1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change in accordance with the notice of revision 5962-R354-97. - jak 97-06-27 Monica L. Poelking B Change in accordance with the notice of revision 5962-R453-97. - cfs 97-09-03 Monica L. Poelking C Redrawn with changes. Update the boilerplate to
2、current requirements as specified in MIL-PRF-38535. - jak 08-11-05 Thomas M. Hess REV SHET REV C C C C SHEET 15 16 17 18 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Bernard J. Miesse STANDARD MICROCIRCUIT DRAWING CHECKED BY Charles
3、 F. Saffle Jr. DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-09-09 MICROCIRCUIT, DIGITAL, ADVANCED HIGH-SPEED CMOS,
4、 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-96865 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E033-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
5、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)
6、and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following ex
7、ample: 5962 - 96865 01 Q R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535
8、specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) ident
9、ify the circuit function as follows: Device type Generic number Circuit function 01 54AHCT374 Octal edge-triggered D-type flip-flop with three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
10、 follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case
11、 outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in
12、 MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISI
13、ON LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to +7.0 V dc 4/ DC input clamp current (IIK) (VINVCC) . 20 mA DC outpu
14、t clamp current (IOK) (VOUTVCC) 20 mA Continuous output current (IO) (VOUT= 0 V to VCC) . 25 mA Continuous current through VCCor GND 75 mA Storage temperature range (TSTG) -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Juncti
15、on temperature (TJ) . +175C Maximum power dissipation at TA= +55C (instill air) (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH. 2.0 V Maximum low level input voltage (VIL). 0.8 V Input voltage ran
16、ge (VIN) . +0.0 V dc to VCCOutput voltage range (VOUT) +0.0 V dc to VCCMaximum high level output current (IOH) . -8 mA Maximum low level output current (IOL) . +8 mA Minimum input rise or fall rate (t/V). 20 ns/V Case operating temperature range (TC) -55C to +125C 1/ Stresses above the absolute maxi
17、mum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange
18、and case temperature range of -55C to +125C. Unused inputs must be held high or low to prevent them from floating. 4/ The input and output voltage ratings may be exceeded providing that the input and output current ratings are observed. 5/ Unused inputs must be held high or low to prevent them from
19、floating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government s
20、pecification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL
21、-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcir
22、cuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the even
23、t of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individ
24、ual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual
25、item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein
26、 for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be
27、 as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and
28、 test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3
29、.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrica
30、l test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packa
31、ges where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance wi
32、th MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as re
33、quired in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of complianc
34、e shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, fo
35、r device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PR
36、F-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that
37、affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option o
38、f the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 38 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M
39、ICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwis
40、e specified VCCGroup A subgroups Limits 3/ Unit Min Max IOH= -50 A 1, 2, 3 4.4 1 3.94 High level output voltage 3006 VOHFor all inputs affecting outputs under test, VIN= 2.0 V or 0.8 V For all other inputs, VIN= VCCor GND IOH= -8 mA 4.5 V 2, 3 3.8 V IOH= 50 A 1, 2, 3 0.1 1 0.36 Low level output volt
41、age 3007 VOLFor all inputs affecting outputs under test, VIN= 2.0 V or 0.8 V For all other inputs, VIN= VCCor GND IOH= 8 mA 4.5 V 2, 3 0.44 V 1 +0.25 Three-state output leakage current, high 3021 IOZHOE = 2.0 V For all other inputs, VIN= VCCor GND VOUT= VCC5.5 V 2, 3 +2.5 A 1 -0.25 Three-state outpu
42、t leakage current, low 3020 IOZLOE = 2.0 V For all other inputs, VIN= VCCor GND VOUT= GND 5.5 V 2, 3 -2.5 A 1 +0.1 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND 5.5 V 2, 3 +1.0 A 1 -0.1 Input current low 3009 IILFor input under test, VIN= GND For all o
43、ther inputs, VIN= VCCor GND 5.5 V 2, 3 -1.0 A 1 4.0 Quiescent supply current, 3005 ICCFor all inputs, VIN= VCCor GND IOUT= 0 A 5.5 V 2, 3 40 A 1 1.35 Quiescent supply current delta, TTL input levels 3005 ICC4/ One input at 3.4 V Other inputs VCCor GND 5.5 V 2, 3 1.5 mA Input capacitance 3012 CINTC=
44、+25C VIN= VCCor GND See 4.4.1c 5.0 V 4 10.0 pF Output capacitance 3012 COUTTC= +25C VOUT= VCCor GND See 4.4.1c 5.0 V 4 10.0 pF Power dissipation capacitance CPD5/ TC= +25C f = 1 MHz See 4.4.1c 5.0 V 4 35.0 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking p
45、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test con
46、ditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max VOLP6/ 5.0 V 4 1400 Low level ground bounce noise VOLV6/ 5.0 V 4 -1250 mV VOHP6/ 5.0 V 4 400 High level VCCbounce noise VOHV6/ VIH= 3.0 V, VIL= 0.0 V TA= +25C See 4.4.1d See figure 4 5.0
47、 V 4 -1100 mV 4.5 V Functional tests 3014 7/ VIH= 2.0 V, VIL= 0.0 V Verify output VOSee 4.4.1b 5.5 V 7, 8 L H Pulse duration, CLK high or low twCL= 50 pF minimum See figure 5 4.5 V and 5.5 V 9, 10, 11 6.5 ns Setup time, data high or low before CLK tsCL= 50 pF minimum See figure 5 4.5 V and 5.5 V 9,
48、10, 11 2.5 ns Hold time, data high or low after CLK thCL= 50 pF minimum See figure 5 4.5 V and 5.5 V 2.5 ns 9 90 CL= 15 pF minimum See figure 5 8/ 4.5 V and 5.5 V 10, 11 80 9 85 Maximum clock frequency fMAXCL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 75 MHz See footnotes on next sheet. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96865 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C
