1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990http:/www.landandmaritime.dla.mil THIS
2、DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, HIGH POWER, OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 11-10-13 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-11228 SHEET 1 OF 13 DSCC FORM 223
3、3 APR 97 5962-E393-11Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documen
4、ts five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2
5、PIN. The PIN shall be as shown in the following example: 5962 R 11228 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance
6、(RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit
7、 function 01 MSK 106RH Radiation hardened, operational amplifier (1 ampere output) 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification a
8、s well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level.
9、 This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified
10、incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specifi
11、ed in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This pr
12、oduct may have a limited temperature range. 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 20 Flat pack with straight leads Y See figure 1 20 Flat pack with gull wing leads Provided
13、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-3
14、8534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) 22 V dc Differential input voltage 30 V dc Common mode input voltage . 15 V dc Output peak current . 2 A Thermal resistance, junction-to-case at 125C (JC) 6.0C/W Junction temperature (TJ) +150C Storage temperature range -65C to +150C Lead t
15、emperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Supply voltage (VCC) 15 V dc Case operating temperature range (TC) . -55C to +125C 1.5 Radiation features. Maximum total dose available 100 Krads (Si) 2/ 3/ 4/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standar
16、ds, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid M
17、icrocircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - S
18、tandard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the te
19、xt of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the max
20、imum levels may degrade performance and affect reliability. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, met
21、hod 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A. 3/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device types have not been characterized for displacement damage. 4/ See figure 3. Prov
22、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item perfor
23、mance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class.
24、 The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device
25、for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connec
26、tions. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as sp
27、ecified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of d
28、evices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device describ
29、ed herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This da
30、ta shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawin
31、g. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provid
32、ed with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not af
33、fect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufactu
34、rer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1
35、015 of MIL-STD-883. (2) TC= +125C minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networki
36、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC+125C unless otherwise specif
37、ied Group A subgroups Device type Limits Unit Min Max Quiescent current IIN VIN= 0 V 1 01 3.5 mA 2,3 7.5 Input offset voltage VIO VIN= 0 V 1 01 3.0 mV 2,3 5.0 Input bias current IIB VCM= 0 V, either input 1 01 500 nA 2,3 2.0 A Input offset current IIO VCM= 0 V 1 01 100 nA 2,3 300 Input resistance 4/
38、 RIN F = DC, TC= +25C 1 01 0.3 M Power supply rejection ratio PSRR VCC= 5 V to 15 V 1,2,3 01 80 dB Common mode rejection ratio 5/ CMRR F = 10 Hz, VCM= 10 V 4,5,6 01 70 dB Output voltage swing 5/ VO RL= 100, F = 100 Hz 4,5,6 01 13.5 V RL= 10, F = 100 Hz, TC= +25C 4 11 Output short circuit current ISC
39、 RSC= 0.5, VOUT= Max TC= +25C 4 01 0.8 1.6 A Slew rate SRVOUT= 10 V, RL= 10, TA= +25C 4 01 1.2 V/s M,D,P,L,R 1/ 4 1.1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA L
40、AND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Open loop voltage gain 5/ AVS RL= 1 k, f
41、= 10 Hz, TA= +25C 4 01 100 dB 5,6 88 Transitions times (Rise and Fall) tts 1 V to 2 V pk rise and fall, TA= +25C 9 01 1.0 s M,D,P,L,R 1/ 9 1.2 Small signal overshoot OS1 V to 2 pk, TA= +25C 4 01 20 % 1/ Device type 01 has been characterized through all levels M, D, P, L, and R of irradiation. Howeve
42、r, device type 01 is tested at 1.5 times the R level. Pre and post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TC= +25C. 2/ Unless otherwise specified: VS= 15 V, CC= 3000 pF. 3/ These parts may be
43、 dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ Parameter shall be guaranteed to the limits specified i
44、n table I for all lots not specifically tested. 5/ Parameter shall be guaranteed to the limits specified for subgroups 5 and 6 for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
45、5962-11228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters InchesMin Max Min Max A - 3.94 - .155 A1 1.80 2.31 .071 .091 b 0.25 0.51 .010 .020 c 0.13 0.38 .005 .015 D/E 16.62 16.13 .615 .635 e 1.27 TYP .050 TYP e1 11.18 1
46、1.68 .440 .460 L 12.70 - .500 - S1 2.21 REF .087 REF NOTES: 1. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units sh
47、all take precedence. 2. Pin numbers are for reference only. 3. Case outline X weight: 4.1 grams typical. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11228 DLA LAND AND MARITIME CO
48、LUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 Case outline Y . Symbol Millimeters InchesMin Max Min Max A - 3.94 - .155 A1 0.08 0.58 .003 .023 b 0.25 0.51 .010 .020 c 0.13 0.38 .005 .015 D/E 16.62 16.13 .615 .635 D1 20.70 21.21 .815 .835 D2 18.16 18.67 .715 .735 e 1.27 TYP .050 TYP e1 11.18 11.68 .440 .460 L1/L2 1.02 1.52 0.040 0.060 S1 2.21 REF .087 RE
