欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    EN 10249-2-1995 en Cold Formed Sheet Piling of Non Alloy Steels - Part 2 Tolerances on Shape and Dimensions《非合金钢冷成型板桩 第2部分 外形和尺寸公差》.pdf

    • 资源ID:705321       资源大小:430.73KB        全文页数:12页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    EN 10249-2-1995 en Cold Formed Sheet Piling of Non Alloy Steels - Part 2 Tolerances on Shape and Dimensions《非合金钢冷成型板桩 第2部分 外形和尺寸公差》.pdf

    1、Cold formed sheet piling of non alloy steels - Part 2. Tolerances on shape and dimensions The European Standard EN 10249-2 : 1995 has the status of a British Standard NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW I7 r .- BS EN 10249-2 : 1996 CEN EN*L0249-2 75 H 3404589 03207

    2、33 874 H under the authority of the Standards Board and comes into Amd. No. Date effect on 15 March 1996 0 BSI 1996 The following BSI references relate to the work on this standard: Committee reference ISEI12 Draft for comment 93/309095 DC ISBN O 580 24949 2 BS EN 10249-2 : 1996 Rxt affected Committ

    3、ees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/ 12, Structural steels, upon which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork Association Ltd. ritish Iron and Stccl Produccrs Associati

    4、on British Railways Board Department of Transport Institution of Structural Engineers Lloyds Register of Shipping National Association of Steel Stockholders Railway Industry Association Society of Motor Manufacturers and Traders Limited Steel Construction Institute Welding Institute CEN EN*10247-2 7

    5、5 m 3404589 0120732 700 m BS EN 10249-2 : 1996 Contents Page Committees responsible Inside front cover National foreword u Foreword 2 Text of EN 10249-2 3 CEN EN*30249-2 95 = 3404589 0320733 b47 BS EN 10249-2 : 1996 Nat ional foreword This British Standard has been prepared by Technical Committee IS

    6、E/12 and is the English language version of EN 10249-2 : 1995 Cold formed sheet piling of non alloy steels - Part 2: Iolerances on shape and dimensions, published by the European Committee for Standardization (CEN). Compliance with a British Standard does not of itself confer immunity from legal obl

    7、igations. 11 0 BSI 1996 CEN EN*110249-2 95 3404589 01120734 583 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10249-2 June 1995 ICs 77.140.70 Descriptors: iron and steel products, metal sections, sheet pilings, steels, unalloyed steels, dimensions, dimensional tolerances, form tolerances Engl

    8、ish version Cold formed sheet piling of non alloy steels - Part 2: Tolerances on shape and dimensions Palplanches profiles froid en aciers non allis - Sthlen - Partie 2: Tolrances sur forme et dimensions Kaltgeformte Spundbohlen aus unlegierte Teil 2: Grenzabmae und Formtoleranzen This European Stan

    9、dard was approved by CEN on 1995-05-05. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

    10、national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language an

    11、d notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United

    12、Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 01995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members.

    13、 Ref. No. EN 10249-2 : 1995 E CEN EN*10249-2 95 3404589 0320735 4LT Page 2 EN 10249-2 : 1995 Foreword This European Standard was prepared by SC4, Sheet piling, of Technical Committee ECISS/TClO, Structural steels - Qualities, the secretariat of which is held by NNI. EN 10249 is composed of two Parts

    14、: Part 1: Technical delivery conditions; Part 2: lblerances on shape and dimensions. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1995, and conflicting national standards shall be with

    15、drawn at the latest by December 1995. According to the CENICENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swed

    16、en, Switzerland, United Kingdom. Contents Foreword 1 Scope 2 Normative references 3 Control of tolerances - General 4 Height of profiles 5 Width of profiles 6 Wall thickness of profiles 7 Straightness of profiles 7.1 General 7.2 Bending 7.3 Curving 7.4 Twisting 8 Length 9 Squareness of ends 10 Angul

    17、ar deviation 11 Mass of profiles 12 Joints, overlapping 13 Options Page 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 6 6 6 O BSI 1996 CEN EN*10249-2 95 3404589 0320736 356 1 Scope This Part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed no

    18、n alloy steel sheet piles which are defined in EN 10249-1 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter

    19、. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10051 Continuously hot rolled uncoate

