1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate. Add device class V criteria. - jak 02-12-19 Thomas M. Hess B Add case outline D. Add table III, delta limits. Editorial changes throughout. - jak 03-09-11 Thomas M. Hess C Update test conditions for VOHand VOLin table I. Updat
2、e boilerplate paragraphs to the current MIL-PRF-38535 requirements - jak 10-03-08 Thomas M. Hess REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHE
3、CKED BY Monica L. Poelking COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, HIGH SPEED CMOS, HEX INVERTER, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DR
4、AWING APPROVAL DATE 89-10-24 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89747 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E121-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY C
5、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead fin
6、ishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962-89747 01 C A Drawing number Device t
7、ype Case outline Lead finish (see 1.2.2) (see 1.2.4) (see 1.2.5) For device class V: 5962 - 89747 01 V C A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 R
8、HA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A das
9、h (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 54HCT04 Hex inverter, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the pr
10、oduct assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-c
11、ertification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter
12、 Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S
13、IZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/
14、 Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage . -0.5 V dc to VCC+0.5 V dc DC output voltage . -0.5 V dc to VCC+0.5 V dc Input diode current . 20 mA DC output diode current (per pin) 20 mA DC drain current (per pin) 25 mA DC VCCor GND current (per pin) . 50 mA Storage temperatur
15、e range (TSTG) . -65C to +150C Maximum power dissipation (PD) 500 mW 3/ Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc
16、Case operating temperature range (TC) . -55C to +125C Input rise or fall time (tr, tf) . 0 to 500 ns 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise sp
17、ecified, all voltages are referenced to ground. 3/ For TC= +100C to +125C, derate linearly at 12 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218
18、-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these docum
19、ents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Comp
20、onent Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 R
21、obbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unl
22、ess a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification i
23、n the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The d
24、esign, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The termi
25、nal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specifie
26、d on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shal
27、l be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 432
28、18-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer ha
29、s the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Ce
30、rtification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificat
31、e of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-10
32、3 and QML-38535 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M,
33、the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing
34、. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC
35、, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices
36、covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990
37、 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Test conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups Limits Unit Min Max High-level output voltage VOHVIH= 2.0 V or VIL= 0.8 V VCC= 4.5 V IO= -20 A 1, 2, 3 4.4 V VIH=
38、 2.0 V or VIL= 0.8 V VCC= 4.5 V IO= -4.0 mA 1, 2, 3 3.7 Low-level output voltage VOLVIH= 2.0 V or VIL= 0.8 V VCC= 4.5 V IO= +20 A 1, 2, 3 0.1 V VIH= 2.0 V or VIL= 0.8 V VCC= 4.5 V IO= +4.0 mA 1, 2, 3 0.4 High-level input voltage VIH2/ VCC= 4.5 V 1, 2, 3 2.0 V Low-level input voltage VIL2/ VCC= 4.5 V
39、 1, 2, 3 0.8 V Input capacitance CINVIN= 0.0 V, TC= +25C See 4.4.1d 4 10 pF Quiescent current ICCVIN= VCCor GND VCC= 5.5 V IOUT= 0.0 A 1, 2, 3 40 A Input leakage current IINVIN= VCCor GND VCC= 5.5 V 1, 2, 3 1.0 A Additional quiescent supply current ICCAny one input: VIN= 2.4 V or 0.5 V Other inputs:
40、 VIN= VCCor GND VCC= 5.5 V IOUT= 0.0 A 1, 2, 3 3.0 mA Functional tests See 4.4.1b 7, 8 Propagation delay, time, mA to mY tPLH, tPHL3/ VCC= 4.5 V CL= 50 pF See figure 4 9 20 ns 10, 11 30 Transition time high-to-low low-to-high tTHL, tTLH4/ VCC= 4.5 V CL= 50 pF See figure 4 9 15 ns 10, 11 22 1/ For a
41、power supply of 5.0 V 10%, the worst case output voltages (VOHand VOL) occur for HCT at 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. The worst case VIHand VILoccur at VCC= 5.5. V and 4.5 V, respectively. 2/ Test not required if applied as a forcing function for VOHor
42、 VOL. 3/ For propagation delay tests, all paths must be tested. 4/ Transition times (tTLH, tTHL) shall be guaranteed, if not tested, to the limits specified in table I.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE
43、 A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines C, D 2 Terminal number Terminal symbol 1 1A NC2 1Y 1A 3 2A 1Y 4 2Y 2A 5 3A NC 6 3Y 2Y 7 GND NC 8 4Y 3A 9 4A 3Y 10 5Y GND 11 5A NC 12 6Y 4Y 13 6A 4A 14 VC
44、C5Y 15 - - - NC 16 - - - 5A 17 - - - NC 18 - - - 6Y 19 - - - 6A 20 - - - VCCNC = No internal connection Pin descriptionsmA (m = 1 to 6) Data inputsmY (m = 1 to 6) Data outputs (inverted) FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
45、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Inputs Outputs mA mY H L L H H = High voltage level L = Low voltage level FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided
46、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes probe and test fixture capacitance. 2.
47、 Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO= 50, tr= 6.0 ns, tf= 6.0 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 4. Switching wavefo
48、rms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89747 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in a
