1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Made change to paragraph 1.2.4. Corrected figure 3, timing waveform. Editorial changes throughout. 92-03-10 A. Barone B Figure 1 case outline X, correct “.170 min pin length” to “.220 min pin length”. Update drawing to current requirements. 07-03
2、-20 Joseph Rodenbeck C Table I: For Total current test, symbols ICC1-SB, ICC1-25, ICC1-50, and ICC1-100for device types 05 and 06. Change max value from 25 mA to 60 mA. gc 07-05-02 Robert M. Heber The original first sheet of this drawing has been replaced. REV SHEET REV C C C C C SHEET 15 16 17 18 1
3、9 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Donald R. Osborne DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR
4、USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, DIGITAL, MIL-STD-1553, SINGLE CHANNEL, 12 VOLT DRIVER-RECEIVER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-02-06 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-90829 SHEET 1 OF 19 DSCC FORM 2233
5、 APR 97 5962-E354-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This draw
6、ing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in th
7、e PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90829 01 H X X _ Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardne
8、ss assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Coupling transformer
9、turns ratio Device type Generic number Circuit function Transformer Direct Single channel driver-receiver 01 FC155371 (receiver idle normally low) 1.66:1 1.2:1 02 FC155372 (receiver idle normally high) 1.66:1 1.2:1 03 ARX3420 (receiver idle normally low) 1.41:1 1:1 04 ARX3424 (receiver idle normally
10、 high) 1.41:1 1:1 05 NHI-1531 (receiver idle normally low) 1.77:1 1.25:1 06 NHI-1545 (receiver idle normally high) 1.77:1 1.25:1 07 CT1589M (receiver idle normally low) 1.2:1 1:1 08 CT1589I (receiver idle normally high) 1.2:1 1:1 1.2.3 Device class designator. This device class designator shall be a
11、 single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance
12、documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military
13、 quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). Provided by IHSNot for Resa
14、leNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 E Designates devices which are based upon one of the other classes (K, H, or
15、G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified qu
16、ality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style
17、T See figure 1 24 Flat package U See figure 1 24 Dual-in-line package X See figure 1 24 Dual-in-line package Y See figure 1 24 Dual-in-line package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage range: VCC-0.3 V dc to +18 V
18、dc VEE(device types 01, 02, 03, 04, 07, and 08) +0.3 V dc to -18 V dc VCC1. -0.3 V dc to +7 V dc Logic input voltage range -0.3 V dc to VCC1Receiver differential voltage . 40 Vp-p Receiver common mode voltage range . -10 V dc to +10 V dc Driver peak output current: Device types 01, 02, 05, 06, 07, a
19、nd 08. 200 mA Device types 03 and 04 . 350 mA Power dissipation (PD) at TC= +125C: Device types 01, 02, 07, and 08 . 3.816 W Device type 03 and 04 . 1.591 W Device type 05 and 06 . 0.70 W Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ)
20、: Device types 01, 02, 05, 06, 07, and 08. +160C Device types 03 and 04 . +167C 2/ Thermal resistance, junction-to-case (JC): Device types 01, 02, 05, and 06 . 18C/W Device type 03 and 04 88C/W Device type 07 and 08 . 60C/W Thermal resistance, junction to ambient (JA): Device types 01, 02, 05, 06, 0
21、7, and 08 -35C/W Device type 03 and 04 . 118C/W _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Maximum junction temperature rise above case temperature for the hotte
22、st die at 100 percent transmitting duty cycle shall be 42C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 22
23、34 APR 97 1.4 Recommended operating conditions. Supply voltage: VCC(device types 01, 02, 05, and 06) +11.2 V dc to +12.6 V dc VCC(device types 03, 04, 07, and 08) +11.4 V dc to +12.6 V dc VEE(device types 01 and 02). -11.2 V dc to -12.6 V dc VEE(device types 03, 04, 07, and 08) -11.4 V dc to -12.6 V
24、 dc VCC1. +4.5 V dc to +5.5 V dc Logic input voltage range 0 V dc to +5.0 V dc Receiver differential voltage 30 Vp-p Receiver common mode voltage . -10.0 V dc to +10.0 V dc Driver peak output current: Device types 01, 02, 05, and 06. . 220 mA Device type 03 and 04 . 350 mA Serial data rate . 1.0 MHz
25、 maximum Junction temperature (TJ) Devices types 01, 02, 05, 06, 07 and 08 . +150C maximum Device types 03 and 04 +167C 1/ Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and
26、 handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE
27、 STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are
28、available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the referen
29、ces cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Maximum junction temperature rise above case temperature for the hottest die at 100 percent transmitting duty
30、 cycle shall be 42C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requ
31、irements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applic
32、able device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or funct
33、ion of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1.
34、 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Waveforms. The waveforms shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in tab
35、le I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) sha
36、ll be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein
37、shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall b
38、e maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compl
39、iance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered
40、to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described
41、 herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control an
42、d shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAor TCas specified in the approved m
43、anufacturers QM plan. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without
44、license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Unit Test Symbol Conditions -55C TC +125C unless otherwise specified Gr
45、oup A subgroups Device type Min Max Receiver Input level VLDifferential input, pin 15 to pin 16 4,5,6 All 40 Vp-p 01, 02, 05, 06, 07, 08 -10 +10 Input common mode voltage range VICMIndependent of xfmr or in accordance with MIL-HDBK-1553, section 5.1.2.2 4,5,6 03, 04 -5 +5 V(pk) IOL= 8 mA 01,02, 03 0
46、4, 05, 06 0.5 Output low voltage VOL IOL= 4 mA 1,2,3 07, 08 0.5 V Output high voltage VOHIOH= -0.4 mA 1,2,3 All 2.5 V Transmitter Input low voltage VIL1,2,3 All 0.7 V Input high voltage VIH1,2,3 All 2 V 01,02,05, 06,07,08 -1.6 Input low current IIL VIL= 0.4 V 1,2,3 03, 04 -0.4 mA Input high current
47、IIH VIH= 2.7 V 1,2,3 All 0.04 mA Output voltage VOAcross 35 load 1,2,3 All 6 9 V(pk) Output noise voltage VONAcross 35 load 4,5,6 All 10 mVp-p See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN
48、G SIZE A 5962-90829 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit Receiver strobe Input low voltage VSIL1,2,3 All 0.7 V Input high voltage VSIH1,2,3 All 2 V 01,0
