1、BRITISH STANDARD Specification for Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) Part 2-1. Applicability of the general rules to RCCBs functionally independent of line voltage The European Standard EN 610082-1 : 1994 with th
2、e incorporation of amendment All : 1998 has the status of a British Standard ICs 29.120.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGW LAW BS EN 61008-2-1 1995 IrnpliTnenting Amendment No. 1 not pu blbhed separady _ - STD-BSI BS EN bLOO-2-L-ENGL 1995 m IbZlibb7 0733342 LBO Amd.
3、 No. Date 10273 November 1998 BS EN 61008-2-1 : 1995 Issue 2, Noveiiiber 1998 Text affected Addition to 9.23 Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees
4、 of the following countries: Austria Belgium Denmark Finland Fiance Germany Greece Iceland Ireland IMY Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom This British Standard, haing been prepued under the direction of the Elecrrotechnical sector Bwd, ww pubhhed under the
5、 authority of the sunduds Board and comes into effect on 10 Mirch 1QB5 0 BSI 1998 The following BSi references relate to the work on this standard: Committee reference PEU23 Mt for comment W22488 DC IGBN O 68 29S9 9 STD-BSI BS EN bLOO8-2-L-ENGL 1775 W Lb2LibbS 07333i3 017 hue 1, November 1998 BS EN
6、61008-2-1 : 1995 2 3 4 5 6 Inside back cover 1 Back cover Summary of pages The following table identifies the current issue of each page. Issue 1 indicates that a page has been introduced for the first time by amendment. Subsequent issue numbers indicate an updated page. Page Front cover Inside fron
7、t cover a b 1 11 EN title page 2 2 1 blank 2 blank 2 Issue 2 2 removed removed 2 original original * * ZT) O BSI 1998 a STD*BSI BS EN b1008-2-1-ENGL I775 1b24Lb7 O733144 T53 Issue 2, November 1998 BS EN 61008-2-1 : 1996 Contents page cooperating organizations inside front cover National foreword i F
8、breword 2 kt Of EN 61008-2-1 3 Nationai appendix NA (informative) Conunittees responsible inside back cover National foreword This British Standard has been prepared under the direction of the Electro- amendment All was approved by CENELEC on 199804-01. CENELEC nienibers are bound to coniply with th
9、e CENXENELEC intemai Regulations which stipuiate the conitions for giving this European Standard the status of a national standard without any alteration Uptedate lists and bibliographica references concerning such national standards may be obtained on application to the Centrai Secretariat or to an
10、y CENELEC member. This European Standard exists in three officiai versions (Engish, French, Gennan). A version in any other ianguage made by translation under the responsibility of a CENELEC member into its own language and notified to the Centrai Secretariat has the same status as the officiai vers
11、ions. CENELEC members are the national electrotechnid committees of Austria, Belgium, Denmark, Fnand, -ce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netheriands, Norway, pbrtugai, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electromcai Standarization Com
12、it Europen de Normalisation Electrotechnique Europisches Komitee fr Elektmtechnkhe Normung Central Secretariat: me de Stassart Sa, B-10M) Bmesele O 1994 Copyright reserved to CENELEC members Ref. No. EN 61008-2-1 : 1994 + All : 1998 E - STD.BS1 BS EN blJClC18-2-1-ENGL 1995 B 1b24bb 0733Llib 82b Page
13、 2 Issue 2, November 1998 EN 61008-2-1 : 1994 I Foreword The text of the international Standard IEC 10082-1 : 1990, which makes reference to and finds application with lEC 1008-1 : 1990, was submitted to the Unique Acceptance procedure (UM) for acceptance as a European standard simuitaneously with t
14、he UAP on prEN 61-1. As the W on prEN 61008-1, for which common modifications had been prepared by lchnicai committee CENELEC TC 23E, Circuit-breakem and similar equipment for household and similar use, did not obtain a sufficient number of positive votes, neither document was accepted. On the basis
15、 of the common modifcations added in the revise prEN 61008-1, no changes to IEC 18-2-1 were necessary and the document was submitted to the formal vote. The new draft was approved by CENELEC as EN 61008-2-1 on 1994-03-08. The following dates were fixed: - latest date of publication of an identic81 n
16、ational - latest date of withdrawal of conficting national standard (dp) 1996-07-01 standards (dow) 2000-07-01 For products which have complied with the shown by the mufacturer or by a certification body, this previous standard may continue to apply for pipduction until 2005-07-01. conformity of pdu
17、cts with the requirements of this standard ensures conformity with the essential requhments of Directive 73/23/EEC (Low Voltage Directive) and its amendment 03/68/EEC. There are no special national conditions or A-deviations to this European Standard other than relwant national standard before 2000-
18、07-01, 85 th- listed in EN 61008-1 : 1994. Foreword to amendment All This amendment was prepared by the Technical Committee CENELEC TC BE, Circuit breakers and similar devices for household and similar applications. The text of the draft was submitted to he Unique Acceptance Procedm and was approved
