1、AMSC N/A FSC 4730 MS39212J 30 August 2012 SUPERSEDING MS39212H 24 March 2008 DETAIL SPECIFICATION SHEET SLEEVES, COMPRESSION, TUBE - HOSE FITTING- SAFETY SLEEVE TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring th
2、e product described herein shall consist of this specification sheet. Inches mm .007 .015 0.18 0.38 FIGURE 1. Sleeves, compression, tube - hose fitting - safety sleeve type. Inactive for new design after 29 December 1967. For new design, use SAE-J514. INCH-POUND Provided by IHSNot for ResaleNo repro
3、duction or networking permitted without license from IHS-,-,-MS39212J 2 Dash number Tube OD Inches (mm) A dia. Inches (mm) B dia. Inches (mm) C Inches (mm) D Inches (mm) 1 .125 (3.18) .129 (3.28) .131 (3.33) .160 (4.06) .150 (3.81) .213 (5.41) .203 (5.16) .281 (7.14) .275 (6.99) 2 .188 (4.78) .190 (
4、4.83) .193 (4.90) .250 (6.35) .230 (5.84) .322 (8.18) .312 (7.92) .281 (7.14) .275 (6.99) 3 .250 (6.35) .255 (6.48) .258 (6.55) .316 (8.03) .296 (7.52) .380 (9.65) .370 (9.40) .339 (8.61) .333 (8.46) 4 .313 (7.95) .318 (8.08) .321 (8.15) .379 (9.63) .359 (9.12) .448 (11.38) .438 (11.13) .339 (8.61)
5、.333 (8.46) 5 .375 (9.53) .380 (9.65) .383 (9.73) .441 (11.20) .421 (10.69) .505 (12.83) .495 (12.57) .378 (9.60) .372 (9.45) 6 .500 (12.70) .506 (12.85) .509 (12.93) .567 (14.40) .547 (13.89) .635 (16.13) .625 (15.88) .378 (9.60) .372 (9.45) 7 .625 (15.88) .633 (16.08) .636 (16.15) .694 (17.63) .67
6、4 (17.12) .760 (19.30) .750 (19.05) .418 (10.62) .412 (10.46) 8 .750 (19.05) .758 (19.25) .761 (19.33) .819 (20.80) .799 (20.29) .885 (22.48) .875 (22.23) .418 (10.62) .412 (10.46) 9 .875 (22.23) .883 (22.43) .886 (22.50) .944 (23.98) .924 (23.47) 1.010 (25.65) 1.000 (25.40) .418 (10.62) .412 (10.46
7、) 10 1.000 (25.40) 1.008 (25.60) 1.011 (25.68) 1.069 (27.15) 1.049 (26.64) 1.135 (28.83) 1.125 (28.58) .418 (10.62) .412 (10.46) 11 1.250 (31.75) 1.261 (32.03) 1.264 (32.11) 1.322 (33.58) 1.302 (33.07) 1.416 (35.97) 1.406 (35.71) .418 (10.62) .412 (10.46) 12 1.500 (38.10) 1.511 (38.38) 1.514 (38.46)
8、 1.572 (39.93) 1.552 (39.42) 1.666 (42.32) 1.656 (42.06) .418 (10.62) .412 (10.46) FIGURE 1. Sleeves, compression, tube - hose fitting - safety sleeve type - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39212J 3 Dash number E Inches (
9、mm) F dia. Inches (mm) G dia. Inches (mm) H Inches (mm) J radius Inches (mm) 1 .084 (2.13) .078 (1.98) .178 (4.52) .175 (4.45) .140 (3.56) .015 (0.38) .023 (0.58) .010 (.25) 2 .084 (2.13) .078 (1.98) .256 (6.50) .252 (6.40) .205 (5.21) .020 (0.51) .028 (0.71) .020 (0.51) 3 .102 (2.59) .096 (2.44) .3
10、38 (8.59) .334 (8.48) .268 (6.81) .024 (0.61) .038 (0.97) .020 (0.51) 4 .102 (2.59) .096 (2.44) .400 (10.16) .396 (10.06) .330 (8.38) .024 (0.61) .038 (0.97) .020 (0.51) 5 .122 (3.10) .116 (2.95) .461 (11.71) .457 (11.61) .393 (9.98) .024 (0.61) .038 (0.97) .020 (0.51) 6 .122 (3.10) .116 (2.95) .589
11、 (14.96) .585 (14.86) .521 (13.23) .024 (0.61) .038 (0.97) .020 (0.51) 7 .122 (3.10) .116 (2.95) .715 (18.16) .711 (18.06) .647 (16.43) .024 (0.61) .038 (0.97) .020 (0.51) 8 .122 (3.10) .116 (2.95) .840 (21.34) .836 (21.23) .772 (19.61) .024 (0.61) .038 (0.97) .020 (0.51) 9 .122 (3.10) .116 (2.95) .
