欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    DLA MS500077 REV E-2006 HOSE ASSEMBLY RUBBER HYDRAULIC AND PNEUMATIC MEDIUM PRESSURE FEMALE 37 DEGREES FLARED TUBE《橡胶软管装配 中压液压 37度气动阴扩口管》.pdf

    • 资源ID:697280       资源大小:41.19KB        全文页数:3页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    DLA MS500077 REV E-2006 HOSE ASSEMBLY RUBBER HYDRAULIC AND PNEUMATIC MEDIUM PRESSURE FEMALE 37 DEGREES FLARED TUBE《橡胶软管装配 中压液压 37度气动阴扩口管》.pdf

    1、INCH-POUNDMS500077E 17 May 2006 SUPERSEDING MS500077D 16 August 2002 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, RUBBER: HYDRAULIC AND PNEUMATIC, MEDIUM PRESSURE, FEMALE 37 FLARED TUBE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements

    2、 for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-13531. NOTES: 1. All undimensioned pictorial representations are for reference purposes only. 2. Metric equivalents are given for information only. 3. Dimension “L” is the defined length of the hose ass

    3、embly. 4. Hose assemblies shall be specified in the following length increments: Under 24 inches (0.61 m) inch (12.70 mm) increments. 24 to 36 inches (0.61 m to 0.91 m) - 1-inch (25.40 mm) increments. Over 36 inches (0.91 m)- in not less than 2-inch (50.80 mm) increments. 5. Tolerances: 1/8 inch (.1

    4、25 inch) (38.10 mm) for length under 24 inches (0.61 m). 1/4 inch (.250 inch) (76.20 mm) for the length from 24 to 36 inches (0.61 m to 0.91 m). 1% for length over 36 inches (0.91 m). FIGURE 1. General configuration. AMSC N/A FSC 4720 Provided by IHSNot for ResaleNo reproduction or networking permit

    5、ted without license from IHS-,-,-MS500077E 2TABLE I. Hose and fitting thread sizes. Hose OD reference Hose ID Reference Class A Class B Size Hose designator Inches mm Inches mm Inches mm Fitting thread reference 3 4 5 6 8 10 12 14 16 20 24 32 .187 .250 .312 .375 .500 .635 .750 .875 1.000 1.250 1.500

    6、 2.000 5.0 6.5 8.0 9.5 12.5 15.9 19.0 22.0 25.5 32.0 38.0 51.0 .500 .625 .688 .781 .906 1.031 1.187 1.313 1.500 1.812 2.082 2.625 12.5 15.9 17.5 20.0 23.0 26.0 30.0 33.3 38.1 46.0 53.0 66.7 .465 .527 .590 .684 .805 .930 1.086 1.211 1.430 1.741 1.968 2.500 11.8 13.4 15.0 17.4 20.5 23.6 27.6 31.0 36.3

    7、 44.2 50.0 63.5 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12 REQUIREMENTS Design and configuration: See figure 1 and table I. Hose material: Type I, class A or B. Hose and fittings shall be in accordance with MIL-DTL-13531. Fittings: Dimensions

    8、 in accordance with SAE-J516 female 37, flared type, swivel. Fitting material and finish shall be in accordance with MIL-DTL-13531 and designated as follows: A - Steel Cadmium plated. S - Stainless steel. Z - Steel -zinc plated (not for use in aircraft.). Provided by IHSNot for ResaleNo reproduction

    9、 or networking permitted without license from IHS-,-,-MS500077E 3Part or Identifying Number (PIN). The PIN is to be used for hose assemblies acquired to this specification. Example is shown below: MS500077 X XX XXX X A Prefix for all PINs Class (A or B) from table I. Dash number from table I. (one o

    10、r two digits) Length of hose assembly in inches. (Always use 3 digits. Use leading zeros as required). Fractional length in eighths of an inch. (0 through 7) Hose fitting material and plating Changes from previous issue: The margins of this specification are marked with asterisks to indicate where c

    11、hanges from the previous issue were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of th

    12、e marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-13531, this document references the following: SAE-J516 CONCLUDING MATERIAL Custodians: Preparing activity:Army - AT DLA - CC Navy - SH Air Force - 99 (Project 4720-2005-009) DLA - CC Revie

    13、w activities: Army - AR, AV, CR4, MI Navy - AS, MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(DLA MS500077 REV E-2006 HOSE ASSEMBLY RUBBER HYDRAULIC AND PNEUMATIC MEDIUM PRESSURE FEMALE 37 DEGREES FLARED TUBE《橡胶软管装配 中压液压 37度气动阴扩口管》.pdf)为本站会员(figureissue185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开