欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESB-M4D300-A-2008 ABS MOLDING COMPOUND HIGH IMPACT - HIGH TEMPERATURE TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯模塑料 耐冲击 耐高温(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSB-M4D69.pdf

    • 资源ID:745507       资源大小:44.25KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESB-M4D300-A-2008 ABS MOLDING COMPOUND HIGH IMPACT - HIGH TEMPERATURE TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯模塑料 耐冲击 耐高温(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSB-M4D69.pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Ver. 4 2008 07 29 N-STATUS Replaced by WSB-M4D690-A C. Boese, FNA 2005 01 27 Revised Removed Inactive ESB-M4D300-B Inserted 3.0; Deleted 3.1, 3.6 & 4 1969 04 18 Released ESB-M4D330-A AY1-808 Printed copies are uncontrolled Copyright 2008, For

    2、d Global Technologies, LLC Page 1 of 2 ABS MOLDING COMPOUND, HIGH IMPACT - HIGH TEMPERATURE ESB-M4D300-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is an acrylonitrile butadiene styrene (ABS) injection molding compound. The material is supplied in natural or co

    3、lor pigmented form, intended only for interior applications, which require a high impact resistance. 2. APPLICATION This specification was released originally for material used for interior automotive body parts, such as “A“ pillar moldings and vent grilles. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS

    4、 FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 MOLDED MATERIAL (Natural and pigmented injection molded samples) 3.2.1 Specific Gravity 1.01 - 1.22 (ASTM D 792) 3.2.2 Tensile Strength at

    5、 Break, min 5,500 psi (38 MPa) (ASTM D 638) 3.2.3 Flexural Yield Strength, min 8,000 psi (55 MPa) (ASTM D 790, 1/8 x 1 x 4 in (3.2 x 25 x 100 mm) sample) 3.2.4 Impact Strength, Gardner, in-lb (J), min Natural Pigmented At 23 +/- 2 C 120 (13.6) 100 (11.3) At -29 +/- 1 C 12 (1.36) 8 (0.9) Test Method:

    6、 Condition a Gardner impact tester (Model IG-1115) with a 4 lb (1.8 kg), 1/2 in (12.7 mm) diameter steel impact head, a 1/2 in (12.7 mm) diameter steel baseplate) and several 4 x 4 x 0.100 +/- 0.005 in (100 x 100 x 2.54 +/- 0.13 mm) injection molded plaques in a low temperature chamber operated at -

    7、29 +/- 1 C for 5 h. Remove the impact tester and place on a concrete floor or any minimal energy absorbing surface. Impact the samples within 5 s after removal from cold box. Room temperature tests are to be conducted with the same equipment. No sample shall show any indication of cracking. ENGINEER

    8、ING MATERIAL SPECIFICATION ESB-M4D300-A Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 2 of 2 3.2.5 Deflection Temperature, min (ASTM D 648, 264 psi (1820 kPa), 1/2 in (12.7 mm) sample width) As Received 93 C Conditioned 2 h at 93 C 102 C 3.2.6 Hardness - Rockwell

    9、 “R“, min 95 (ASTM D 785) 3.3 MOLDED PART 3.3.1 Color Natural or as specified on engineering drawing 3.3.2 Physical Properties Specific requirements for physical properties of molded parts, where required, shall be specified on the engineering drawing. 3.3.3 Heat Resistance Finished parts must pass

    10、the following test: Test Method: Condition typically assembled parts in car position for 3 h at 102 +/- 3 C (or as specified on engineering drawing). After removal, parts shall show no more than 0.5% shrinkage, nor shall there be local shrinkage where the part has been gated which will interfere wit

    11、h assembly to mating parts or affect its appearance. The part shall not warp to an extent that would affect its use in ultimate assembly. 3.3.4 Resistance to Fade (SAE J1885) The material shall fade no more than the master sample approved for production on file in the Quality Control of Test Laborat

    12、ory after 120 SFH. 3.3.5 Odor The intensity and character of the material odor shall not be objectionable or offensive. 3.4 FLAMMABILITY, max 4 in (101 mm)/min (FLTM BN 024-02, without the lot sampling plan) In addition, the test specimen shall not exhibit any flashing or sudden flaming on either su

    13、rface in excess of the above max value. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 IMPACT STRENGTH, Izod, min (ASTM D 256, 1/8 x 1/2 x 2-1/2 in (3.2 x 12.7 x 64 mm) bar, 0.010 in (0.25 mm) notch) 5.1.1 Natural 5.0 ft lb/in (267 J/m) 5.1.2 Pigmented 4.0 ft lb/in (214 J/m) 5.2 COEFFICIENT OF LINEAR THERMAL EXPANSION 5.0 - 5.4 x 10-5/ F (ASTM D 696) (9.0 - 9.7 x 10-5/ C)


    注意事项

    本文(FORD ESB-M4D300-A-2008 ABS MOLDING COMPOUND HIGH IMPACT - HIGH TEMPERATURE TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯模塑料 耐冲击 耐高温(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSB-M4D69.pdf)为本站会员(inwarn120)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开