12、965 (24.51) .961 (24.41) .897 (22.78) .024 (0.61) .038 (0.97) .020 (0.51) 10 .122 (3.10) .116 (2.95) 1.090 (27.69) 1.086 (27.58) 1.022 (25.96) .024 (0.61) .038 (0.97) .020 (0.51) 11 .122 (3.10) .116 (2.95) 1.344 (34.14) 1.340 (34.04) 1.275 (32.39) .024 (0.61) .038 (0.97) .020 (0.51) 12 .122 (3.10) .
13、116 (2.95) 1.593 (40.46) 1.589 (40.36) 1.524 (38.71) .024 (0.61) .038 (0.97) .020 (0.51) NOTES: 1. Dimensions are in inches, unless otherwise specified. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance for 3 place decimals is .005 inch (0.13 mm), toleran
14、ce for fractions is 1/64, tolerance for degrees is 2. 4. This illustration is for identification and is not intended to restrict designs or shapes not dimensioned. FIGURE 1. Sleeves, compression, tube - hose fitting - safety sleeve type - Continued. REQUIREMENTS: Dimensions and configuration: See fi
15、gure 1. Material: Carbon steel AISI-C1112, AISI-C1113, AISI-C1117, AISI-C1118 or AISI-C1137 in accordance with SAE AIR4127. Finish: All platings shown in table I shall be capable of meeting the 96 hour salt spray test in accordance with ASTM B117. Provided by IHSNot for ResaleNo reproduction or netw
16、orking permitted without license from IHS-,-,-MS39212J 4 TABLE I. Material and finish designators. Designator Material Finish Blank Steel Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. G Steel Zinc plating with chromate conversion in accor
17、dance with ASTM B695, type II, class 5. H Steel Zinc phosphate in accordance with MIL-DTL-16232, type Z, class 1 and shall be hexavalent chromium free. J Steel Zinc plating with chromate conversion in accordance with ASTM B633; type VI, Fe/Zn 25 N Steel NAVAIR trivalent chromium pretreatment (TCP) i
18、n accordance with MIL-DTL-81706, type II, class 1a. P Steel Zinc plating with colorless passivate in accordance with ASTM B633, type VI, Fe/Zn 5. S Corrosion resistant steel 1/ No additional finish. Passivation in accordance with SAE-AMS2700, type 6 or 7. 1/ V Steel Zinc nickel in accordance with SA
19、E-AMS2417, type 1. 1/ Stainless steel of such hardness as to be capable of biting, fully annealed type 304 stainless steel tubing. Part or Identifying Number (PIN) example: MS39212 - 1 R MS number Dash number (see figure 1) Material and finish designator, see table I. Guidance on use of alternative
20、parts with less hazardous or non-hazardous materials. This specification provides an alternate material, corrosion resistant steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their For old designs
21、that use compression sleeves, shall be done in accordance with MS39212. Table II shows supersession data to compression sleeves in accordance with SAE-J514. These replacements are for new design. Users are cautioned to evaluate replacements for their particular application. Provided by IHSNot for Re
