1、 MS51070E 15 January 2009 SUPERSEDING MS51070D 26 January 1981 DETAIL SPECIFICATION SHEET BELTS, V: ENGINE ACCESSORY DRIVE (1.000 INCH WIDTH) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described here
2、in shall consist of this specification sheet and MIL-DTL-11040. 1.000 inch accessory drive belts are not recommended for new design Effective length Effective length Effective length Effective length Dash no. Inches mm Dash no. Inches mm Dash no. Inches mm Dash no. Inches mm -28 28 711.2 -39 39 990.
3、6 -50 50 1270.0 -62 62 1574.8 -29 29 736.6 -40 40 1016.0 -51 51 1295.4 -64 64 1625.6 -30 30 762.0 -41 41 1041.4 -52 52 1320.8 -66 66 1676.4 -31 31 787.4 -42 42 1066.8 -53 53 1346.2 -68 68 1727.2 -32 32 812.8 -43 43 1092.2 -54 54 1371.6 -70 70 1778.0 -33 33 838.2 -44 44 1117.6 -55 55 1397.0 -72 72 18
4、28.8 -34 34 863.6 -45 45 1143.0 -56 56 1422.4 -74 74 1879.6 -35 35 889.0 -46 46 1168.4 -57 57 1447.8 -76 76 1930.4 -36 36 914.4 -47 47 1193.8 -58 58 1473.2 -78 78 1981.2 -37 37 939.8 -48 48 1219.2 -59 59 1498.6 -80 80 2032.0 -38 38 965.2 -49 49 1244.6 -60 60 1524.0 INCH-POUND FIGURE 1. V, belt: engi
5、ne accessory drive. AMSC N/A FSC 3030Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS51070E 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. The Part or Identifying Number (PIN) shall consist of the MS
6、sheet number plus the length dash number. When a plain based belt is required, the dash (-) shall be deleted and code letter “P” shall be added. When a notched or cogged based belt is required, the dash shall be deleted and the code letter “C” shall be added. When grade “B” belts are required, the l
7、etter “B” shall be added after the length dash number. When a matched set of belts is required, a second dash number shall be included after the base, length, and grade dash number. 4. Oil-resistance, as specified in MIL-DTL-11040 when oil-resistance is specified, the PIN shall include the letter “R
8、”. 5. Belt lengths as specified in terms of effective length as measured in accordance with the acquisition specification. These lengths cannot be compared to inside or outside circumference measurements. 6. Plain and notched (cogged) base belts are completely interchangeable on most drives when a p
9、lain or notched (cogged) base belt is specifically required. The user shall forward to the procuring activity information to substantiate the particular base configuration drive configuration, pulley sizes, rpm of driver pulley, horsepower requirements of each driven pulley, ambient temperature in w
10、hich belt must operate, item belt is used on, and other pertinent information. 7. MS51070 belts (MIL-DTL-11040) are a -65F use (-54C) belts if -65F is not a requirement of the end item, do not use this specification conform to A-A-52155 belts. 8. For design feature purposes, this specification takes
11、 precedence over procurement documents referenced herein. 9. Referenced documents shall be of the issue in effect on date of invitations for bids, or request for proposal, except that referenced adopted industry documents shall give the date of the issue adopted. Examples: Single belt, option of pla
12、in, notched or cogged, grade A MS51070 - 30 Effective length MS number Single belt, plain based, grade B MS51070 P 30 B Plain baseEffective length Grade BMS number FIGURE 1. V, belt: engine accessory drive Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
13、e from IHS-,-,-MS51070E 3 Single belt, notched or cogged base, grade B MS51070 C 30 B Notched or coggedEffective length Grade B MS number Matched set of belt, option of plain, notched or cogged base, grade A MS51070 -30 - 4 Number of Belts in Set Effective length MS numberMatched set of belt, notche
14、d or cogged base, grade B MS51070 C 30 B 4 Effective length Grade B MS numberNotched or CoggedNumber of Belts in Set Single belt, option of plain, notched or cogged, grade A MS51070 R 30 Oil-ResistanceEffective length MS number FIGURE 1. V, belt: engine accessory drive Continued. Provided by IHSNot
15、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS51070E 4 Single belt, plain base, grade B MS51070 R P 30 B Grade B Plain BaseEffective length Oil-ResistanceMS numberFIGURE 1. V, belt: engine accessory drive Continued. Dimensions: See figure 1. Changes from previous i
16、ssue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-11040, this document references the following: A-A-52155 CONCLUDING MATERIAL Custodians: Preparing activity: Ar
17、my - AT DLA - CC Navy - YD Air Force - 99 DLA - CC (Project 3030-2008-009) Review activities: Army - AR Navy - AS, MC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
