欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    EN 2899-2018 en Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with vulcanized rubbers.pdf

    • 资源ID:710427       资源大小:1.13MB        全文页数:12页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    EN 2899-2018 en Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with vulcanized rubbers.pdf

    1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with vulcanized rubbersBS EN 2899:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2899 M

    2、ay 2018 ICS 49.025.40 English Version Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with vulcanized rubbers Srie arospatiale - lastomres vulcaniss - Essais de sensibilit la corrosion en atmosphre humide des mtaux au contact

    3、des lastomres vulcaniss Luft- und Raumfahrt - Vulkanisierte Elastomere - Prfung der Korrosionsempfindlichkeit in Feuchtklima von Metallen bei Berhrung mit vulkanisierten Elastomeren This European Standard was approved by CEN on 17 December 2017. CEN members are bound to comply with the CEN/CENELEC I

    4、nternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

    5、any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

    6、 versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

    7、way, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All ri

    8、ghts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2899:2018 ENational forewordThis British Standard is the UK implementation of EN 2899:2018. The UK participation in its preparation was entrusted to Technical Committee ACE/65, Non-metallic mat

    9、erials for aerospace purposes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institutio

    10、n 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 51123 3ICS 49.025.40Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2018.Amendments/corrigen

    11、da issued since publicationDate Text affectedBRITISH STANDARDBS EN 2899:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2899 May 2018 ICS 49.025.40 English Version Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with

    12、vulcanized rubbers Srie arospatiale - lastomres vulcaniss - Essais de sensibilit la corrosion en atmosphre humide des mtaux au contact des lastomres vulcaniss Luft- und Raumfahrt - Vulkanisierte Elastomere - Prfung der Korrosionsempfindlichkeit in Feuchtklima von Metallen bei Berhrung mit vulkanisie

    13、rten Elastomeren This European Standard was approved by CEN on 17 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and b

    14、ibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the res

    15、ponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R

    16、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROP

    17、EN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2899:2018 EBS EN 2899:2018EN 2899:2018 (E) 2 Contents Page

    18、 European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus and auxiliary products 5 6 Specimens 5 7 Test conditions . 6 8 Procedure. 6 9 Interpretation of results . 7 10 Designation 7 11 Test report . 8 BS EN 2899:2018EN 2899:2018 (E) 3 European

    19、 foreword This document (EN 2899:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associa

    20、tions and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2018, and conflicting national standards

    21、shall be withdrawn at the latest by November 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations,

    22、 the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La

    23、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 2899:2018EN 2899:2018 (E) 4 1 Scope This document defines tests on the susceptibility to corrosion in a damp atmosphere of

    24、metals in contact with vulcanized rubbers. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest ed

    25、ition of the referenced document (including any amendments) applies. EN 2071, Aerospace series Sheets in aluminium and aluminium alloys Thickness 0,25 mm a 6 mm Dimensions EN 22171, Steel FE-PL52 S 1 080 MPa Rm 1 250 MPa Sheets and plates 2 mm a 20 mm Aerospace series 2EN 2395, Aerospace series Alum

    26、inium alloy AL-P2014A T4 or T42 Sheet and strip 0,4 mm a 6 mm EN 3525, Aerospace series Steel FE-PL1505 (15CrMoV6) Air melted Hardened and tempered Plate 6 mm a 20 mm 1 080 MPa Rm 1 280 MPa ISO 23529, Rubber General procedures for preparing and conditioning test pieces for physical test methods 3 Te

    27、rms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at

    28、 http:/www.iso.org/obp 3.1 contact corrosion the visually perceptible deterioration of the metal surface in contact with rubbers, after exposure in a damp atmosphere 4 Principle The rubber test pieces shall be directly placed after immersion in the test fluid between two test metal disks and exposed

    29、 to a damp atmosphere under defined conditions. After exposure, the metal disks shall be visually examined so that deterioration due to corrosion can be noted. 1Inactive for new design, see EN 3525. 2Published as ASD-STAN Standard at the date of publication of this European Standard by AeroSpace and

    30、 Defence industries Association of Europe - Standardization (ASD-STAN) (www.asd-stan.org). BS EN 2899:2018EN 2899:2018 (E) 5 5 Apparatus and auxiliary products 5.1 Apparatus test assembly which enables a compression of (12 3) % of the rubber test pieces by means of metal disks (Figure 1); a device f