22、saleNo reproduction or networking permitted without license from IHS-,-,-MS39212J 5 TABLE II. Supersession data. Inactive PIN Active SAE Inactive PIN Active SAE Compression PIN 1/ Compression PIN 2/ MS39212-1A J514-2-080115ACQ MS39212-1AP J514-2-080115ACP MS39212-2A J514-3-080115ACQ MS39212-2AP J514
23、-3-080115ACP MS39212-3A J514-4-080115ACQ MS39212-3AP J514-4-080115ACP MS39212-4A J514-5-080115ACQ MS39212-4AP J514-5-080115ACP MS39212-5A J514-6-080115ACQ MS39212-5AP J514-6-080115ACP MS39212-6A J514-8-080115ACQ MS39212-6AP J514-8-080115ACP MS39212-7A J514-10-080115ACQ MS39212-7AP J514-10-080115ACP
24、MS39212-8A J514-12-080115ACQ MS39212-8AP J514-12-080115ACP MS39212-9A J514-14-080115ACQ MS39212-9AP J514-14-080115ACP MS39212-10A J514-16-080115ACQ MS39212-10AP J514-16-080115ACP MS39212-11A J514-20-080115ACQ MS39212-11AP J514-20-080115ACP MS39212-12A J514-24-080115ACQ MS39212-12AP J514-24-080115ACP
25、 Inactive PIN Active SAE Inactive PIN Active SAE Compression PIN 3/ Compression PIN 4/ MS39212-1AJ or R J514-2-080115ACZ MS39212-1ASS J514-2-080115AS MS39212-2AJ or R J514-3-080115ACZ MS39212-2ASS J514-3-080115AS MS39212-3AJ or R J514-4-080115ACZ MS39212-3ASS J514-4-080115AS MS39212-4AJ or R J514-5-
26、080115ACZ MS39212-4ASS J514-5-080115AS MS39212-5AJ or R J514-6-080115ACZ MS39212-5ASS J514-6-080115AS MS39212-6AJ or R J514-8-080115ACZ MS39212-6ASS J514-8-080115AS MS39212-7AJ or R J514-10-080115ACZ MS39212-7ASS J514-10-080115AS MS39212-8AJ or R J514-12-080115ACZ MS39212-8ASS J514-12-080115AS MS392
27、12-9AJ or R J514-14-080115ACZ MS39212-9ASS J514-14-080115AS MS39212-10AJ or R J514-16-080115ACZ MS39212-10ASS J514-16-080115AS MS39212-11AJ or R J514-20-080115ACZ MS39212-11ASS J514-20-080115AS MS39212-12AJ or R J514-24-080115ACZ MS39212-12ASS J514-24-080115AS 1/ Designator “C” is for steel, “Q” is
28、for cadmium plating. 2/ Designator “C” is for steel, “P” is for zinc phosphate plating. 3/ Designator “C” is for steel, “Z” is for zinc plating. 4/ Designator “S” is for corrosion resistant steel. Changes from previous issue. The margins of this specification are marked with vertical lines to indica
29、te where changes from the previous issue were made. This was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespec
30、tive of the marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: MIL-DTL-16232 MIL-DTL-81706 ASTM B117 ASTM B633 ASTM B695 SAE-AMS-C-81562 SAE-AMS2417 SAE-AMS2700 SAE AIR4127 SAE-AMS-QQ-P-416 SAE-J514 Provided by IHSNot for Res
31、aleNo reproduction or networking permitted without license from IHS-,-,-MS39212J 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy SH Air Force - 99 DLA - CC (Project 4730-2012-042) Review activities: Army - AR Navy - AS, MC, SA Air Force- 71 NOTE: The activities listed a
32、bove were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
