1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Redrawn with changes. Made corrections to the pinout of case outline X. Added a sentence to paragraphs 4.2 and 4.3. Editorial changes throughout. 93-04-30 K. A. Cottongim B Changes in accordance with NOR 5962-R068-94. 93-12-10 K. A. Cottongim C A
2、dded a class K device. Redrew entire document. -sld 98-04-09 K. A. Cottongim D Update drawing to the current requirements of MIL-PRF-38534. 05-07-21 Raymond Monnin REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Steve Duncan
3、DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones POST OFFICE BOX 3990 COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Gregory Lude MICROCIRCUIT, HYBRID, DIGITAL, OPTICAL COUPLED FILTER AND AGENC
4、IES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 92-07-07 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-91676 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E391-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
5、 SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are
6、available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 91676 01 H X X Federal RHA Device Device Case Lead stock class designator
7、 type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA desig
8、nator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 66079, 66079-300 Single channel, optocoupler 1.2.3 Device class designator. This device class designator shall be a single l
9、etter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documenta
10、tion K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality
11、class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are base
12、d upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect syste
13、m performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
14、T DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure
15、1 7 Co-axial Y See figure 1 7 Bolthead co-axial 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) +7.0 V dc (1 minute maximum) Input current. 20 mA Storage temperature range -65C to +150C Power dissipation (TC= +125
16、C) . 175 mW Lead temperature (soldering, 10 seconds). +260C Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc High level input current 12.5 mA minimum 2/ Low level input current. 250 A dc maximum Normalized fanout (TTL load) 6 max
17、imum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these d
18、ocuments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component
19、Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Docu
20、ment Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable la
21、ws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ This condition permits at least 20 percent hF(CTR) de
22、gradation. This initial switching threshold is 10 mA dc or less. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FO
23、RM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer
24、s Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modifi
25、cation in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case out
26、line(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Switching test circuit and waveforms. The switching test circuit and waveforms shall be as specified on figure 3. 3.3 Electrical performance ch
27、aracteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I
28、I. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In
29、 addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should
30、 include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certific
31、ate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A
32、 certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Qu
33、ality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBU
34、S COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions -55C TC +125C 4.5 V dc VCC 5.5 V dc unless otherwise specified Group A subgroups Device type Min Max Unit Low level output voltage VOLVCC= 5.5 V,
35、IF= 10 mA, IOL= 10 mA 1/ 1,2,3 01 0.6 V High level output current IOHVCC= 5.5 V, VO= 5.5 V, IF= 250 mA 1,2,3 01 250 A High level supply current ICCHVCC= 5.5 V, IF= 0 mA 1,2,3 01 20 mA Low level supply current ICCLVCC= 5.5 V, IF= 20 mA 1,2,3 01 30 mA 1,2 1.75 Input forward voltage VFIF= 20 mA 3 01 1.
36、85 V Input reverse breakdown voltage VBRIR= 10 A 1,2,3 01 5 V Input to output insulation leakage current 2/ IIOVIO= 1000 V dc, t = 5 sec, relative humidity = 45%, TC= +25C 1 01 1.0 A Input to output capacitance 3/ 6/ CIOf = 1 MHz, TC= +25C 1 01 3.0 pF Input to case isolation leakage current IICVIC=
37、500 V, pins 1 and 2 shorted together, TC= +25C 1 01 1.0 A Output to case isolation leakage current IOCVIC= 500 V, pins 4, 5, and 6 shorted together, TC= +25C 1 01 1.0 A Input to case capacitance CICf = 1 MHz, TC= +25C 4 01 5.0 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reprodu
38、ction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Condition
39、s -55C TC +125C 4.5 V dc VCC 5.5 V dc unless otherwise specified Group A subgroups Device type Min Max Unit 9 100 Propagation delay time, low to high output level 4/ tPLHR1 = 510, CL= 15 pF, IF= 13 mA 10,11 01 140 ns 9 100 Propagation delay time, high to low output level 5/ tPHLR1 = 510, CL= 15 pF,
40、IF= 13 mA 10,11 01 140 ns Common mode transient immunity at output high level 6/ | CMH | VCM- 10 Vp-p, IF= 0 mA, VO= 2 V min, R1 = 510 9,10,11 01 1000 V/s Common mode transient immunity at output low level 6/ | CML | VCM- 10 Vp-p, IF= 10 mA, VO= 0.8 V min, R1 = 510 9,10,11 01 1000 V/s 1/ It is essen
41、tial that a ceramic bypass capacitor of .01 F be connected from VCCto ground. 2/ Device considered a two-terminal device, pins 1 through 3 are shorted together and pins 4 through7 are shorted together. 3/ Measured between each input pair shorted together and all outputs shorted together. 4/ The tPLH
42、propagation delay is measured from the 6.5 mA point on the trailing edge of the input pulse to the 1.5 V point on the trailing edge of the output pulse. 5/ The tPHLpropagation delay is measured from the 6.5 mA point on the trailing edge of the input pulse to the 1.5 V point on the trailing edge of t
43、he output pulse. 6/ Parameters shall be tested as part of device initial characterization and after design and process changes. Parameters shall be guaranteed to the limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted
44、 without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Inches mm .005 .127 .008 .203 .012 .305 .016 .406 .019 .483 .070 1.778 .100 2.540 .137 3.480 .167 4.24
45、2 .209 5.308 .212 5.384 .500 12.700 .535 13.590 .560 14.224 .562 14.275 NOTES: 1. Dimensions are in inches: 2. Metric equivalents are for general information only. 3. Measured at base of the header. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted witho
46、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Inches mm .005 .127 .010 .254 .015 .381 .016 .406 .019 .483 .062 1.575 .070 1.778 .100 2.540 .200 5.080 .209
47、 5.309 .212 5.385 .215 5.461 .223 5.664 .225 5.715 .232 5.893 .233 5.918 .243 6.172 .250 6.350 .270 6.858 .312 7.925 .500 12.700 .560 14.224 NOTES: 1. Dimensions are in inches: 2. Metric equivalents are for general information only. 3. Measured at base of the header. FIGURE 1. Case outline(s) - Cont
48、inued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91676 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outlines X and Y Terminal numbers Terminal symbols 1 Anode 2 Cathode 3 No connection 4 VCC5 VOUT6 Ground 7 No connection FIGURE 2. Termin
