no evidence of vinyl tear, delamination or drawback, particularly in the cri

    5、tical radius areas after forming. 3.3 DESIGN LIMITATIONS The vinyl metal laminate defined in this specification is intended for use in part designs employing bends with outside radii that are recommended to be not less than 0.120 in (3.05 mm). Bends of greater severity may cause failure of the vinyl

    6、 along the bent edge. For each design, laminates subject to this specification shall be evaluated simulating the most severe proposed application condition. 3.4 METAL BACKING The metal originally released for this application is SAE 51434 type stainless steel. Other types of metals, such as aluminum

    7、, may be employed provided they offer corrosion resistance and performance equivalent to the specified SAE 51434 steel. The type, quality and finish of the metal backing selected must be specified on the engineering drawing. 3.5 VINYL FILM (Test conducted on vinyl film only) ENGINEERING MATERIAL SPE

    8、CIFICATIONESB-M4D382-APrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 4 3.5.1 General This film shall have the necessary flexibility and elongation characteristics to allow it to be easily formed in the drawing operation without delamination, tearing, drawback

    9、 (creepage), loss of embossing, color change or cracking. The original properties of the vinyl film shall not be adversely affected after lamination or forming. The vinyl film shall be ESB-M2F133-A exterior vinyl roof quality, and is generally used, for this specification, without fabric backing. 3.

    10、5.2 Mildew (FLTM BN 012-03) After the test the samples shall show no less than 1 mm zone of inhibition and there shall be no evidence of pink staining. 3.5.3 Soiling, max 15% (FLTM BN 112-01) Cleanability, based on manual rubbing with Nainsook cloth and/or a soft bristle brush, using liquid detergen

    11、t, shall be equal to the approved master sample. 3.5.4 H2S Staining No discoloration (FLTM AN 102-01) 3.6 THICKNESS AND DIMENSIONS The thickness of the vinyl film, metal substrate and total thickness of the laminate shall be specified on the engineering drawings along with other part dimensions. 3.7

    12、 FLAT LAMINATE - PRIOR TO FORMING 3.7.1 Drawability The flat laminate shall bend 180 around a 1/8 in (3.2 mm) mandrel without damage to the vinyl film or delamination of the vinyl-metal bond. In addition, the decorative vinyl surface shall exhibit no hazing, blushing, crazing, cracking or clouding a

    13、nd shall be equivalent to the originally evaluated and approved master sample (on file in the BEPE Textile Engineering Section). 3.7.2 Resistance to Elevated Temperature The vinyl film shall exhibit no flattening or loss of embossing, print or ink pattern loss (washout), vinyl creepage or drawback g

    14、reater than that exhibited by the original, approved master sample on file in the BEPE Textile Engineering Section. Additionally, the vinyl film shall not stain, exhibit color tone change or change in hue in excess of rating 4-5 of the AATCC Gray Scale for evaluating change in color (10 step). Test

    15、Method: Place a 4 x 4 in (100 x 100 mm) flat test specimen or a formed part of the vinyl-metal construction in a convection oven maintained at 121 +/- 3 C for a period of 30 min (vinyl surface up). For parts such as vinyl roof moldings, that are covered with heat protection pads during paint repair

    16、oven exposure, place the specimen or part in a convection oven maintained at 88 +/- 3 C for a period of 30 min. Allow to cool to room temperature and visually examine and compare with the original exposed, approved master sample. ENGINEERING MATERIAL SPECIFICATIONESB-M4D382-APrinted copies are uncon

    17、trolled Copyright 2009, Ford Global Technologies, LLC Page 3 of 4 3.7.3 Scuff Resistance (FLTM BN 108-04, 500 cycles, 2 lb (0.91 kg), “A“ head) The vinyl surface shall show no evidence of breakthrough. 3.7.4 Abrasion Resistance (FLTM BN 108-02, 1000 cycles, 1000 g load) The vinyl coating shall show

    18、no evidence of wearthrough and the entire vinyl film shall possess a uniform and compatible coating. 3.8 FORMED PART 3.8.1 Peel Adhesion (ASTM D 413, Machine Method, 1 in (25 mm) wide strip specimen) The adhesion between the vinyl film and the metal substrate, when conducted on flat surfaces as well