    31、or producing x 20 magnification; climatic chamber where a relative humidity of 95 % minimum can be obtained at (23 2) C. 5.2 Auxiliary products polyethylene gloves; appropriate solvent; lint free cotton cloth; test fluids. 6 Specimens 6.1 Metal disks 6.1.1 Material Type 1 Aluminium alloy AL-P2014A T

    32、4 or T42 according to EN 2395. Type 2 Steel FE-PL52S 1 080 MPa Rm 1 250 MPa according to EN 2217. 6.1.2 Dimensions The metal to be tested shall be circular disks of an outer diameter (120 0,5) mm, with a (2000,2+) mm diameter hole in the centre (see Figure 1). These disks shall be 5 mm thick minimum

    33、 if they are in steel and 10 mm minimum thick if they are in aluminium so that they are not deformed when gripped. 6.1.3 Preparation The metal disks shall have a roughness of 0,4 m maximum on all surfaces. The edges shall be rounded. 6.1.4 Number For each test and exposure method, use two metal disk

    34、s. The two disks may be made of the same metal or of two different metals. 6.2 Rubber test pieces 6.2.1 Material According to the material standard. BS EN 2899:2018EN 2899:2018 (E) 6 6.2.2 Dimensions (20 1) mm x (20 1) mm cut from test strips (2 0,2) mm thick. 6.2.3 Number Three test pieces for each

    35、 test and exposure method. 6.2.4 Time lapse between vulcanization and testing The test pieces shall be stored according to ISO 23529. 7 Test conditions 7.1 Test temperature The temperature shall be (23 2) C. 7.2 Testing time The testing time shall be 7 d or a multiple of 7 d. 7.3 Humidity The relati

    36、ve humidity shall be 95 % minimum. 8 Procedure Clean all the surfaces of the metallic disks and the rubber test pieces with a lint free cotton cloth soaked in an appropriate solvent and leave to dry for 2 h minimum at (23 2) C. After cleaning, the degreased test pieces shall not be touched with bare

    37、 fingers; they shall only be handled with polyethylene gloves. Depending on the method chosen, the rubber test pieces and the metallic disks shall be conditioned as follows: Method A: The rubber test pieces and metallic disks shall be immersed in the test liquid for 15 min at a temperature of (23 2)

    38、 C, then allowed to drain. Method B: The rubber test pieces and metallic disks shall not undergo any conditioning. Next, place the rubber test pieces and the annular isolating block between the two metallic disks. The isolating block shall be chosen with a thickness such that the rubber test pieces

    39、are compressed by (12 3) %. Tighten the assembly until it comes to rest against the block. BS EN 2899:2018EN 2899:2018 (E) 7 Place the assembly in the test chamber in a damp atmosphere. NOTE The test pieces shall be placed at a distance of at least 10 mm from the edges of the metallic disks and arra

    40、nged symmetrically (Figure 1). At the end of exposure time, the test assembly shall be placed in a normal atmosphere for (30 5) min at (23 2) C. The metallic disks shall be separated from the rubber test pieces, then cleaned using appropriate solvents to eliminate all traces of rubber. The two metal

    41、lic disks shall be then subjected to a visual examination at x 20 magnification to detect any discolouration or sign of corrosion. 9 Interpretation of results Any discolouration or surface deterioration of the metal strip shall be described in the test report. 10 Designation EXAMPLE EN2899 A A Numbe

    42、r of this standard Type of material used for metallic disks (see Table 1) Method used (A or B) Table 1 Type Code 1 and 1 A 1 and 2 or 2 and 1 B 2 and 2 C BS EN 2899:2018EN 2899:2018 (E) 8 11 Test report The test report shall make reference to this standard and shall include the following information

    43、: test method (A or B); if test method A: Description of test liquid; type and designation of the tested product; batch and date of manufacture; material of metal disks; test environment; exposure time; number of tests; visible deteriorations of the metal disks/description of corrosion; any detail n

    44、ot provided for this standard of the subject of specific requirements; test date. BS EN 2899:2018EN 2899:2018 (E) 9 Dimensions in millimetres Key 1 Metal disks 2 Isolating flanged ring 3 Stainless steel screw M18 4 Test piece thickness: 2 5 Polyamide isolating block 6 Washer 7 Steel axis Figure 1 Ex

    45、ample of test assembly (metallic disks of the same material) BS EN 2899:2018This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards

    46、 and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embo

    47、died in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your org

    48、anization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, th

    49、rough our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or e


    注意事项

    本文(EN 2899-2018 en Aerospace series - Vulcanized rubbers - Test on the susceptibility to corrosion in a damp atmosphere of metals in contact with vulcanized rubbers.pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开