欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    FORD ESB-M2J103-B-2012 ENAMEL BLACK BAKING UNDERBODY TO BE USED WITH FORD WSS-M99P1111-A .pdf

    • 资源ID:745319       资源大小:49.10KB        全文页数:4页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    FORD ESB-M2J103-B-2012 ENAMEL BLACK BAKING UNDERBODY TO BE USED WITH FORD WSS-M99P1111-A .pdf

    1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 05 04 N Status No usage or replacement N. Benipal, NA 2008 01 16 Revised Updated Format, No Technical Change 1969 04 29 Released AY1-815 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of 4 ENA

    2、MEL, BLACK BAKING, UNDERBODY ESB-M2J103-B NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a low or high bake black underbody baking enamel. 2. APPLICATION This specification was released originally for enamels used on automotive underbodies and other non-visible

    3、surfaces. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 COMPOSITION 3.1.1 Non-Volatile, min 42.0% (FLTM BI 102-01) 3.1.1.1 Pigment The pigments

    4、 shall be balanced and blended so that the finished enamel matches the Ford Motor Company master panel in color and luster and meets the requirements of this specification for durability. 3.1.1.2 Vehicle The vehicle shall consist primarily of alkyd resins. There shall be no hard gums present. 3.1.2

    5、Volatile The volatile components shall be such that a dry film of at least 0.00075 in (19 m) can be applied in two spray coats with satisfactory appearance. 3.1.3 Toxicity The enamel shall contain no benzol (benzene), chlorinated or other toxic compounds, or hydrolyzable chlorine derivatives nor hav

    6、e an obnoxious or objectionable odor. ENGINEERING MATERIAL SPECIFICATION ESB-M2J103-B Copyright 2012, Ford Global Technologies, LLC Page 2 of 4 3.1.4 Compatibility with Obsolete or Surplus Stock (FLTM BI 002-04) Material shall be compatible with additions of the following: . ESB-M2J200-AA and BA Int

    7、erior Enamel. . ESB-M16J102-B Primer. . ESB-M6J103-B Primer. . ESB-M6J62-A Reclaim Primer. . ESB-M6J80-A Electrostatic Primer. . ESB-M30J100-A Enamels. . ESB-M32J100-A Enamels. Additionally, the material shall be able to accept up to 50 percent total addition of any of the above surplus and still me

    8、et the resistance, application, and stability requirements of this specification. 3.2 PHYSICAL PROPERTIES 3.2.1 Viscosity 20 - 28 s (FLTM BI 111-01) 3.2.2 Stability The material shall not jell nor liver upon standing. Test Method: Place a sealed, 3/4 full, pt (0.5 l) can in an oven for 16 h at 60 +/

    9、- 1 C. An appreciable increase in viscosity (approximately 15 s) shall indicate nonstability. 3.3 PREPARATION OF TEST PANELS 3.3.1 Adhesion Panel Using panels zinc phosphated per ESB-M3P1, spray ESB-M6J102 (0.00075 in (19 m) min dry film thickness, on lower half of panels and flash 1 - 2 min. Do not

    10、 bake. Spray ESB-M2J103 (0.00075 in (19 m) min dry film thickness) over the entire panel. Bake per paragraph 3.3.3. 3.3.2 Resistance Properties Panels Prepare panels as in 3.3.1, omitting ESB-M6J102 flash coat. 3.3.3 Bake The material shall meet all applicable requirements of this specification when

    11、 baked as follows: 15 min at 135 C 30 min at 163 C ENGINEERING MATERIAL SPECIFICATION ESB-M2J103-B Copyright 2012, Ford Global Technologies, LLC Page 3 of 4 3.4 APPEARANCE The material shall level satisfactorily on spray application. There shall be no sagging or roughness resulting from dry spray. 3

    12、.5 FILM PROPERTIES 3.5.1 Adhesion (FLTM BI 106-01) No chipping or flaking over the following substrates: . Phosphate coated steel (ESB-M3P1). . ESB-M6J102 Epoxy Primer (wet on wet). In addition, spray ESB-M32J100 Acrylic Enamel (0.0015 - 0.0020 in (39 - 50 m) dry film thickness) over unsanded ESB-M2

    13、J103 and bake 17 min at 129 C. Adhesion shall be satisfactory. 3.6 RESISTANCE PROPERTIES 3.6.1 Salt Spray Resistance, min 120 h (FLTM BI 103-01) No failure by blistering, rusting, or more than 1/8 in (3 mm) rust or blister creepage from a line scribed to bare metal when tested on panels prepared acc

    14、ording to para 3.3.2. 3.6.2 Water Immersion, min 120 h (FLTM BI 104-01) Any blistering, peeling or other film defects shall constitute failure. 3.7 BLEEDING The material shall not bleed. Test Method Apply casual overspray to the surface of a CRLC steel panel, phosphate coated per ESB-M3P1-A. Overspr

    15、ay should consist of separate specks of enamel. Allow to flash off and apply a solid covering coat of ESB-M30J100 quality white enamel to the overspray area. Bake according to paragraph 3.3.1. Age for 4 h under a S-1 sun lamp or fluorescent sun lamp as described in FLTM BU 105-01. Remove and inspect

    16、. Subject the panel to the sun lamp for 20 additional h and reinspect. Repeat the procedure using ESB-M32J100 quality white enamel. ENGINEERING MATERIAL SPECIFICATION ESB-M2J103-B Copyright 2012, Ford Global Technologies, LLC Page 4 of 4 5. GENERAL INFORMATION The information given below is provided

    17、 for clarification and assistance in meeting the requirements of this specification. 5.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing Engineering Department shall notify both the Plant Security and the Safety Units of its presence in the Plant to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notification.


    注意事项

    本文(FORD ESB-M2J103-B-2012 ENAMEL BLACK BAKING UNDERBODY TO BE USED WITH FORD WSS-M99P1111-A .pdf)为本站会员(花仙子)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开