    20、d plate, sheet and strip of non alloy and alloy steels - Iblerances on dimensions and shape Cold formed sheet piling of non alloy steels Part 1: Tkchnical delivery conditions EN 10249-1 3 Control of tolerances - General 3.1 All the measurements are taken outside of the zone deformed by cutting at a

    21、distance from the ends of at least 250 mm. 3.2 The dimensions are measured by instruments of appropriate accuracy. 4 Height of profiles The tolerances on the height of sheet piles are given in table 1. 5 Width of profiles The tolerances on the width of profiles are as follows: - individual sheet pil

    22、e: I 2 % of the nominal width; - pair of interlocked sheet piles: f 3 % of the nominal width. 6 Wall thickness of profiles The tolerances on the wall thickness of the profiles shall comply with the requirements of table 2 of EN 10051, for a nominal width of strip and sheet over 1 800 mm. Page 3 EN 1

    23、0249-2 : 1995 7 Straightness of profiles 7.1 General The controls of the profile straightness (measurement of bow-heights corresponding to bending and curving) shall be carried out on a pile which freely lies on a plane surface according to the following figures 1 and 2. For Z-sheet piles, the contr

    24、ols are carried out on an interlocked pair of sheet piles, and if appropriate, on a welded pair of sheet piles when they are delivered welded. 7.2 Bending The bow-height S in the horizontal plane of the sheet pile is the distance between the cord and the arc formed by the sheet pile edge (see figure

    25、 1). The bow-height (S) shall be I 0,25 5% L. 7.3 Curving The bow-height C in the vertical (perpendicular) plane of the sheet pile is the distance between the sheet pile edge in its middle and the reference plane surface (see figure 2). The bow-height (C) shall be I 0,25 % L. 7.4 Twisting One sheet

    26、pile end being fixed, the dimension (V) which characterizes the twisting is measured at the free end of the sheet pile with regard to the reference plane (see figure 3). The dimension (V) shall not exceed 2 % L with a maximum of 100 mm. 8 Length The normal tolerance is f 50 mm. A reduced tolerance m

    27、ay be agreed at the time of the enquiry and order. Option 1, see 13.2. 9 Squareness of ends The total deviation between the highest and the lowest point of the cutting plane (t) shall not exceed 2 % of the width of the profile, measured perpendicular to the longitudinal axis. When the sheet piles ar

    28、e delivered in seamed pairs by means of welds all along the lock, the upper end shall not present a misalignment (t) exceeding 20 mm. O BSI 1996 CEN EN*10249-2 95 = 3404589 0320737 292 W Page 4 EN 10249-2 : 1995 I able 1. Tolerances on the height of sheet piled) I Dimensions in millimetres Designati

    29、on I Figure I Nominal dimension I Tolerance Height ln h I 200 200 h I 300 300 h I 400 400 h c h fJ f4 f6 f8 f 10 I Applicable to the different shapes of cold formed sheet piles, the figure shows a trench sheet. I Upper view Dimensions in mm. Figure 1. Measurement of bending O BSI 1996 CEN EN*L0247-2

    30、 75 m 34045137 01120738 1127 m Page 5 EN 10249-2 : 1995 Lateral view Figure 2. Measurement of curving AA Figure 3. Measurement of twisting O BSI 1996 CEN EN*l10249-2 95 m 3404589 Olt20739 Ob5 m I Page 6 EN 10249-2 : 1995 t - I I- Figure 4. Squareness of ends b-4 Smaller leg Figure 5. Flange angle a

    31、10 Angular deviation For special applications, the tolerance2) on the flange angle a (see figure 5) may be agreed at the time of the enquiry and order. Option 2, See 13.3 11 Mass of profiles Compared with the calculated mass (product of ordered pile length by mass per linear metre of pile according

    32、to section tables of the producers), the actual mass may show a deviation of not more than Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Info

    33、rmation on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick: T

    34、el: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick: Tel: 0181 996 7002; Fax:

    35、O181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sys

    36、tem or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.

    37、If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL. ISBN O 580 24949 2


    注意事项

    本文(EN 10249-2-1995 en Cold Formed Sheet Piling of Non Alloy Steels - Part 2 Tolerances on Shape and Dimensions《非合金钢冷成型板桩 第2部分 外形和尺寸公差》.pdf)为本站会员(wealthynice100)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开