19、 by CENELEC as amendment All to EN G1008-2-1 : 1994 on 1!3984-01. The following dates were nxed: - latest date by which the amendment has to be implemented at nationai level by publication of an identical national standard or by endorsement (dop) 19981141 - iatestdatebywhichthe natjonal standards co
20、nflictkg with the amendment have to be witlidrawn (dow) 200303-01 iib * * m STD-BSI BS EN bZ008-2-L-ENGL L79S m Lb24bb7 0733347 7b2 m hge 3 EN 61oOtb2-1: 1994 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBs) Part 2-1: Applicabi
21、lity of the general rules to RCCBs functionally independent of line voltage Introduction This Part 2-1 supplements or modifies the corresponding clauses 1008-1 to cover its applicability to RCCBs functionally independent voltage. in IEC of line 1. Scope This clause of Part 1 is applicable, except as
22、 follows: Replace the first paragraph by the following: This International Standard applies to RCCBs functionally independent of line voltage, for household and similar uses, not incorporating overcurrent protection, for rated voltages not exceeding 440 V a.c. and rated currents not exceeding 125 A,
23、 intended principally for protection against electric shock hazard, 2 Normative references This clause of Part 1 is applicable. 3 Definitions This clause of Part 1 is applicable except that definitions 3.3.5, 3.4.10, 3.4.10.1 and 3.4.10.2 do not apply. 4 Classification This clause of Part 1 is appli
24、cable except that 4.1.2 does not apply. 5 Characteristics of RCCBs This clause of Part 1 is applicable except that the last two lines of 5.1 do not apply. 6 This clause of Part 1 is applicable except that letter n) does not apply. Marking and other product information STD*BSI BS EN b1008-2-L-ENGL 17
25、75 1b24hL7 07331ifl bT7 me 4 EN 61ot321: 1994 Issue 2, November 1998 7 Standard conditions for operation in service and for installation This clause of Part 1 is applicable. 8 Requirements for construction and opsration This clause of Part 1 is applicable except that 8.12 does not apply. 9 Tests Thi
26、s clause of Part 1 is applicable except as follows. In table 7 of 9.1.1 the 15th dashed text (referred to the test of 9.17) does not apply. Note 3 of 9.7.4 does not apply. 9.9.5 does not apply. The last two paragraphs of letter a) and the last paragraph of letter i) of 9.11.2.1 do not apply. 9.17 da
27、s not apply. The last paragraphs of 9.18.1 and of 9.18.2 do not apply. 9.23 Add after the 1st paragraph: In case there are no electronic components connected between phase poles and/or between phase poles and the neutral pole, the RCCB is loaded with rated current at any convenient voltage. Figures
28、The figures of Part 1 are applicable. Annaxas The annexes of Part 1 are applicable except that, in table A.l of annex A, the words “9.17 - Behaviour in the case of failure of the line voltage“ (referid to test sequence 01) do not apply and that, in annex IS, the last two symbols do not apply. (B BSI
29、 1998 - STD*BSI BS EN b1008-2-L-mENGL 1975 W lb2ibb7 0733147 535 W BS EN 61008-2-1 : 1995 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Elect rotechnical Sector Board to Technical Committee PE
30、L123 upon which the following bodies were represented: ASTA Certification Services Association of Consulting Engineers Association of Control Manufacturers - TACMA (BEAMA Ltd.) British Lawnmower Manufacturers Federation Consumer Policy Committee of BSI Consumers Association Department of Trade and I
31、ndustry (Consumer Safety Unit) ERA Technology Ltd. Elect rical Installation Equipment Manufacturers Association (BEAMA Ltd. ) Electricity Association Federation of the Electronics Industry Instil ution of Electrical Engineers Instil ution of Mechanical Engineers National Inspection Council for Elect
32、rical Installation Contracting National Quality Assurance Portable Electric Tool Manufacturers Association BS EN 61008-2-1 : 1995 BSI 389 Chiswick High Road London w4 &u. Issue 2, November 1998 BSI - British Standards Institution BSI is the independent national body responsible for preparing Brit,is
33、h Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest, amendments or editions. It is t
34、he constant alln of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front c
35、over. Tel O181 996 9000. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed
36、to Customer Services. Tel: 0181 996 7000. Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of
37、 information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel 0181 996 7111. Fax:
38、0181 996 7048. Subscribing members of BSI are kept up to date wit,h standards developnients and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel O181 996 7002. Fax: O181 996 7001. Copyright Copyright subs
39、ists in all BSI publications. BSI also holds the copyright, in the IJK, o thr publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any forni or by a
40、ny means - electronic, photocopying, recording or otherwise - without prior written permission froni BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained froni the Copyright Manager. Tel 0181 996 7070.