    19、 as on highly contoured surfaces and edges, shall be as follows: Original (as received): Laminate must not separate without at least a 50% cohesive failure of the vinyl. 3.8.2 Dimensional Stability The formed part shall show no evidence of flattening or loss of embossing, print or ink pattern loss (

    20、washout), loss of grain, blistering, shrinkage or expansion to the extent of causing unsightly wrinkles. The part shall exhibit no visible delamination, pullouts, creepage or cracking that will result in an objectionable appearance and/or exposure of the metal substrate. Test Method: Place other ass

    21、embly in a mechanical convection oven maintained at 83 +/- 3 C for 7 days. Allow the specimens to cool to room temperature and examine. 3.8.3 Thermal Shock Resistance (FLTM BI 107-05) Direct the steam blast at the smallest radii of both concave and convex surfaces, formed edges and on the crosshatch

    22、. The formed laminate shall show no evidence of degradation, loss of adhesion or delamination. 3.8.4 Impact, Gardner At Room Temperature 10 in lb (1.1 J) At -29 C 5 in lb (0.6 J) The vinyl film shall show no evidence of cracking, crazing, blushing or delamination. Test Method: The parts shall be imp

    23、acted on the decorative surface, 1/4 in (6.4 mm) away from any formed edge, using a Gardner Model IG-1120 (or equivalent) tester with a 1/2 in (12.7 mm) diameter hemispherical impact head. The parts shall also be impacted on both convex and concave decorative surface areas. The low temperature test

    24、shall be conducted after exposure for a 4 h minimum at -29 +/- 1 C and impacted within 20 s after removal from the low temperature chamber. 3.8.5 Weathering Resistance The vinyl coating shall not stain, craze, blush, haze, crack, exhibit color tone change or change in hue, in excess of rating 4-5 of

    25、 the AATCC Gray Scale for evaluating change in color (10 step), when exposed as follows: ENGINEERING MATERIAL SPECIFICATIONESB-M4D382-APrinted copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 4 of 4 Fadeometer 1600 h (SAE J 1885) Weatherometer 1600 h (FLTM BO 101-01) Florid

    26、a Exposure 160,000 langleys (45 South DWI) Arizona Exposure 160,000 langleys (45 South DWI) 3.8.6 Environmental Aging After exposure to the following cycle, the part shall exhibit no visible vinyl delamination, pullouts, creepage, shrinkage, cracking or scuffing on any surface that will affect the a

    27、ppearance when installed. Cycle consists of the following sequence*: 2 h exposure in the steam autoclave, 88 - 93 C 1 h exposure at -29 C 1 h exposure at 88 C * Note: Prior to exposure, trace the original position of the outer edges of the vinyl on the metal flange end to provide a gage for subseque

    28、nt movement or creepage of the decorative vinyl. 3.8.7 Resistance to Gasoline and Hydrocarbons After soaking separate samples in: Hydrocarbon fluid (2.1% toluene, 0.5% diisobutylene, 97.4% octane primary reference fuel) Any regular grade of commercially available non-leaded gasoline Leaded gasoline

    29、The material surface shall not exhibit any color change, loss of gloss, dulling, tackiness or spotting. In addition, the vinyl-metal laminate shall exhibit no evidence of delamination, shrinkage or cracking. Test Method: Soak each 2 x 8 in (50 x 200 mm) sample in a beaker containing approximately 16

    30、 fluid ounces (473 ml) of hydrocarbon fluid or gasoline for 1 h. Remove sample, dry at standard conditions for 3 h and observe. 3.8.8 Salt Spray Exposure (ASTM B 117, 240 h) The parts shall exhibit no evidence of color change, chalking, wrinkling, crazing, milkiness or loss of embossment greater tha

    31、n that exhibited by the approved master sample on file in the BEPE Textile Engineering Section. In addition, the vinyl-metal laminate shall not delaminate, crack, corrode excessively or exhibit any other characteristics which would produce an objectionable appearance when the part is in the installed position.


    注意事项

    本文(FORD ESB-M4D382-A-2009 LAMINATE VINYL - METAL - EXTERIOR GRADE TO BE USED WITH FORD WSS-M99P1111-A 《室外级乙烯基-金属层压板 与标准FORD WSS-M99P1111-A一起使用 》.pdf)为本站会员(bonesoil321)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开